{Change Comments ***********************************************************}

{9/6/87
Created: Hurco M069.40
For: Ivac
For Hurco that has special executive with conventional NC}

{7/26/89
Copied & Modified: Hurco M069.53
For: Bio-Rad
Delete CRCOffsetC from ToolPath.
Added Sequence Numbers to all Comments.
New format for XYZ output in FormatArc sub.
JR}

{8/4/89
Modified: Hurco M069.54
For: Bio-Rad
Added code for Drilling and RetractToCP1.
Added StrtPos to Milling with Repeats.
JR}

{8/28/89
Modified: Hurco M069.55
For: Bio-Rad
Added Plane at FormatArc sub.
Deleted ReverseXZArcs command at setup and initializations.
JR}

{11/17/89
Modified: Hurco M069.56
For: Bio-Rad
Deleted Sequence Numbers from all Comments.
JR}

{3/30/90, Updated: Hurco M069.57 to .70.3 foramt, JR}

{5/29/90
Modified: Hurco M069.57
For: Bio-Rad
Set Arcs Stop on Quadrants to TRUE in Mach Spec.
Hurco CRC rules require this.
DWB}

{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}

{8/7/90
Copied & Modified: Hurco M069.71
For: Pyramid Precision
Machine: Hurco KMB 40
Control: Hurco Ultimax
Changed to use incremental unsigned drill depths.
Updated to .74 format.
JR}

{6/20/91
Modified: Hurco Ultimax BMC40 M330.73
For: Pyramid Precision Machine
Changed from conditional IJ & R arcs to forced
Updated to 4.0 per Fanuc M001
KLM}

{4/15/92
Changed & Modified: Hurco Ultimax BMC40 M330.80
For: Pyramid Precision Machine
Changes made per Customer Request
Added SpinOn to all Speed/SpeedC blocks.
Moved CoolOn from ZCP1 block to ZCP2 block at Milling and Drilling.
Commented out special CoolOn block after LAST CoolOff situation at SameTool.
This was necessary to suppress duplicate CoolOn output.
KLM}

{
Format: Hurco Ultimax [PPM] M496.80.2
5/12/95
Checked for move in ArcFeat? to prevent extra arcs from being output
TH}

{5/23/95
Updated: Hurco Ultimax [PPM] M496.80.2
For: Gibbs & Associates
Versions: ncCad 4.33.01/ncCAM 4.33.01/ncPost 4.33.05/Catalyst v2.14.40/Compost 4.21.28
Changes made per Tom Hubina/Pete Jackson
Added changes from Hurco MO69.81.8
6/6/91 Fixed 'cancel drill cycle' problem and forced I and J arcs.
6/5/92 Added the CRCOnC line to the ToolPath for Autocycles.
The Hurco rules state that the control must be set in G41/G42 prior to G91 for CRC to work
correctly.
Updated to Version 4.2 per LongHand M001.81.3h Format.
This Post Processor does not support subprograms.
Currently supports all combinations of MultipleParts, AutoCycles and Repeats.
Using Var(1), Var(2) and Var(3) for logical control of MultiplePart Operations.
Using Var(4), Var(5), Var(6) and Var(7) for correct Positioning of AutoCycles that Repeat in
X and/or Y, and when AbsoluteMoves = FALSE.
Corrected FORMAT #5 from '########;0' to '#######0'.
Corrected FORMAT #6 for Dwell# from '####^###;' to '####^##0'.
Added FORMAT #7, '#', for RapidF#.
Added Tag# to FORMAT #5.
Added Recall# to FORMAT #5.
Added RestoreScale Sub per 4-Axis Post Processor.
Added support of FIFO? Milling Operations.
Added TrackZNO# FIRST SPZ# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
Added logic of MPLoop sub to handle IF NewTool? and LastOp? situations.
Commented out DoEndOpPS at MPLoop for OneToolAllParts, it does not work correctly.
Added CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Added Move to ZInC for Non-AutoCycle FeedConnect Repeats with ZMoves at ExitMove sub.
Moved DoCycleComment call to before StrtPos move in related subs.
Added BadMPWFOReport sub.
Reports when MultipleParts AND WorkFixtureOffsets = TRUE AND EquallySpacedOffset values exist.
Added FORMAT #8, 'Ä…#bbbb.bbbb#', for PartShiftX#, PartShiftY# and PartShiftZ# commands.
Moved SeqC and EOL outside of IF ELSE condition at ExitMove sub.
Moved SeqC AbsOrInc and EOL outside of IF ELSE condition at AutoCycCutSub2 sub.
Deleted ReSetPass2 at end of ZonlyRepAutoCycle sub.
Already executed at end of call to AutoCycCutSub2 sub.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to RapidFeat at ToolPath.
Outputs G40 at all Z Retract blocks.
Modified support of CRC during multiple pocket dog-bone operation.
Modified condition to output CRCOffC for ZMoveOnly Feature at ToolPath RapidFeat.
Changed First occurance of GetConnect to RapidC at ZonlyRepAutoCycle sub.
FeedConnect only applies to Each Repeat, not Each Feature.
Modified CkCRC sub.
Changed logic to output CRCOnC in OneFeat, Non-ZMove ToolPath.
Added logic to suppress output of CRCOnC on ZMove Feature.
Deleted GetConnect sub, modified XYZRep, XYZRepAutoCycle and ZonlyRepAutoCycle subs, see 11/16/94.
DWB}

