MULTIPLE ALIGNED

COOLING SYSTEM

H40.00-52.00XM-16CH

(H1050HD-CH, 1150HD-CH) [E117, F117]

PART NO. 1568204

700 SRM 1159

SAFETY PRECAUTIONS

MAINTENANCE AND REPAIR

• When lifting parts or assemblies, make sure all slings, chains, or cables are correctly

fastened, and that the load being lifted is balanced. Make sure the crane, cables, and
chains have the capacity to support the weight of the load.

• Do not lift heavy parts by hand, use a lifting mechanism.

• Wear safety glasses.

• DISCONNECT THE BATTERY CONNECTOR before doing any maintenance or repair

on electric lift trucks. Disconnect the battery ground cable on internal combustion lift
trucks.

• Always use correct blocks to prevent the unit from rolling or falling. See HOW TO PUT

THE LIFT TRUCK ON BLOCKS in the Operating Manual or the Periodic Mainte-
nance section.

• Keep the unit clean and the working area clean and orderly.

• Use the correct tools for the job.

• Keep the tools clean and in good condition.

• Always use HYSTER APPROVED parts when making repairs. Replacement parts

must meet or exceed the specifications of the original equipment manufacturer.

• Make sure all nuts, bolts, snap rings, and other fastening devices are removed before

using force to remove parts.

• Always fasten a DO NOT OPERATE tag to the controls of the unit when making repairs,

or if the unit needs repairs.

• Be sure to follow the WARNING and CAUTION notes in the instructions.

• Gasoline, Liquid Petroleum Gas (LPG), Compressed Natural Gas (CNG), and Diesel fuel

are flammable. Be sure to follow the necessary safety precautions when handling these
fuels and when working on these fuel systems.

• Batteries generate flammable gas when they are being charged. Keep fire and sparks

away from the area. Make sure the area is well ventilated.

NOTE: The following symbols and words indicate safety information in this
manual:

WARNING

Indicates a condition that can cause immediate death or injury!

CAUTION

Indicates a condition that can cause property damage!

Multiple Aligned Cooling System

Table of Contents

TABLE OF CONTENTS

General ...............................................................................................................................................................

1

Description .........................................................................................................................................................

2

Radiator..........................................................................................................................................................

2

Radiator Cap ..................................................................................................................................................

2

Thermostat.....................................................................................................................................................

2

Water Pump ...................................................................................................................................................

3

Fan and Fan Shroud......................................................................................................................................

3

Cooling System Checks......................................................................................................................................

3

Radiator..........................................................................................................................................................

3

Thermostat.....................................................................................................................................................

3

Water Pump ...................................................................................................................................................

4

Exhaust Leaks ...............................................................................................................................................

4

Fan and Fan Shroud......................................................................................................................................

4

Cooling System Repair ......................................................................................................................................

4

Remove ...........................................................................................................................................................

4

Install .............................................................................................................................................................

5

Core Repair.........................................................................................................................................................

6

Remove ...........................................................................................................................................................

6

Install .............................................................................................................................................................

6

Radiator Cleaning ..............................................................................................................................................

7

Drain ..............................................................................................................................................................

7

Clean ..............................................................................................................................................................

7

Fill ..................................................................................................................................................................

7

Troubleshooting..................................................................................................................................................

8

This section is for the following models:

H40.00-52.00XM-16CH (H1050HD-CH, 1150HD-CH) [E117, F117]

©2005 HYSTER COMPANY

i

"THE

QUALITY

KEEPERS"

HYSTER

APPROVED

PARTS

700 SRM 1159

General

General

This section describes the total repair of the cooling
system and the individual repair of separate cooling
sections in the cooling system. See Figure 1. Proce-
dures for cleaning the radiator and troubleshooting
are also included in this section. Because each core

can be separately serviced, there will be two differ-
ent repair procedures as follows:
• Complete removal of the cooling system
• Removal of a core

1.

COVER

2.

FAN

3.

SHROUD

4.

