RUETOM SPECIAL 420 ESR
Stainless
Mold Steel
Typical Anaylsis
Applications
Annealing
Heat Treating
Tempering
Precision Marshall’s RUETOM SPECIAL is a premium quality mold steel for use in
plastic molds. The grade is particularly suited for molding PVC and other corrosive
plastics. The grade offers an excellent combination of hardness, toughness,
corrosion resistance and wear resistance.
Applications for RUETOM SPECIAL include molds for corrosive plastics, molds for
abrasive and filled plastics, and molds requiring an excellent surface finish.
Heat uniformly to 1600°F and hold for two hours. Furnace cool, at a maximum rate of
30°F per hour to 1200°F, and air cool.
Preheat to 1450/1550°F. After thorough preheating, raise to 1850°F and soak one
half hour to one hour, depending on section thickness. Air cool to 150°F or until the
tool is hand warm. Temper immediately.
Double tempering is required. The tempering temperature may be varied
according to the desired hardness, but it is usually performed at 750°F.
Representative hardness levels after tempering are tabulated below.
Air cooled from 1850°F • Tempered 2 + 2 Hours
(Section Size — 4” x 4”)
Tempering Temperature (°F)
Hardness (RC)
Carbon
.40
Manganese
.80
Chromium
13.50
Silicon
.30
The Deluxe Company
400
550
750
950
1100
55
52
51
52
40
Note: Variations in section size, heating rate, soak time, quench rate and tempering will cause
deviations from the above values. Precision Marshall should be consulted for specific applications.
Deluxe Plate
RUETOM SPECIAL 420 ESR
EDM
Condition
Finish
Sizes
Electro-discharge machining is used in the production of various tooling. This
process produces recast, rehardened and retempered layers on the EDM surface.
It is recommended that RUETOM SPECIAL be stress relieved at 50°F below the final
tool tempering temperature, after the EDM process, to temper the rehardened layer
produced by EDM.
RUETOM SPECIAL 420 ESR is provided completely decarb free and stress relieved.
Ground oversize to typical rms 50/75, maximum 125.
Available in standard thickness increments 1/4” through 4”.
Deluxe Plates
MARSHALLOY MQ
®
/FM
MARSHALLOY
TM
STD 4142
PRESCO O-1
AIRTRUE A-2
DIECRAT A-6
SUPER 7 MQ
®
S-7
ARISTOCRAT D-2
FIRECHROME H-13
TRM-2 M-2
Ground Flat Stock
PRESCO O-1
AIRTRUE A-2
SUPER 7 S-7
NUTEC 42
®
4142
ARISTOCRAT D-2
MARSHALLCRAT
®
LC
Drill Rod
WATERCRAT W-1
OILCRAT O-1
AIRTRUE A-2
SUPER 7 S-7
ARISTOCRAT D-2
TRM-2 M-2
WATERCRAT W-1 Cold-drawn
The Deluxe Company’s Guarantee of Quality
Precision Marshall’s conformance to specifications is the highest in the industry.
Precision Marshall assumes complete liability for any costs directly relating to a
deviation from our published specifications. Any such costs, properly documented,
will be reimbursed.
For more information, visit our web site at www.pmsteel.com.
Additional Products
Inventory Locations
Headquarters
99 Berry Road
Washington, PA 15301
T
•
800 537 7528
F
•
800 350 1353
National Distribution Center
1 Northpoint Court
Bolingbrook, IL 60440
T
•
800 537 7528
E
•
sales@pmsteel.com
pmsteel.com
Precision Marshall Steel
The Deluxe Company
Deluxe Plate