Special Features of the 4x4

Mechanisms and accessories

Trim and upholstery

KC0L - KC0P - KC0S - KC0V

Refer to the Workshop Repair Manual for parts not mentioned in this manual. 326

77 11 306 182

"The repair methods given by the manufacturer in this document are based on the 
technical specifications current when it was prepared.

The methods may be modified as a result of changes introduced by the manufacturer 
in the production of the various component units and accessories from which his 
vehicles are constructed."

JULY 2001

All copyrights reserved by Renault.

EDITION ANGLAISE

Copying or translating, in part or in full, of this document or use of the service part 
reference numbering system is forbidden without the prior written authority of Renault.

© RENAULT 2001

Contents

Page

55 

58 

71 

EXTERIOR PROTECTION

Front bumper

55-1

Side protective mouldings

55-3

Front wing extenders  

55-5

Sill panel

55-6

UPPER INTERIOR ACCESSORIES

Storage compartment

58-1

BODY INTERNAL TRIM

Side trim panels

71-1

A
B
C
D

A

A

Mechanisms and accessories

Trim and upholstery

EXTERIOR PROTECTION

Front bumper

55

155

EXTERIOR PROTECTION

Front bumper

NOTE: The bumper is removed in the same way as on 
the basic model, only dismantling is different.

DISMANTLING

Remove: 
– the bumper,

– the bolt (A).

Release the clips (B), then remove the fog light.

Disconnect the connector.

Take out the rivets (C).

Release the clips (D), then remove the bumper trim.

Take out the rivets (E).

Release the clips (F), then remove the lower casing.

Release the clips (G), then remove the absorber.

55-1

A

EXTERIOR PROTECTION

Front bumper

55

55-2

Release:
– the clips (I) and (J), then remove the grilles,
– the clips (K), then remove the towing hitch access 

cover.

A

EXTERIOR PROTECTION

Side protective mouldings

55

55-3

Side protective mouldings

REMOVING THE FRONT DOOR MOULDING

Remove the bolt (A).

Slide the moulding towards the rear of the vehicle (1).

IMPORTANT: the indexing clips (B) cannot be 
removed without being damaged, so always fit new 
ones after removal (e.g. after a panel straightening 
operation).

B

EXTERIOR PROTECTION

Side protective mouldings

55

55-4

Release the two clips (C), then remove the badge.

REMOVING THE REAR DOOR MOULDING 

Slide the moulding towards the front of the vehicle (2).

Remove the strips as illustrated above.

SPECIAL FEATURES OF REFITTING THE FRONT 
AND REAR DOOR MOULDINGS

Position the strips on the moulding, then clip the 
moulding to the door.

NOTE: only indexing strips can be left on the panel 
while the mouldings are removed.

B

EXTERIOR PROTECTION

Front wing extenders

55

55-5

Front wing extenders  

REMOVAL

Unclip the upper section of the extender (1).

Release the three clips (A), then remove the extender.

C

EXTERIOR PROTECTION

Sill panel

55

55-6

Sill panel

REMOVAL

Remove the front wing extender.

Unclip:
– the upper section of the sill panel (1),

– the lower section of the sill panel (A).

Remove the nuts (B), then release the sill panel 
mounting.

D

UPPER INTERIOR ACCESSORIES

Storage compartment

58

158

UPPER INTERIOR ACCESSORIES

Storage compartment

REMOVAL

Remove:
– the three bolts (A),
– the four clips (B),

– the bolt (C), then release the trim.

Remove the two screws (D).

Remove the trim (E).

Remove the three screws (F).

Partially unscrew the two screws (G), then release the 
storage compartment mounting.

58-1

A

INTERIOR BODY LININGS

Side trim panels

71

171

INTERIOR BODY LININGS

Side trim panels

REMOVAL

Remove:
– the rear parcel shelf,
– the emergency spare wheel,
– the jack,

– the four fastenings (A), then release the emergency 

spare wheel support,

– the two clips (B), then release the trim (1).

71-1

A