ISO standards for paints and varnishes


Paints and varnishes - Published standards

Standard reference

Title

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 1: Classification

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 11: Methods of conditioning before testing

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 11: Methods of conditioning before testing

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 3: Determination of liquid water permeability

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 6: Determination of carbon dioxide permeability

Paints and varnishes - Coating materials and coating systems for exterior masonry and concrete - Part 7: Determination of crack bridging properties

Paints and varnishes - Coating of aluminium and aluminium alloys for architectural purposes - Part 1: Coatings prepared from coating powder

Paints and varnishes - Water-borne coating materials and coating systems for interior walls and ceilings - Classification

Paints and varnishes - Water-borne coating materials and coating systems for interior walls and ceilings - Classification

Paints and varnishes - Powder organic coatings for galvanized or sherardised steel products for construction purposes

Coil coated metals - Test methods - Part 0: General introduction and list of test methods

Coil coated metals - Test methods - Part 1: Film thickness

Coil coated metals - Test methods - Part 10: Resistance to fluorescent UV radiation and water condensation

Coil coated metals - Test methods - Part 11: Resistance to solvents (rubbing test)

Coil coated metals - Test methods - Part 12: Resistance to scratching

Coil coated metals - Test methods - Part 13: Resistance to accelerated ageing by the use of heat

Coil coated metals - Test methods - Part 14: Chalking (Helmen method)

Coil coated metals - Test methods - Part 15: Metamerism

Coil coated metals - Test methods - Part 16: Resistance to abrasion

Coil coated metals - Test methods - Part 17: Adhesion of strippable films

Coil coated metals - Test methods - Part 18: Resistance to staining

Coil coated metals - Test methods - Part 19: Panel design and method of atmospheric exposure testing

Coil coated metals - Test methods - Part 2: Specular gloss

Coil coated metals - Test methods - Part 20: Foam adhesion

Coil coated metals - Test methods - Part 21: Evaluation of outdoor exposed panels

Coil coated metals - Test methods - Part 22: Colour difference - Visual comparison

Coil coated metals - Test methods - Part 23: Colour stability in humid atmospheres containing sulfur dioxide

Coil coated metals - Test methods - Part 24: Resistance to blocking and pressure marking

Coil coated metals - Test methods - Part 25: Resistance to humidity

Coil coated metals - Test methods - Part 26: Resistance to condensation of water

Coil coated metals - Test methods - Part 27: Resistance to humid poultice (Cataplasm test)

Coil coated metals - Test methods - Part 29: Resistance to environmental soiling (Dirt pick-up and striping)

Coil coated metals - Test methods - Part 3: Colour difference - Instrumental comparison

Coil coated metals - Test methods - Part 4: Pencil hardness

Coil coated metals - Test methods - Part 5: Resistance to rapid deformation (impact test)

Coil coated metals - Test methods - Part 6: Adhesion after indentation (cupping test)

Coil coated metals - Test methods - Part 7: Resistance to cracking on bending (T-bend test)

Coil coated metals - Test methods - Part 8: Resistance to salt spray (fog)

Coil coated metals - Test methods - Part 9: Resistance to water immersion

Paints and varnishes - Guide for the classification and selection of coating systems for wood based materials in furniture for interior use

Paints and varnishes - Laboratory method for testing the efficacy of film preservatives in a coating against fungi

Paints and varnishes - Laboratory method for testing the efficacy of film preservatives in a coating against algae

Industrial application of powder organic coatings to hot dip galvanized or sherardized steel articles [duplex systems] - Specifications, recommendations and guidelines

Paints and varnishes - Determination of non-volatile-matter content and spreading rate of coil coating materials

Paints and varnishes - Laboratory method for determination of release of substances from coatings in intermittent contact with water

Paints and varnishes and their raw materials - Temperatures and humidities for conditioning and testing (ISO 3270:1984)

Paints and varnishes - Coating materials and coating systems for exterior wood - Part 1: Classification and selection

Paints and varnishes - Coating materials and coating systems for exterior wood - Part 2: Performance specification