{2/9/96, Updated .81 number to .84, no changes necessary, MPK}

{3/22/96, Tested ZOnlyRepAutCycle, Incremented number to .87, MPK}

{9/17/96,
Initial: Hurco Ultimax [PPM] M496.87
Created: Hurco Ultimax Mxxx.87
For: Excellerated Mold
Modified order of saftey start commands,
deleted SpinOff at program end,
put M25 on line after move to home at progaram end
MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
#8 = 'Ä…#bbbb.bbbb#'
#9 = '+####.####;0.'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Tag#,5)
FORMAT(Recall#,5)
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(RapidF#,7)
FORMAT(PartShiftX#,8)
FORMAT(PartShiftY#,8)
FORMAT(PartShiftZ#,8)
FORMAT(SPZ#,9)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' Tag# ' )' EOL
END
RETURN

DoCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

BadMPWFOReport:
SetStatusOff
' ' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
'Ä„ NOTE: Even though you have elected to Ä„' EOL
'Ä„ process this file using Multiple Ä„' EOL
'Ä„ Parts with Work Fixtures, there exist Ä„' EOL
'Ä„ non-zero values in the invisible, Ä„' EOL
'Ä„ Equally SpacedÉ fields, as follows: Ä„' EOL
'Ä„ Ä„' EOL
'*****************************************' EOL
IF NotEqual? PartShiftX# Num#('0')
' X axis shift = ' PartShiftX# EOL
END
IF NotEqual? PartShiftY# Num#('0')
' Y axis shift = ' PartShiftY# EOL
END
IF NotEqual? PartShiftZ# Num#('0')
' Z axis shift = ' PartShiftZ# EOL
END
'*****************************************' EOL
'Ä„ Ä„' EOL
'Ä„ Please reset these values to zero as Ä„' EOL
'Ä„ they affect the coordinate values Ä„' EOL
'Ä„ output, starting with Part# 2. Ä„' EOL
'Ä„ Thank You. Ä„' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
' ' EOL
SetStatusOn
RETURN

PSInit: {reset flags}
RotateF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC FeedC ZInC FeedEntC EOL
ELSE
SeqC RapidC ZInC EOL
END
RETURN

ExitMove:
SeqC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN

ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN

CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
Plane
IF XYPlane?
MoveX MoveY MoveZC
ELSE
IF XZPlane?
MoveX MoveYC MoveZ
ELSE {YZPlane}
MoveXC MoveY MoveZ
END
END
IF ArcIJFormat?
ArcIJ
ELSE
ArcR
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
IF NOT ZMove?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CkCRC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqC CkCRC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CkCRC FeedC MoveXYZC FeedRateC EOL
END
END
RETURN

DoMoveSZ:
IF SPZMove? {.80.01}
SetAbs
TrackZNO# ClearancePlane2#
SetInc
'Z' SPZ#
SetAbsOrInc
END
RETURN

ToolPath:
EACHFeat
IF PointFeat? { Drilling Only }
IF RetractToCP1?
IF NOT FirstFeat?
SeqC DrillOff EOL
SeqC Rapid ZCP1 EOL
SeqC MoveSX MoveSY EOL
SeqC ZCP2 EOL
SeqC Cycle MoveSX MoveSY DoMoveSZ Peck FeedEnt EOL
END
ELSE { NOT RetractToCP1 }
SeqC MoveSXYC DoMoveSZ EOL {.80.01}
END
ELSE
IF RapidFeat?
IF AutoCycle?
IF LastFeat?
CRCOffC {.70}
END
SeqC RapidC MoveXYZC EOL
ELSE
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC {.82}
END
IF XMove? OR YMove? OR ZMove?
SeqC RapidC MoveXYZC EOL {.82}
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC FormatArc ArcFeedC EOL
END
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN

WFOStuff:
{ Note: This Post Processor does not support WorkFixtureOffsets. }
RETURN

AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
SeqC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN

Milling:
EntryMove
ToolPath
RETURN

XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
CRCOffC
IF FeedConnect?
SeqC FeedC StrtPosC FeedEntC EOL
IF ZShiftOnly?
EntryMove
END
ELSE
SeqC RapidC StrtPosC EOL
IF FeedEntry?
SeqC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN

NoRepAutoCycle:
EACHFeat
DoCycleComment
IF CutterRadiusCompensation?
SeqC CRCOnC RapidC MoveSX MoveSY EOL
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN

XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
IF CutterRadiusCompensation?
IF FeedConnect?
SeqC CRCOnC FeedC MoveSX MoveSY FeedEntC EOL
ELSE
SeqC CRCOnC RapidC MoveSX MoveSY EOL
END
ELSE
IF FeedConnect?
SeqC FeedC MoveSXYC FeedEntC EOL
ELSE
SeqC RapidC MoveSXYC EOL
END
END
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN

ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF CutterRadiusCompensation?
SeqC CRCOnC RapidC MoveSX MoveSY EOL
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
END
AutoCycCutSub1
EachRep
IF FirstCycle?
EntryMove
ELSE
IF FeedConnect?
DoCycleComment
IF CutterRadiusCompensation?
SeqC CRCOnC RapidC MoveSX MoveSY EOL
ELSE
IF SPXMove? OR SPYMove?
SeqC FeedC MoveSXYC FeedEntC EOL
END
END
ELSE
ExitMove
DoCycleComment
IF CutterRadiusCompensation?
SeqC CRCOnC RapidC MoveSX MoveSY EOL
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
END
EntryMove
END
END
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN

DrillStuff:
SeqC ZCP2
IF Repeats?
IF FirstCycle?
CoolOn
END
ELSE
CoolOn
END
EOL
GetCycle
SeqC Cycle StrtPos
SetAbs
TrackZNO# ClearancePlane2#
SetInc
'Z' FIRST SPZ#
SetAbsOrInc
Peck FeedEnt EOL
TrackZNO# FIRST SPZ# {.81.2}
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

GetStartOfSameTool:
DoPartCycleComment
DoOpComments
DoPostScript
CheckPass
RETURN

MasterSub:
IF FirstOperation?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE
IF ToolChangeAtHome?
SetHome
END
DoPartCycleComment
DoOpComments
DoPostScript
Seq 'G70' EOL
SeqC 'G75G90' EOL
SeqC Rapid StrtPos ZCP1 OpToolID ToolChng EOL
SeqC Speed SpinOn EOL
CheckPass
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE

{Finish off last Operation}

SeqC CoolOff EOL
SeqC 'M25' EOL
DoEndOpPS
SetAbsOrInc
LoadFeat
SUB# HomeX# CurOriginPosX#
SUB# HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC RapidC MoveXY EOL
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END

{Start new Operation}

Seq OpToolID ToolChng EOL
DoPartCycleComment
DoOpComments
DoPostScript
SeqC PlaneC Speed SpinOn EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC ZCP1 EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC 'M25' EOL
SeqC 'M0' EOL

{Start new Operation}

GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC ZCP1 EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC 'M25' EOL

{Start new Operation}

GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC ZCP1 EOL
ELSE

{Start new Operation}

GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
END
{IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END}
END
END
END
END {common point for all operations}
RapidF# { No Output }
IF Milling?
SeqC ZCP2C CoolOn EOL
IF AutoCycle?
IF Repeats?
IF ZShiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
IF FirstCycle?
DoCycleComment
DrillStuff
ELSE
IF RetractToCP1?
SeqC DrillOff EOL
SeqC Rapid ZCP1 EOL
DoCycleComment
SeqC StrtPos EOL
DrillStuff
ELSE
DoCycleComment
END
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqC DrillOff EOL
SeqC Rapid ZCP3 EOL
END
END
RETURN

EndPartSub:
{End of program ************************************************************}

{finish last operation}
SeqC CoolOff EOL
DoEndOpPS
SetAbs
LoadFeat
SUB# FIRST HomeX# CurOriginPosX#
SUB# FIRST HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC AbsOrInc RapidC MoveXY EOL
SeqC 'M25' EOL
IF ProgStop?
SeqC 'M0' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqC ProgStop EOL
END
END
RETURN

MPLoop:
TagInit
IF AllToolsOnePart?
EachPart
TagInc
EachOp
MasterSub
NextOp
EndPartSub
NextPart
ELSE { OneToolAllParts }
Save# Num#('2') Recall# Num#('1')
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
EachPart
TagInc
EachOp
IF GTEqual? Operation# Recall# Num#('1')
IF LTEqual? Operation# Recall# Num#('2')
IF Equal? Operation# Recall# Num#('1')
IF NOT FirstPart?

{Finish off last Operation}

IF FullUp?
SeqC CoolOff EOL
SeqC 'M25' EOL
END
{DoEndOpPS}

{Start new Operation}

GetStartOfSameTool
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF FullUp?
SeqC CoolOn EOL
END
END
END
MasterSub
END
END
NextOp
NextPart
Save# Num#('1') ADD# Recall# Num#('2') Num#('1')
END
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
StandardXZArcs
SetFlood
SetMaxRPM('10000')
SetMaxFeed('500')
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EOR EOL
IF UseComments?
IF ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts?
Save# Num#('1') Num#('1')
IF WorkFixtureOffsets?
'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'Therefore, the output will be controlled by the following values that are' EOL
'already entered in Equally Spaced Offsets Edit Fields:' EOL
'X' PartShiftX# ' Y' PartShiftY# ' Z' PartShiftZ# EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL
IF NotEqual? PartShiftX# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftY# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftZ# Num#('0')
BadMPWFOReport
END
END
END
END
EachOp
IF LastOp?
Save# Num#('3') Operation#
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
SeqC EOP EOL
Post
'E' EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END