plik

fIrMWare Update

To determine if a firmware update is required, please

follow these steps:

• With the camera fully charged, attach the LCD

BacPac

™

to camera and power camera on (see

attachment instructions on page 4). If the LCD

screen powers on, you have the latest firmware

and no update is needed.

• If the LCD BacPac does not power on,

then you will need to download and install

the latest firmware for your camera at:

gopro.com/firmware.

lCd BaCpaC featUres

1. Seamlessly attaches to the back of

HD HERO cameras.

2. LCD screen allows for easy visual control

of camera and settings.

3. Fast forward + fast rewind photos and video.

4. Integrated speaker for sound.

asseMBlInG yoUr lCd sCreen to Hd Hero

AttAChing LCD BACPAC to hD hERo

1. Slide hooked end of the BacPac (A) into the groove

on the right side of the camera body (B).

2. Push BacPac connector (C) into the HERO Bus port

(D) on the back of the camera.

REmoving LCD BACPAC fRom hD hERo

1. Pull back on left side of BacPac marked with the

arrow to disconnect from the HERO bus port.

2. Slide hooked end of BacPac (A) out of camera

groove (B).

SwAPPing houSing DooRS
To secure the HD HERO & LCD BacPac assembly into the

housing, you will need to replace the standard back door

with one of the included extended back doors. A total of 4

doors are supplied with the LCD BacPac; 2 waterproof

doors (standard + wrist housing models) and 2

non-waterproof doors (standard and wrist housing

models). The skeleton doors allow for better audio and

camera cooling when waterproofing is not needed.

1. 0pen the backdoor of the housing so that it is

hanging downwards.

2. Pull downwards on the backdoor until it snaps

free from the hinge.

3. Line up replacement backdoor into the hinge opening.

4. Push upwards on the backdoor until it clicks

into place.

UsInG tHe lCd BaCpaC

The camera’s default setting keeps the LCD screen

powered on. Below are options to change how the

LCD powers off.

CAmERA SEt mEnu oPtionS — LCo AnD LCf

Check Page 2, section “Firmware Update”, to ensure your

camera has the necessary firmware update for your LCD

screen. If so, proceed to Steps 1 & 2 below:

LCo (default): LCD ON. This setting keeps the LCD

screen powered on, continuously, while the camera

is on. LCD will only power off if the camera is turned

off or if you quickly press the side LCD button.

LCf: LCD OFF. This setting auto powers the LCD

screen off 60 seconds after the last camera button

press. The camera will remain on and only the LCD

will power off. If recording videos or photos, the

recording will continue uninterrupted while the

screen is powered off. A quick press of any button

will power the LCD screen back on.

tuRning LCD SCREEn on/off

1. Pressing the LCD button quickly will power the

screen on and off when in preview mode.

ADjuSt LCD SCREEn BRightnESS

1. Press and hold LCD button for 2 seconds to enter

LCD menu.

2. Press power/mode button twice to highlight

‘BRIGHTNESS’ menu button.

3. Press shutter button repeatedly to adjust brightness.

PLAyBACk PhotoS

1. Press and hold LCD button for 2 seconds to enter

LCD menu.

2. Press power/mode button once to highlight

‘PHOTO’ menu option.

3. Press shutter button and the first recorded photo

will automatically be displayed.

4. Press power/mode button to advance to the next

photo. Hold down power/mode button to fast

forward through photos.

5. Press shutter button to go back to the previous

photo. Hold down shutter button to fast reverse

through photos.

PLAyBACk viDEoS

1. Press and hold LCD button to enter LCD menu.

2. ‘VIDEO’ should already be highlighted.

3. Press shutter button and the first recorded video

will automatically start playing.

4. During video playback, press and HOLD the

power/mode button to Fast Forward the video

playback. Releasing the power/mode button will

resume normal playback.

5. During video playback, press and HOLD the shutter

button to Rewind the video playback. Releasing the

button will resume normal playback.