Paints and varnishes - Coating materials and coating systems for exterior wood - Part 3: Natural weathering test

Paints and varnishes - Coating materials and coating systems for exterior wood - Part 5: Assessment of the liquid water permeability

Paints and varnishes - Coating materials and coating systems for exterior wood - Part 6: Exposure of wood coatings to artificial weathering using fluorescent UV lamps and water

Binders for paints and varnishes - Determination of monomeric diisocyanates in isocyanate resins (ISO 10283:2007)

Paints and varnishes - Modelling of biocide release rate from antifouling paints by mass-balance calculation (ISO 10890:2010)

Plastics - Determination of the molecular mass and molecular mass distribution of polymer species by matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF-MS) (ISO 10927:2011)

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11124-1:1993)

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 2: Chilled-iron grit (ISO 11124-2:1993)

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 3: High-carbon cast-steel shot and grit (ISO 11124-3:1993)

Preparation of steel substrates before application of paints and related products - Specifications for metallic blast-cleaning abrasives - Part 4: Low-carbon cast-steel shot (ISO 11124-4:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11125-1:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution (ISO 11125-2:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 3: Determination of hardness (ISO 11125-3:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 4: Determination of apparent density (ISO 11125-4:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 5: Determination of percentage defective particles and of microstructure (ISO 11125-5:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 6: Determination of foreign matter (ISO 11125-6:1993)

Preparation of steel substrates before application of paints and related products - Test methods for metallic blast-cleaning abrasives - Part 7: Determination of moisture (ISO 11125-7:1993)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 1: General introduction and classification (ISO 11126-1:1993, including Technical Corrigenda 1:1997 and 2:1997)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 10: Almandite garnet (ISO 11126-10:2000)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 3: Copper refinery slag (ISO 11126-3:1993)

Preparation of steel substrates before application of paintsand related products - Specifications for non-metallic blast-cleaning abrasives - Part 4: Coal furnace slag (ISO 11126-4:1993)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 5: Nickel refinery slag (ISO 11126-5:1993)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 6: Iron furnace slag (ISO 11126-6:1993)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 7: Fused aluminium oxide (ISO 11126-7:1995)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 8: Olivine sand (ISO 11126-8:1993)

Preparation of steel substrates before application of paints and related products - Specifications for non-metallic blast-cleaning abrasives - Part 9: Staurolite (ISO 11126-9:1999)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 1: Sampling (ISO 11127-1:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 2: Determination of particle size distribution (ISO 11127-2:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 3: Determination of apparent density (ISO 11127-3:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 4: Assessment of hardness by a glass slide test (ISO 11127-4:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 5: Determination of moisture (ISO 11127-5:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 6: Determination of water-soluble contaminants by conductivity measurements (ISO 11127-6:1993)

Preparation of steel substrates before application of paints and related products - Test methods for non-metallic blast-cleaning abrasives - Part 7: Determination of water soluble chlorides (ISO 11127-7:1993)

Paints and varnishes - Artificial weathering and exposure to artificial radiation - Exposure to filtered xenon-arc radiation (ISO 11341:2004)

Paints and varnishes - Exposure of coatings to artificial weathering - Exposure to fluorescent UV lamps and water (ISO 11507:2007)

Colorimetry - Part 1: CIE standard colorimetric observers (ISO 11664-1:2007)

Colorimetry - Part 2: CIE standard illuminants (ISO 11664-2:2007)

Colorimetry - Part 4: CIE 1976 L*a*b* Colour space (ISO 11664-4:2008)

Colorimetry - Part 5: CIE 1976 L*u*v* Colour space and u', v' uniform chromaticity scale diagram (ISO 11664-5:2009)

Binders for paints and varnishes - Chlorinated polymerization resins - General methods of test (ISO 11668:1997)

Paints and varnishes - Determination of volatile organic compound (VOC) content - Part 1: Difference method (ISO 11890-1:2007)

Paints and varnishes - Determination of volatile organic compound (VOC) content - Part 2: Gas-chromatographic method (ISO 11890-2:2006)

