{Change Comments ***********************************************************}

{8/11/89, Updated processor JR}
{8/31/89, Added PostScript, JR}
{12/1/89, Updated: Fanuc 11M M007.61, JR}
{2/7/90, Updated to Version 3.2 per Fanuc 6M M001.70 Format, DWB}
{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{9/28/90, Updated: Fanuc 11M M007.71 to .76.1 format, JR}

{12/13/90
Copied & modified: Fanuc 11M M007.76.1
For: DARMARK INC
Machine:
Control: Fanuc 11M
Changes following made per customer request:
Deleted all occurances of SpinOff (M5) command.
Added 'M19' to all occurances of IncValue OfstOff commands.
SK}

{2/22/91
Copied & modified: Fanuc 11M M007.76.2
For: Gibbs & Associates
Machine:
Control: Fanuc 11M
Updated to Version 3.4 per Fanuc 6M M001.76.3 Format.
DWB}

{4/02/91
Modified: Fanuc 11M M007.76.3
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
Kim Michelman}

{9/30/91
Modified: Fanuc 11M M007.79
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.81 Format.
Kim Michelman}

{7/21/95, Updated Fanuc 11M M007.81 to .85 format per Fanuc 6M M001.85.01, JR}

{1/17/96, Updated .85 to .86 version, MPK}

{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{2/25/98,
Initial: Fanuc 11M M007.89
Created: Fanuc 11M Mazak [SPP] MV19.89
For: SP Precision
Deleted 'G70' in safety start block and replaced with AbsOrInc.
Deleted all ToolChng.
Deleted all OfstOn.
Added literal 'G61.1K50' to line after CoolOn in FirstOp and NewTool.
Added literal 'G28X0.Y0.Z0.M19' at end of prog.
Added boolean to OpenMP so that if # of Fixture Offsets exceeds 6, then will
output literal 'G54.1P' and then PartNum# -6.
Added ZCP1 to line before CoolOn in FirstOp and NewTool.
CDH}

{03/02/98,
Initial: Fanuc 11M Mazak [SPP] MV19.89
Created: Fanuc 11M Mazak [SPP] MV19.89.1
For: SP Precision
Deleted all literal 'M19'.
Moved 'G28X0Y0Z0' in the end of prog section to after AllToolsOnePart? at end
of prog.
CDH}

{21Apr98
Original: Fanuc 11M Mazak [SPP] MV19.89.1
Created: Fanuc 11M Mazak [SPP] MV19.15
For: SP Precision
Changes made per: Frank Richard
Deleted old version numbers and comments e.g. {.62}, {commands}, {literals}, etc
Updated to.15 format per Fanuc 6M M001.15
Charles Winston}

{22Apr98
Original: Fanuc 11M Mazak [SPP] MV19.15
Created: Fanuc 11M Mazak [SPP] BV19.15
For: SP Precision
Changes made per: Frank Richard
Updated to B_Style Advanced Mill Post per Fanuc 6M (FW) B001.15
NOTE [1]:
Customer is using this post with Advanced Mill to Machine the FRONT and BACKs of parts
No Angular Moves appear in the output code and an Program Stop has been inserted if a rotation takes place.
The post then outputs a Comment instructing the Operator to manually rotate the part by the required amount.
NOTE [2]:
WFOCS is set to TRUE in ProgStart and, therefor, the post can never output G52 style offsets.
The control however switches to a G54.1P# style of output when CSPartNum# exceeds 6.
Changed FORMAT#3 from '*#####.###;0.' to '*####0.0##;0.'
Added Formatting for SUB# in Prog Numeric Format Definitions
Added a Boolean in CSWFO and DoCSG52Ops to switch to a G54.1P# style of output when CSPartNum# exceeds 6.
Added Logic to DoCSWFOComment for a Program Stop and Comment for the Operator
Deleted the MultipleParts Boolean in ProgStart and Added SetWFOCS to force WFOCS = TRUE
Note: the Literal 'G61.1K50' which appears in FirstOp3 and NewToolOp5 is a Command for the MAZAK which assists
'Look-Ahead' in the control although, because if where it is used, it looks just like a tool offset command. It is not.
Charles Winston}

