BMW 3series E90 E91

background image

Modell 3er BMW (E90 E91)

Use the board M35080 and clip smd8

 Remove the instrument and open it

 Look for the 8-pin chip M35080

 (

remove this chip)

 connect the clip with port M35080.

 Connect the clip to the chip M35080 (

red to pin 1

).

 Select in theTacho Universal

BMW

 3er/X3 E90/91  M35080 clip

 TheTacho Universal showns you the original km.

 Save the data!!!

 Go back to the menue

BMW

3er/X3 E90/91 35080-0

(erase) and wait until

Tacho Universal displays „OK“

 Select

BMW

 3er/X3 E90/91 M35080 clip

 Load the original data you saved before and write it completely to the chip

 Error message „data not equal“ can be ignored
 Select

BMW

 3er/X3 E90/91 M35080 clip

and program the new km.

 Do not install the instrument back yet! Before that, the CAS must be programmed to

“0”

 Please follow the instructions carefully!!!

E 90

E 91

Adjustment is done in 3 steps:

1. eeprom in instrument

2. CAS programming with BMW CAS connector

3. ErrorScan

background image

If the chip is 35080

V6 you must replace it by a new. This is new not

erasable generation.

background image

Modell 3series BMW (E90 E91)

Connect the cluster connector from car to port A.

(Pin1 to red)

 Remove the small fuse. The fusebox is on the passengers side behind the

glovebox. See picture.

Important: the small fuse stays removed during the complete process.

 Connect the Can Dongle with the BMW CAS cable and the cluster connector in the

car.

 Select

BMW

 3er/X3  E90/91  Cas Prog

 Follow exactly the instructions in Diga-Display, like „light on/off“

 When it asks to „remove fuse“, the big fuse must be removed

 i fit asks you to put it back, put back the big fuse

 after programming is finished, put back the small fuse

22. CAS with the BMW CAS connector

E 90

E 91

Attention:

Before you pull a fuse,

remove the key and store it away from the car!

While programming, do not open or close any doors or touch any buttons!!!

background image

3. ERRORSCAN

Connect the connector shown to the OBD2

connector and select the menue „Errorscan“.

Wait until the main menues returns.

This can take about 5 minutes!

Remove the small fuse. It stays removed

during the complete process.

If you are asked to remove or put back

fuese during programming, it is THIS fuse

3series BMW (E90/E91)

background image

Wyszukiwarka

Podobne podstrony:
SBT Electrical distribution centre E87, E90, E91, E92
BMW 3 E90 2005pl
Wywołanie ukrytego menu w OBD komputera BMW E60 E87 E90
akumulator do bmw 3 e90 318i 320i
Instruccion Montage Bluetooth Original BMW E90
akumulator do bmw 3 touring e91 318d 320d 325d 330d 330xd 3
akumulator do bmw 3 touring e91 318i 320i
BMW SERIE 3 320D E90 163 CV Programmazione, ottimizzazione e modifica centraline elettroniche auto
akumulator do bmw 3 e90 318d 320d 325d 330d 330xd 335d
akumulator do bmw 3 touring e91 325i 325xi 330i 330xi 335i
akumulator do bmw 3 e90 325i 325xi 330i 330xi 335i
39 SC DS300 R BMW 5 A 00 XX
Bmw 01 94 Business Mid Radio Owners Manual
bmw E38 E39 rozladowany akumulator halas z komory silnika
CARPROG BMW Key programmer manual
Instrukcja obsługi interfejs KKL OPEL, BMW, VAG
bmw 3 ci blad temperatury parownika
bmw E36 regulacji temperatury nie dziala

więcej podobnych podstron