Binders for paints and varnishes - Amino resins - General methods of test (ISO 11908:1996)

Binders for paints and varnishes - Polyisocyanate resins - General methods of test (ISO 11909:2007)

Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 1: Wet (salt fog)/dry/humidity (ISO 11997-1:2005)

Paints and varnishes - Determination of resistance to cyclic corrosion conditions - Part 2: Wet (salt fog)/dry/humidity/UV light (ISO 11997-2:2000)

Paints and varnishes - Determination of wet-scrub resistance and cleanability of coatings (ISO 11998:2006)

Paints and varnishes - Determination of mar resistance (ISO 12137:2011)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 1: General introduction (ISO 12944-1:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 2: Classification of environments (ISO 12944-2:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 3: Design considerations (ISO 12944-3:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 4: Types of surface and surface preparation (ISO 12944-4:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 5: Protective paint systems (ISO 12944-5:2007)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 6: Laboratory performance test methods (ISO 12944-6:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 7: Execution and supervision of paint work (ISO 12944-7:1998)

Paints and varnishes - Corrosion protection of steel structures by protective paint systems - Part 8: Development of specifications for new work and maintenance (ISO 12944-8:1998)

Paints and varnishes - Determination of reflection haze on paint films at 20 degrees (ISO 13803:2000)

Binders for paints and varnishes - Determination of the viscosity of industrial cellulose nitrate solutions and classification of such solutions (ISO 14446:1999)

Paints and varnishes - Determination of pigment content - Part 1: Centrifuge method (ISO 14680-1:2000)

Paints and varnishes - Determination of pigment content - Part 2: Ashing method (ISO 14680-2:2000)

Paints and varnishes - Determination of pigment content - Part 3: Filtration method (ISO 14680-3:2000)

Raw, refined and boiled linseed oil for paints and varnishes - Specifications and methods of test (ISO 150:2006)

Paints and varnishes - Examination and preparation of test samples (ISO 1513:2010)

Paints and varnishes - Standard panels for testing (ISO 1514:2004)

Paints and varnishes - Determination of scratch resistance - Part 1: Constant-loading method (ISO 1518-1:2011)

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 1: General method for extraction of biocides (ISO 15181-1:2007)

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 2: Determination of copper-ion concentration in the extract and calculation of the release rate (ISO 15181-2:2007)

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 3: Calculation of the zinc ethylene-bis(dithiocarbamate) (zineb) release rate by determination of the concentration of ethylenethiourea in the extract (ISO 15181-3:2007)

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 4: Determination of pyridine-triphenylborane (PTPB) concentration in the extract and calculation of the release rate (ISO 15181-4:2008)

Paints and varnishes - Determination of release rate of biocides from antifouling paints - Part 5: Calculation of the tolylfluanid and dichlofluanid release rate by determination of the concentration of dimethyltolylsulfamide (DMST) and dimethylphenylsulfamide (DMSA) in the extract (ISO 15181-5:2008)

Paints and varnishes - Determination of scratch resistance - Part 2: Variable-loading method (ISO 1518-2:2011)

Paints and varnishes - Bend test (cylindrical mandrel) (ISO 1519:2011)

Paints and varnishes - Cupping test (ISO 1520:2006)

Paints and varnishes - Pendulum damping test (ISO 1522:2006)

Paints and varnishes - Testing of formaldehyde-emitting coatings and melamine foams - Determination of the steady-state concentration of formaldehyde in a small test chamber (ISO 15234:1999)

Paints, varnishes and printing inks - Determination of fineness of grind (ISO 1524:2000)

Paints, varnishes and raw materials for paints and varnishes - Sampling (ISO 15528:2000)

Paints and varnishes - Corrosion testing by alternate immersion in and removal from a buffered sodium chloride solution (ISO 15710:2002)

Paints and varnishes - Determination of resistance to cathodic disbonding of coatings exposed to sea water (ISO 15711:2003)

Binders for paints and varnishes - Determination of turbidity (ISO 15715:2003)