{Prog Numeric Format Definitions ****}

#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*####0.0##;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(TrackZNO#,4)
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(CSSubID#,5)
FORMAT(Operation#,5)
FORMAT(SUB#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)

{Prog Subroutines ****}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

CSPartNum#:
ADD# CS# MUL# NumOfCS# SUB# PartNum# Num#('1')
RETURN

CSWFO:
IF LTEqual? CSPartNum# Num#('6')
'G' ADD# CSPartNum# Num#('53')
ELSE
'G54.1P' Sub# CSPartNum# Num#('6')
END
RETURN

WFO:
'G' ADD# PartNum# Num#('53')
RETURN

WFOStuff:
IF Flag?('2')
IF NOT SameTool?
IF WFOCS?
CSWFO
ELSE
WFO
END
ELSE
IF WFOCS?
IF ChangeCS?
IF MultipleParts?
{MP ChangeCS is handled in SubCSMP and CloseMP}
ELSE
CSWFO
END
END
END
END
END
SetFlagF('2')
RETURN

CSG52:
IF FirstOperation? OR NewTool? OR ChangeCS?
SeqC 'G52X' CSOffsetX# 'Y' CSOffsetY# 'Z' CSOffsetZ# EOL
END
ClearCSOffset
RETURN

G52Stuff:
IF AAxisAvail? OR BAxisAvail?
IF NOT WFOCS?
IF MultipleParts?
IF WorkFixtureOffsets?
CSG52
END
ELSE
CSG52
END
END
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoCSComment:
IF AAxisAvail? OR BAxisAvail?
'( CS#' CS# ' - ' CSComment$ ' )' EOL
END
RETURN

DoCSWFOComment:
IF AAxisAvail? OR BAxisAvail?
IF FirstOperation? OR NewTool? OR ChangeCS?
'( ' CSWFO ' = X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ#
IF AAxisAvail?
' A' CSOffsetA#
END
IF BAxisAvail?
' B' CSOffsetB#
END
' )' EOL
IF AChange? OR BChange?
SeqC 'M0' EOL
'( Rotate the Part '
IF AChange?
CSOffsetA# ' '
END
IF BChange?
CSOffsetB# ' '
END
'Deg. )' EOL
END
END
ClearCSOffset
END
RETURN

CSComments:
IF WFOCS?
IF MultipleParts?
IF OneToolAllParts? AND ExitClearancePlane?
ClearCSOffset { Necessary for correct StrtPos in Main }
END
ELSE
DoCSComment
DoCSWFOComment
END
ELSE
DoCSComment
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
CSComments
RETURN

CSAngleA:
IF AAxisAvail?
IF WFOCS?
'A0.'
ELSE
'A' CSOffsetA#
END
END
RETURN

CSAngleAC:
IF AChange?
CSAngleA
END
RETURN

CSAngleB:
IF BAxisAvail?
IF WFOCS?
'B0.'
ELSE
'B' CSOffsetB#
END
END
RETURN

CSAngleBC:
IF BChange?
CSAngleB
END
RETURN

PSInit:
NewWFOF
FourthCWF
FourthCCWF
FifthCWF
FifthCCWF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
SubID EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

ToggleIncDecWFO:
IF Flag?('3')
SetFlagF('3')
ELSE
SetFlag('3')
END
RETURN

DoCSG52Ops:
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
ELSE
IF GreaterThan? PartNum# Num#('6')
SeqC 'G54.1P' Sub# PartNum# Num#('6') EOL
ELSE
SeqC SetWFO EOL
END
END
SeqC SubCall CallLab RepLab OnePart EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
IF WFOCS?
StartSub
SaveCSProg
SaveCSOpStart
ClearCSOffset
ELSE
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-OTAP-ECP }
END
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoCSG52Ops
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoCSG52Ops
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
StartSub
END
ELSE
SeqC SubCall CallLab RepLab Parts EOL
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('2') { WFOStuff }
END
StartSub
END
RETURN

DoCSWFOOps:
EachCSOp
DoCSComment
DoCSWFOComment
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
ELSE
SeqC CSWFO EOL
END
SeqC SubCall CallLabB CSSubID# RepLab OnePart EOL
NextCSOp
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
IF WFOCS?
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-OTAP-ECP }
END
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoCSWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoCSWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
END
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