TRANSMISSION OIL COOLER CORE

5.

HYDRAULIC OIL COOLER CORE

6.

BOTTOM PLATE

7.

BRACKET

8.

BOTTOM RADIATOR SEAL

9.

SHIELD COVER

10. TOP RADIATOR SEAL
11. PLATE
12. CHARGE AIR COOLER CORE
13. ENGINE COOLANT CORE
14. ISOLATOR
15. TOP PLATE
16. RADIATOR CAP LOCATION
17. EXPANSION TANK
18. ROD

Figure 1. Cooling Sections

1

Description

700 SRM 1159

Description

The purpose of the cooling system is to control operat-
ing temperature of the engine, transmission, brakes,
charge air, and hydraulic system. A centrifugal wa-
ter pump circulates coolant through passages in the
engine block and radiator. A thermostat is installed
in the water outlet fitting on the engine. As coolant
flows through the radiator, the fan moves air through
the radiator to help cool the system.

The coolant is a mixture of water and antifreeze. The
antifreeze prevents the coolant from freezing in cold
weather, and thereby preventing damage to the en-
gine and radiator. The antifreeze also prevents rust
and lubricates the water pump.

RADIATOR

The radiator is the heat exchanger for the cooling sys-
tem. The fan causes air to flow through the radiator
and reduces the temperature of the coolant. The aux-
iliary coolant reservoir is connected to the radiator
by two hoses and is positioned on top of the radiator.
The cooling system contains four cooling cores and
these are as follows:
• Charged Air Cooler Core
• Engine Coolant Core
• Hydraulic Oil Cooler Core
• Transmission Oil Cooler Core

When coolant in the engine coolant core is hot, the
coolant expands. During expansion, coolant moves
from the radiator to the reservoir. When coolant be-
comes cool, it contracts. The coolant in the reservoir
flows back into the radiator. This causes the radiator
to remain filled during normal operation.

RADIATOR CAP

The radiator cap is a pressure-vent type that lets the
pressure in the cooling system increase to 103 kPa
(15 psi). The pressure in the system prevents va-
por from forming in the coolant flowing to the wa-
ter pump. This action maintains the efficiency of the
water pump and the performance of the cooling sys-
tem. The increase in pressure also raises the boiling
point of the coolant mixture to approximately 125 C
(257 F) at sea level.

The radiator cap has a pressure valve and a vac-
uum valve. The pressure valve is held against its
seat by a spring. The pressure valve opens when
the pressure in the cooling system exceeds 103 kPa

(15 psi). The vacuum valve is held against its seat
by another spring. The vacuum valve opens to re-
lieve the vacuum created when the coolant temper-
ature decreases. In certain conditions, this vacuum
can cause the radiator or top hose to collapse.

THERMOSTAT

The thermostat is a device that controls coolant flow
by opening and closing to regulate coolant temper-
ature. The thermostat uses a wax pellet to control
its operation.

The wax pellet expands when it is

heated and contracts when it is cold. When heated,
the wax pellet pushes on the piston, causing the valve
in the thermostat to open. As the wax pellet cools,
it contracts and lets a spring close the valve. When
the engine is first started and the coolant is cold,
the thermostat remains closed. During this time the
coolant circulates through the engine, letting it warm
quickly. As the engine becomes warm the thermostat
opens, letting coolant circulate through the radiator.

The opening and closing of the thermostat helps keep
the coolant within the operating limits of the system.
The same thermostat is used for summer and winter
seasons. Do not operate the engine without a ther-
mostat. The engine will take longer to get warm and
may run improperly. See Figure 2.

1.

PISTON

2.

VALVE SEAT

3.

SPRING

4.

DIAPHRAGM

5.

WAX PELLET

6.

FRAME

7.

FLANGE

8.

VENT HOLE

Figure 2. Typical Thermostat

2

700 SRM 1159

Cooling System Checks

WATER PUMP

The centrifugal-type water pump is installed at the
front of the engine block. The inlet for the pump is
connected to the bottom of the radiator by a hose.
From the pump, coolant passes through the passages
in the engine block to the top of the radiator. The
thermostat controls the flow of coolant through the
engine and radiator.