Paints, varnishes and binders - Determination of MEQ value of water-based coating materials and binders (ISO 15880:2000)

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 1: Pull-off testing (ISO 16276-1:2007)

Corrosion protection of steel structures by protective paint systems - Assessment of, and acceptance criteria for, the adhesion/cohesion (fracture strength) of a coating - Part 2: Cross-cut testing and X-cut testing (ISO 16276-2:2007)

Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens - Part 1: Terms and definitions (ISO 16773-1:2007)

Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens - Part 2: Collection of data (ISO 16773-2:2007)

Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens - Part 3: Processing and analysis of data from dummy cells (ISO 16773-3:2009)

Paints and varnishes - Electrochemical impedance spectroscopy (EIS) on high-impedance coated specimens - Part 4: Examples of spectra of polymer-coated specimens (ISO 16773-4:2009)

Binders for paints and varnishes - Determination of glass transition temperature (ISO 16805:2003)

Paints and varnishes - Evaluation of sag resistance (ISO 16862:2003)

Paints and varnishes - T-bend test (ISO 17132:2007)

Paints and varnishes - Guidelines for the introduction of scribe marks through coatings on metallic panels for corrosion testing (ISO 17872:2007)

Paints and varnishes - Determination of the volatile organic compound content of low-VOC emulsion paints (in-can VOC) (ISO 17895:2005)

Binders for paints and varnishes - Gum rosin - Gas-chromatographic analysis (ISO 19334:2010)

Paints and varnishes - Determination of the scratch resistance of a coating system using a laboratory car-wash (ISO 20566:2005)

Paints and varnishes - Determination of stone-chip resistance of coatings - Part 1: Multi-impact testing (ISO 20567-1:2005)

Paints and varnishes - Determination of stone-chip resistance of coatings - Part 2: Single-impact test with a guided impact body (ISO 20567-2:2005)

Paints and varnishes - Evaluation of defects on coated surfaces using optical imaging - Part 1: General guidance (ISO 21227-1:2003)

Paints and varnishes - Evaluation of defects on coated surfaces using optical imaging - Part 2: Evaluation procedure for multi-impact stone-chipping test (ISO 21227-2:2006)

Paints and varnishes - Evaluation of defects on coated surfaces using optical imaging - Part 3: Evaluation of delamination and corrosion around a scribe (ISO 21227-3:2007)

Paints and varnishes - Evaluation of defects on coated surfaces using optical imaging - Part 4: Evaluation of filiform corrosion (ISO 21227-4:2008)

Paints and varnishes - Determination of percentage volume of non-volatile matter by measuring the non-volatile matter content and the density of the coating material, and calculation of the theoretical spreading rate (ISO 23811:2009)

Paints and varnishes - Cross-cut test (ISO 2409:2007)

Paints and varnishes - Determination of flow time by use of flow cups (ISO 2431:2011)

Binders for paints and varnishes - Linseed stand oil - Requirements and methods of test (ISO 276:2002)

Binders for paints and varnishes - Raw tung oil - Requirements and methods of test (ISO 277:2002)

Paints and varnishes - Determination of film thickness (ISO 2808:2007)

Paints and varnishes - Natural weathering of coatings - Exposure and assessment (ISO 2810:2004)

Paints and varnishes - Determination of density - Part 1: Pyknometer method (ISO 2811-1:2011)

Paints and varnishes - Determination of density - Part 2: Immersed body (plummet) method (ISO 2811-2:2011)

Paints and varnishes - Determination of density - Part 3: Oscillation method (ISO 2811-3:2011)

Paints and varnishes - Determination of density - Part 4: Pressure cup method (ISO 2811-4:2011)

Paints and varnishes - Determination of resistance to liquids - Part 1: Immersion in liquids other than water (ISO 2812-1:2007)

Paints and varnishes - Determination of resistance to liquids - Part 2: Water immersion method (ISO 2812-2:2007)

Paints and varnishes - Determination of resistance to liquids - Part 3: Method using an absorbent medium (ISO 2812-3:2007)