ADjuSt SPEAkER voLumE

1. During video playback, quickly press LCD

button repeatedly as needed to adjust the

speaker volume.

Exit viDEo oR Photo PLAyBACk moDE

1. Press and hold the LCD button for 2 seconds and

camera will switch back to normal camera mode.

IMportant safety and

HandlInG InforMatIon

WARNING: Failure to follow these safety instructions

could result in fire, electric shock, or other injury or

damage to the LCD BacPac or other property.
hAnDLing

The LCD BacPac contains sensitive components. Do not

drop, disassemble, open, crush, bend, deform, puncture,

shred, microwave, incinerate, paint, or insert foreign

objects into the LCD BacPac. Do not use the LCD BacPac

if it has been damaged—for example, if LCD BacPac is

cracked, punctured, or damaged by water.
The LCD screen is made of glass. This glass could break

if the BacPac is dropped on a hard surface without the

waterhousing or receives a substantial impact or is

crushed, bent, or deformed. If the glass chips or cracks,

do not touch or attempt to remove the broken glass.

Glass cracked due to misuse or abuse is not covered

under the warranty.

kEEPing thE LCD CLEAn

Clean LCD screen immediately if it comes into contact

with any contaminants that may cause stains, such as

ink, dyes, makeup, dirt, food, oils, and lotions. To clean

the LCD, use a soft, slightly damp, lint-free cloth. Avoid

getting moisture in openings. Don’t use window cleaners,

household cleaners, aerosol sprays, solvents, alcohol,

ammonia, or abrasives to clean LCD BacPac.

AvoiDing wAtER AnD wEt EnviRonmEntS

whEn not in houSing

When not protected in the waterhousing, do not use the LCD

BacPac in rain, or near washbasins or other wet locations.

Take care not to spill any food or liquid on the LCD BacPac.

In case the LCD BacPac gets wet, turn off and unplug from

camera before cleaning, and allow it to dry thoroughly

before using again. Do not attempt to dry the LCD BacPac

with an external heat source, such as a microwave oven or

hair dryer. Damage to the LCD BacPac caused by contact

with liquid is not covered under the warranty.
uSing ConnECtoRS AnD PoRtS

Never force a connector into a port. Check for obstruc-

tions on the port. If the connector and port don’t join with

reasonable ease, they probably don’t match. Make sure

that the connector matches the port and that you have

positioned the connector correctly in relation to the port.
kEEPing thE LCD BACPAC within

ACCEPtABLE tEmPERAtuRES

The LCD BacPac is designed to be operated in tempera-

tures between 0° C and 40° C and stored in temperatures

between 0° C and 50° C. Low-or high-temperature condi-

tions might temporarily shorten battery life or cause the

LCD BacPac to temporarily stop working properly. Avoid

dramatic changes in temperature or humidity when using

the LCD BacPac as condensation may form on or within

the LCD BacPac. When you’re using the LCD BacPac

or charging the battery, it is normal for the LCD BacPac

to get warm. The exterior of the LCD BacPac functions

as a cooling surface that transfers heat from inside the

unit to the cooler air outside.
10

Warranty

This product is guaranteed against manufacturing defects

for one (1) year from the original date of purchase.

GoPro’s sole obligation in the event of such defects

during this period is to repair or replace the defective part

or product with a comparable part or product at GoPro’s

sole discretion. Except for such replacement, the sale,

or other handling of this product is without warranty,

condition or other liability even though the defect or loss

is caused by negligence or other fault. Damage resulting

from use, accident, or normal wear and tear is not covered

by this or any warranty. GoPro assumes no liability for any

accident, injury, death, loss, or other claim related to or re-

sulting from the use of this product. In no event shall GoPro

be liable for incidental or consequential damages relating to

or resulting from the use of this product or any of its parts.

Because of possible user resealing error, this product

is not warranted against waterhousing leakage or any

resulting damage. Visit

gopro.com for more information.