SubCSMP:
IF WFOCS?
IF ChangeCS?
SeqC EndSub EOL
CloseSub
NewProg
StartSub
SaveCSProg
END
ClearCSOffset
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqC AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN

ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN

ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC DoDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC DoAbsOrInc ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC DoAbsOrInc ckCRC FeedC MoveXYZC FeedRateC ckCRCNum EOL
DecelMove2
END
SeqC DoAbsOrInc ckCRC FeedC MoveXYZC DecelFeed ckCRCNum EOL
ELSE
SeqC DoAbsOrInc ckCRC FeedC MoveXYZC FeedRateC ckCRCNum EOL
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
Seq IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SeqC AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
Feed
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC IncValue StrtPosC EOL
AbsOrInc
END
END
SeqC ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
Rapid
IF SPXMove? OR SPYMove?
SeqC IncValue StrtPosC EOL
AbsOrInc
END
IF FeedEntry?
SeqC ZCP2PlusInc EOL
END
END
IF FeedEntry?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FirstCycle?
Rapid
END
SeqC RapidC ZInPlusInc EOL
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC SubCall CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL
END
END
SeqC SubCall CallLab EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqC EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

OpGuts:
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
IF FIFO?
SeqC FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
IF CallMasterOp?
SeqC SubCall 'P' CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqC SubCall CallLab EOL
StartSub
ToolPath
SeqC EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqC Rapid 'G80' ZCP3 EOL
IF Repeats?
FinishSubG92
END
END
END
RETURN

ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('12700')
ELSE
SetMaxFeed('500')
END
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetFlagF('2') { WFOStuff }
SetFlag('3') { True = incrementing WFO numbers for MP. False = decrementing WFO numebrs for MP }
SetFlag('4') { True = toggle between incrementing/decrementing WFO's }
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
SetWFOCS { Force WFOCS = TRUE, G52 Style of Output not Supported}
RETURN

InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
RETURN

FirstOp1:
Seq Plane AbsOrInc 'G80' CRCOff EOL
SeqC OpToolID EOL
DoOpComments
DoPostScript
RETURN

FirstOp2:
SeqC WFOStuff EOL
G52Stuff
SeqC Speed SpinOn EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
RETURN

FirstOp3:
SeqC ZCP1 EOL
SeqC CoolOn EOL
SeqC 'G61.1K50' EOL
RETURN

NewToolOp1:
SeqC CoolOff EOL
RETURN

NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SeqC AbsOrInc Rapid Home EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN

NewToolOp3: {Start new Operation}
Seq Plane 'G80' CRCOffC EOL
SeqC OpToolID EOL
DoOpComments
DoPostScript
RETURN

NewToolOp4:
SeqC WFOStuff EOL
G52Stuff
SeqC Speed SpinOn EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
RETURN

NewToolOp5:
SeqC ZCP1 EOL
SeqC CoolOn EOL
SeqC 'G61.1K50' EOL
RETURN

SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC IncValue OfstOff 'M19' EOL
SeqC SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset? OR ChangeCS?
SeqC IncValue OfstOff 'M19' EOL
END
END
RETURN

SameToolOp2: {Start new Operation}
DoOpComments
DoPostScript
CheckPass
RETURN

SameToolOp3: {Start new Operation}
SeqC WFOStuff EOL
G52Stuff
IF LAST ProgStop?
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC CoolOn EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN

End1:
SeqC CoolOff EOL
RETURN

End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqC AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
END
SeqC IncValue 'G28X0.Y0.Z0.' EOL
RETURN

End3:
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
OpenMP
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
SubCSMP
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
CloseMP
End3
RETURN

MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
FirstOp1
OpenMP
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
CloseMP
NewToolOp2 {to tool change, CS problem}
NewToolOp3
OpenMP
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
CloseMP
End2
End3
RETURN

MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
SetFlag('2')
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
OpenMP
FirstOp2 {need StrtPos in Sub}
ELSE
IF NewTool?
CloseMP
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
NewToolOp5
OpenMP
NewToolOp4 {need StrtPos in Sub}
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
CloseMP {End of program}
End1
End2
End3
RETURN

NoMPs: {no multiple parts}
EachOp {Start of post processing}
SetFlag('2') { WFOStuff }
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN

{Start of executable Prog, Top Level ****}

ProgStart {setup and initializations}

IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END