Paints and varnishes - Determination of resistance to liquids - Part 4: Spotting methods (ISO 2812-4:2007)

Paints and varnishes - Determination of resistance to liquids - Part 5: Temperature-gradient oven method (ISO 2812-5:2007)

Paints and varnishes - Determination of specular gloss of non-metallic paint films at 20°, 60° and 85° (ISO 2813:1994, including Technical Corrigendum 1:1997)

Paints and varnishes - Comparison of contrast ratio (hiding power) of paints of the same type and colour (ISO 2814:1973)

Paints and varnishes - Buchholz indentation test (ISO 2815:2003)

Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels (ISO 28199-1:2009)

Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 1: Relevant vocabulary and preparation of test panels - Technical Corrigendum 1 (ISO 28199-1:2009/Cor 1:2009)

Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 2: Colour stability, process hiding power, re-dissolving, overspray absorption, wetting, surface texture and mottling (ISO 28199-2:2009)

Paints and varnishes - Evaluation of properties of coating systems related to the application process - Part 3: Visual assessment of sagging, formation of bubbles, pinholing and hiding power (ISO 28199-3:2009)

Paints and varnishes - Determination of viscosity using rotary viscometers - Part 1: Cone-and-plate viscometer operated at a high rate of shear (ISO 2884-1:1999)

Paints and varnishes - Determination of viscosity using rotary viscometers - Part 2: Disc or ball viscometer operated at a specified speed (ISO 2884-2:2003)

Paints and varnishes - Corrosion protection by protective paint systems - Assessment of porosity in a dry film (ISO 29601:2011)

Plastics - Polymers/resins in the liquid state or as emulsions or dispersions - Determination of viscosity using a rotational viscometer with defined shear rate (ISO 3219:1993)

Paints and varnishes - Determination of resistance to humid atmospheres containing sulfur dioxide (ISO 3231:1993)

Paints and varnishes - Determination of the effect of heat (ISO 3248:1998)

Paints, varnishes and plastics - Determination of non-volatile-matter content (ISO 3251:2008)

Paints and varnishes - Visual comparison of the colour of paints (ISO 3668:1998)

Paints and varnishes - Print-free test (ISO 3678:1976)

Binders for paints and varnishes - Determination of saponification value - Titrimetric method (ISO 3681:1996)

Paints and varnishes - Terms and definitions (ISO 4618:2006)

Driers for paints and varnishes (ISO 4619:1998)

Paints and varnishes - Determination of resistance to filiform corrosion - Part 1: Steel substrates (ISO 4623-1:2000)

Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates (ISO 4623-2:2003)

Paints and varnishes - Determination of resistance to filiform corrosion - Part 2: Aluminium substrates (ISO 4623-2:2003/Cor.1:2005)

Paints and varnishes - Pull-off test for adhesion (ISO 4624:2002)

Binders for paints and varnishes - Determination of softening point - Part 1: Ring-and-ball method (ISO 4625-1:2004)

Binders for paints and varnishes - Determination of softening point - Part 2: Cup-and-ball method (ISO 4625-2:2004)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 1: General introduction and designation system (ISO 4628-1:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 10: Assessment of degree of filiform corrosion (ISO 4628-10:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 2: Assessment of degree of blistering (ISO 4628-2:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 3: Assessment of degree of rusting (ISO 4628-3:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 4: Assessment of degree of cracking (ISO 4628-4:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 5: Assessment of degree of flaking (ISO 4628-5:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 6: Assessment of degree of chalking by tape method (ISO 4628-6:2011)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 7: Assessment of degree of chalking by velvet method (ISO 4628-7:2003)

Paints and varnishes - Evaluation of degradation of coatings - Designation of quantity and size of defects, and of intensity of uniform changes in appearance - Part 8: Assessment of degree of delamination and corrosion around a scribe (ISO 4628-8:2005)

Binders for paints and varnishes - Determination of hydroxyl value - Titrimetric method (ISO 4629:1996)

Clear liquids - Estimation of colour by the Gardner colour scale - Part 1: Visual method (ISO 4630-1:2004)