FAN AND FAN SHROUD

The fan is used to provide airflow through the radia-
tor at all engine speeds. The fan is a puller-type and
can be installed on the water pump or on a separate
hub. The fan is driven by a drive belt from the engine
crankshaft.

The fan shroud ensures the airflow from the fan goes
through the core of the radiator.

Cooling System Checks

RADIATOR

WARNING

During engine operation, be careful not to
touch the fan, pulleys, or drive belts. Contact
with these parts can cause serious injury.

To check for water flow restrictions in the radiator,
run the engine until it is warm. Shut the engine OFF
and feel the radiator. The temperature must be even
across the radiator. (The radiator will be hotter near
the top radiator hose.) Cold spots on the radiator
indicate restrictions.

If the radiator has leaks, have it repaired by trained
personnel.

THERMOSTAT

WARNING

During engine operation, be careful not to
touch the fan, pulleys, or drive belts. Contact
with these parts can cause serious injury.

CAUTION

DO NOT operate the engine without a ther-
mostat. The engine and cooling system can be
damaged.

NOTE: Repair procedures for the thermostat are in
the Engine section.

1.

Remove thermostat from cooling system.

See

Figure 3.

2.

Mix solution of water with 33% antifreeze. Heat
solution to 14 C (57 F) above temperature on
thermostat.

3.

Hold thermostat with wire and put it in solution.
Stir solution. If operating correctly, thermostat
will open.

4.

Remove thermostat and put in same solution at

12 C (10 F) below temperature on thermostat.

Valve must close completely.

1.

FAN

2.

SPACER

3.

HUB/PULLEY

4.

WATER PUMP

5.

THERMOSTAT

6.

THERMOSTAT
HOUSING

Figure 3. Cooling System Components Typical

Arrangement

3

Cooling System Repair

700 SRM 1159

WATER PUMP

WARNING

During engine operation, be careful not to
touch the fan, pulleys, or drive belts. Contact
with these parts can cause serious injury.

NOTE: Repair procedures for the water pump are in
the Engine section of the Service Manual.

Run the engine until it is warm. Check the operation
of the water pump by holding the top radiator hose. If
the pump is operating, there will be pressure surges
in the hose. See Figure 3.

EXHAUST LEAKS

WARNING

During engine operation, be careful not to
touch the fan, pulleys, or drive belts. Contact
with these parts can cause serious injury.

To check for exhaust leaks into the cooling system,
use a Combustion Leak Test Kit for this purpose. Fol-
low the manufacturer’s instructions when doing the
test.

FAN AND FAN SHROUD

WARNING

During engine operation, be careful not to
touch the fan, pulleys, or drive belts. Contact
with these parts can cause serious injury.

WARNING

DO NOT try to repair a damaged fan. If a fan
has a bent blade or is cracked, install a new fan.
A damaged fan can break during use and cause
damage or serious injury.

1.

When installing fan, make sure correct spacers
are installed and mounting capscrews are tight.

2.

When installing fan shroud, make sure cor-
rect seals are on shroud.

Before tightening

capscrews, make sure clearance around circum-
ference of fan is even with shroud. Also make
sure 1/3 to 1/2 of cross-section of fan blade ex-
tends into fan shroud.

3.

Make sure WARNING labels are installed on
shroud.

Cooling System Repair

REMOVE

NOTE: For easy access to the cooling system, turn
steering wheel until steering wheel spindle is against
stop on axle to the left or right side. See Figure 4.

CAUTION

Remove the ground cable first or lift truck
damage may occur.

1.

Disconnect the cables at the battery.

2.

Remove top plates and cover plate in front of cab.

WARNING

Coolant must be at room temperature before
draining the radiator or personal injury may
occur.

3.

Put drain pan under radiator.

4.

Remove radiator cap.

Figure 4. Cooling System Access

5.