Clear liquids - Estimation of colour by the Gardner colour scale - Part 2: Spectrophotometric method (ISO 4630-2:2004)

Paints and varnishes - Determination of resistance to humidity - Part 1: Continuous condensation (ISO 6270-1:1998)

Paints and varnishes - Determination of resistance to humidity - Part 2: Procedure for exposing test specimens in condensation-water atmospheres (ISO 6270-2:2005)

Clear liquids - Estimation of colour by the platinum-cobalt scale - Part 1: Visual method (ISO 6271-1:2004)

Clear liquids - Estimation of colour by the platinum-cobalt scale - Part 2: Spectrophotometric method (ISO 6271-2:2004)

Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 1: Falling-weight test, large-area indenter (ISO 6272-1:2011)

Paints and varnishes - Rapid-deformation (impact resistance) tests - Part 2: Falling-weight test, small-area indenter (ISO 6272-2:2011)

Paints and varnishes - Determination of hiding power - Part 1: Kubelka-Munk method for white and light-coloured paints (ISO 6504-1:1983)

Paints and varnishes - Determination of hiding power - Part 3: Determination of contrast ratio of light-coloured paints at a fixed spreading rate (ISO 6504-3:2006)

Binders for paints and varnishes - Alkyd resins - Part 1: General methods of test (ISO 6744-1:1999)

Binders for paints and varnishes - Alkyd resins - Part 2: Determination of phthalic anhydride content (ISO 6744-2:1999)

Binders for paints and varnishes - Alkyd resins - Part 3: Determination of unsaponifiable matter content (ISO 6744-3:1999)

Binders for paints and varnishes - Alkyd resins - Part 4: Determination of fatty acid content (ISO 6744-4:1999)

Paints and varnishes - Bend test (conical mandrel) (ISO 6860:2006)

Binders for paints and varnishes - Epoxy resins - General methods of test (ISO 7142:2007)

Binders for paints and varnishes - Methods of test for characterizing water-based binders (ISO 7143:2007)

Paints and varnishes - Determination of resistance to abrasion - Part 1: Rotating abrasive-paper-covered wheel method (ISO 7784-1:1997)

Paints and varnishes - Determination of resistance to abrasion - Part 2: Rotating abrasive rubber wheel method (ISO 7784-2:1997)

Paints and varnishes - Determination of resistance to abrasion - Part 3: Reciprocating test panel method (ISO 7784-3:2000)

Coating powders - Part 1: Determination of particle size distribution by sieving (ISO 8130-1:1992)

Coating powders - Part 10: Determination of deposition efficiency (ISO 8130-10:1998)

Coating powders - Part 11: Inclined-plane flow test (ISO 8130-11:1997)

Coating powders - Part 12: Determination of compatibility (ISO 8130-12:1998)

Coating powders - Part 13: Particle size analysis by laser diffraction (ISO 8130-13:2001)

Coating powders - Part 14: Terminology (ISO 8130-14:2004)

Coating powders - Part 2: Determination of density by gas comparison pyknometer (referee method) (ISO 8130-2:1992)

Coating powders - Part 3: Determination of density by liquid displacement pyknometer (ISO 8130-3:1992)

Coating powders - Part 4: Calculation of lower explosion limit (ISO 8130-4:1992, including Cor 1:1993)

Coating powders - Part 5: Determination of flow properties of a powder/air mixture (ISO 8130-5:1992)

Coating Powders - Part 6: Determination of gel time of thermosetting coating powders at a given temperature (ISO 8130-6:1992, including Amd 1:1998)

Coating powders - Part 7: Determination of loss of mass on stoving (ISO 8130-7:1992)

Coating powders - Part 8: Assessment of the storage stability of thermosetting powders (ISO 8130-8:1994)

Coating powders - Part 9: Sampling (ISO 8130-9:1992)

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 1: Rust grades and preparation grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:2007)

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 2: preparation grades of previously coated steel substrates after localized removal of previous coatings (ISO 8501-2:1994)

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 3: Preparation grades of welds, edges and other areas with surface imperfections (ISO 8501-3:2006)

Preparation of steel substrates before application of paints and related products - Visual assessment of surface cleanliness - Part 4: Initial surface conditions, preparation grades and flash rust grades in connection with high-pressure water jetting (ISO 8501-4:2006)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 11: Field method for the turbidimetric determination of water-soluble sulfate (ISO 8502-11:2006)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 12: Field method for the titrimetric determination of water-soluble ferrous ions (ISO 8502-12:2003)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 2: Laboratory determination of chloride on cleaned surfaces (ISO 8502-2:2005)

Preparation of steel substrates before application of paint and related products - Tests for the assessment of surface cleanliness - Part 3: Assessment of dust on steel surfaces prepared for painting (pressure-sensitive tape method) (ISO 8502-3:1992)

Preparation of steel substrates before application of paint and related products - Tests for the assessment of surface cleanliness - Part 4: Guidance on the estimation of the probability of condensation prior to paint application (ISO 8502-4:1993)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 5: Measurement of chloride on steel surfaces prepared for painting (ion detection tube method) (ISO 8502-5:1998)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 6: Extraction of soluble contaminants for analysis - The Bresle method (ISO 8502-6:2006)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 8: Field method for the refractometric dedetermination of moisture (ISO 8502-8:2001)

Preparation of steel substrates before application of paints and related products - Tests for the assessment of surface cleanliness - Part 9: Field method for the conductometric determination of water-soluble salts (ISO 8502-9:1998)

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 1: Specifications and definitions for ISO surface profile comparators for the assessment of abrasive blast-cleaned surfaces (ISO 8503-1:1988)

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 2: Method for the grading of surface profile of abrasive blast-cleaned steel - Comparator procedure (ISO 8503-2:1988)

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 3: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Focusing microscope procedure (ISO 8503-3:1988)

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 4: Method for the calibration of ISO surface profile comparators and for the determination of surface profile - Stylus instrument procedure (ISO 8503-4:1988)

Preparation of steel substrates before application of paints and related products - Surface roughness characteristics of blast-cleaned steel substrates - Part 5: Replica tape method for the determination of the surface profile (ISO 8503-5:2003)

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 1: General principles (ISO 8504-1:2000)

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 2: Abrasive blast-cleaning (ISO 8504-2:2000)

Preparation of steel substrates before application of paints and related products - Surface preparation methods - Part 3: Hand- and power-tool cleaning (ISO 8504-3:1993)

Tall-oil fatty acids for paints and varnishes - Specifications and test methods (ISO 8623:1997)

Test for sustained combustibility of liquids (ISO 9038:2002)

Paints and varnishes - Drying tests - Part 1: Determination of through-dry state and through-dry time (ISO 9117-1:2009)

Paints and varnishes - Drying tests - Part 2: Pressure test for stackability (ISO 9117-2:2010)

Paints and varnishes - Drying tests - Part 3: Surface-drying test using ballotini (ISO 9117-3:2010)

Corrosion tests in artificial atmospheres - Salt spray tests (ISO 9227:2006)

Paints and varnishes - Determination of the pot life of multicomponent coating systems - Preparation and conditioning of samples and guidelines for testing (ISO 9514:2005)



Wyszukiwarka

Podobne podstrony:
Exercise Standards for Testing and Training
GUIDELINES FOR WRITING AND PUBLISHING SCIENTIFIC PAPERS
Guidelines for Persons and Organizations Providing Support for Victims of Forced Migration
steel?rgoes guidelines for master and co
for love and sex (2)
Get Set for Media and Cultural Studies
Improvements in Fan Performance Rating Methods for Air and Sound
Preparing for Death and Helping the Dying Sangye Khadro
Supply chain for cheese and desserts
Conditioning for Sports and Martial Arts
Standard for COM in MASM32
For Health and Strenght
European standards for drinking water
Jig For Frame And Panel Gluing
10 129 139 New Tool Steel for Warm and Hot Forging
Supply chain for vegetables and fruits

więcej podobnych podstron