Remove drain plug and drain radiator.

4

700 SRM 1159

Cooling System Repair

6.

Disconnect charged air cooler hoses from charged
air cooler core. See Figure 1.

7.

Disconnect engine coolant hoses from engine
coolant core and expansion tank. See Figure 5.

1.

COOLANT HOSE

2.

DRAIN HOSE

3.

EXPANSION TANK

Figure 5. Engine Coolant Hoses

8.

Disconnect the drain hose from the frame of the
cooling system.

9.

Disconnect hydraulic oil lines from hydraulic oil
cooler core.

10. Disconnect transmission oil lines from transmis-

sion oil cooler core.

11. Place caps on all open lines.

WARNING

Verify cables at the battery are disconnected
when working near the fan. Sudden start of the
fan can cause serious personal injury.

12. Remove cover to access fan bolts.

13. Remove fan.

WARNING

Verify the lifting device has the rated capac-
ity to lift the cooling system or personal injury
may occur.

14. Place a lifting device just above cooling system

for support and lowering.

15. Use the lifting eyes on the cooling system and

create tension with the lifting device.

16. Remove the isolator and rod between cooling sys-

tem and the frame, located on the topside of the
cooling system.

17. Remove capscrews and rivets between bracket,

frame, bottom seal, and tanks.

18. Remove cooling system and place carefully on

ground.

INSTALL

1.

Install cooling system.

2.

Install capscrews and rivets between bracket,
frame, bottom seal, and tanks.

3.

Install the isolator and rod between cooling sys-
tem and the frame, located on the topside of the
cooling system.

4.

Install fan.

5.

Connect transmission oil lines to transmission oil
cooler core. See Figure 1.

6.

Connect hydraulic oil lines to hydraulic oil cooler
core.

7.

Install the drain hose to the frame of the cooling
system.

8.

Connect engine coolant hoses to engine coolant
core and expansion tank.

9.

Connect charged air cooler hoses to charged air
cooler core.

10. Install drain plug.

5

Core Repair

700 SRM 1159

11. Fill radiator with coolant. See the Maintenance

Schedule in the section Periodic Maintenance
8000 SRM 1154 (E117) or Periodic Mainte-
nance 8000 SRM 1237 (F117).

12. Install top plates and cover plate in front of cab.

CAUTION

Connect the power cable first or lift truck dam-
age may occur.

13. Connect the cables at the battery.

Core Repair

REMOVE

NOTE: For easy access to the cooling system, turn
steering wheel until steering wheel spindle is against
stop on axle to the left or right side. See Figure 4.

1.

Disconnect the cables at the battery.

2.

Remove top plates and cover plate in front of cab.

WARNING

Coolant must be at room temperature before
draining the radiator or personal injury may
occur.

3.

Put drain pan under radiator.

4.

Remove radiator cap.

5.

Remove drain plug and drain radiator.

6.

Disconnect the lines/hoses of the core. See Fig-
ure 1.

7.

Remove capscrews in the top and bottom plate.

NOTE: If core is positioned at the outside, remove
capscrews attached to the shroud.

8.

Loosen capscrews at left and/or right side for
easy removal of the core.

9.

Remove core.

INSTALL

1.

Install new core.

NOTE: If core is positioned at the outside, install cap-
screws attached to the shroud.

2.

Tighten capscrews at left and/or right side of the
core.

3.

Install capscrews in the top and bottom plate.

4.

Connect the lines/hoses of the core. See Figure 1.

5.

Install drain plug.

6.

Fill radiator with coolant. See the Maintenance
Schedule in the section Periodic Maintenance
8000 SRM 1154 (E117) or Periodic Mainte-
nance 8000 SRM 1237 (F117) for quantity and
antifreeze requirements.

7.

Replace radiator cap.

8.

Install top plates and cover plate in front of cab.

9.

Connect the cables at the battery.

6

700 SRM 1159

Radiator Cleaning

Radiator Cleaning

DRAIN

WARNING

DO NOT remove the radiator cap from the radi-
ator when the engine is hot. When the radiator
cap is removed, the pressure is released from
the system. If the system is hot, the steam and
boiling coolant can cause burns.

CAUTION

Disposal of lubricants and fluids must meet lo-
cal environmental regulations.

1.

Let coolant cool to room temperature. Put drain
pan under radiator. Remove radiator cap.

2.

Open drain valve or remove bottom radiator
hose. Remove drain plug from engine block to
drain engine.

CLEAN

CAUTION

Disposal of lubricants and fluids must meet lo-
cal environmental regulations.

1.

Drain cooling system. Fill cooling system with
clean water.

2.

Install radiator cap. Run engine until top radia-
tor hose is hot. Stop engine and let engine cool.

3.

Drain water from radiator. If water is dirty, fill
system with water and repeat procedure until
water is clean.

CAUTION

Follow the manufacturer’s instructions when
using a chemical radiator cleaner.

4.

If water does not clean system, replace the radi-
ator.

CAUTION

Follow the manufacturer’s instructions when
using special equipment to reverse clean the
radiator.

5.

If radiator or cooling system is very dirty or has
restriction, use reverse cleaning method. This
method uses air pressure to force water through
radiator in opposite direction of normal flow.

WARNING

Compressed air can move particles so they
cause injury to the user or to other personnel.
Make sure the path of the compressed air is
away from all personnel. Wear protective gog-
gles or a face shield to prevent injury to the
eyes.

6.

Check radiator fins. Clean exterior of radiator
with compressed air or water as needed.

FILL

1.

Install drain plug in engine block. Close drain
valve or install bottom radiator hose as needed.

WARNING

Do not use an alcohol or methanol-based an-
tifreeze.

They are flammable and can cause

personal injury or damage to the lift truck.

2.

Fill cooling system with mixture of 50% water
and 50% ethylene glycol antifreeze. Install ra-
diator cap.

The 50/50 mixture will protect the cooling system
to

37 C ( 35 F).

3.

Start and run engine until thermostat opens.
(Top radiator hose will be warm.)

7

Troubleshooting

700 SRM 1159

Troubleshooting

PROBLEM

POSSIBLE CAUSE

PROCEDURE OR ACTION

Coolant leaks.

There is a leak in the radiator.

Repair radiator.

There is a leak in a radiator hose or
coolant hose.

Install new hoses.

There is a leak from a plug or sensor
in the engine block.

Check sensors and plugs, and repair
leaks.

Water pump leaks.

Install new water pump.

Thermostat housing leaks.

Install

new

thermostat

housing.

Check for correct installation of ther-
mostat.

Cylinder head gasket is damaged.

Install new head gasket.

Cylinder head is cracked.

Install new cylinder head.

Engine block is cracked.

Install new cylinder block.

The engine is too hot during
operation.

There is not enough coolant in the
cooling system.

Check coolant level in radiator and
coolant recovery bottle. Add coolant
to correct level.

The radiator is dirty.

Drain and clean radiator. Clean ra-
diator fins with low pressure air or
water in reverse direction of normal
airflow. Be careful not to bend fins.
Refill with clean coolant.

The drive belt for water pump is not
adjusted correctly, worn, or broken.

Check water pump drive belt. Adjust
or install new belt as required.

The thermostat is wrong heat range
or does not operate correctly.

Check heat range. Install new ther-
mostat.

The cooling system has restrictions.

Drain and back-flush engine and ra-
diator. Refill with clean coolant.

The water pump is worn or damaged.

Install new water pump.

The exhaust system has restrictions.

Check exhaust system. Remove re-
strictions.

Ignition timing is not correct.

Check and adjust timing.

Exhaust leaks into coolant.

Head gasket(s) leaks.

Install new gasket(s).

Cylinder head is damaged.

Install new cylinder head.

8

TECHNICAL PUBLICATIONS

700 SRM 1159

8/05 (8/04)(7/04) Printed in United Kingdom