Configuring IP MasqueradeLinux Network Administrators GuidePrevChapter 11. IP Masquerade and Network Address TranslationNextConfiguring IP Masquerade
If you've already read the firewall and accounting chapters, it
probably comes as no surprise that the ipfwadm,
ipchains, and iptables commands
are used to configure the IP masquerade rules as well.Masquerade rules are a special class of filtering rule. You can
masquerade only datagrams that are received on one interface that will
be routed to another interface. To configure a masquerade rule you
construct a rule very similar to a firewall forwarding rule, but with
special options that tell the kernel to masquerade the datagram. The
ipfwadm command uses the -m
option, ipchains uses -j MASQ, and iptables uses
-j MASQUERADE to
indicate that datagrams matching the rule specification should be
masqueraded.Let's look at an example.
A computing science student at Groucho Marx University has a number of
computers at home internetworked onto a small Ethernet-based local area
network. She has chosen to use one of the reserved private Internet network
addresses for her network. She shares her accomodation with other students,
all of whom have an interest in using the Internet. Because student living
conditions are very frugal, they cannot afford to use a permanent Internet
connection, so instead they use a simple dial-up PPP Internet connection.
They would all like to be able
to share the connection to chat on IRC, surf
the Web, and retrieve files by FTP directly to each of their computers—IP
masquerade is the answer.The student first configures a Linux machine to support the dial-up link and to
act as a router for the LAN. The IP address she is assigned when she dials up
isn't important. She configures the Linux router with IP masquerade and uses
one of the private network addresses for her LAN:
192.168.1.0. She ensures that each of the hosts on the
LAN has a default route pointing at the Linux router.The following ipfwadm commands are all that are required to
make masquerading work in her configuration:
# ipfwadm -F -p deny
# ipfwadm -F -a accept -m -S 192.168.1.0/24 -D 0/0
or with ipchains:
# ipchains -P forward -j deny
# ipchains -A forward -s 192.168.1.0/24 -d 0/0 -j MASQ
or with iptables:
# iptables -t nat -P POSTROUTING DROP
# iptables -t nat -A POSTROUTING -o ppp0 -j MASQUERADE
Now whenever any of the LAN hosts try to connect to a service on a
remote host, their datagrams will be automatically masqueraded by the
Linux masquerade router. The first rule in each example prevents the
Linux machine from routing any other datagrams and also adds some
security.
To list the masquerade rules you have created, use the -l
argument to the ipfwadm
command, as we described in earlier while discussing firewalls.To list the rule we created earlier we use:
# ipfwadm -F -l -e
which should display something like:
# ipfwadm -F -l -e
IP firewall forward rules, default policy: accept
pkts bytes type prot opt tosa tosx ifname ifaddress …
0 0 acc/m all ---- 0xFF 0x00 any any …
The “/m” in the output indicates this is a
masquerade rule.To list the masquerade rules with the ipchains command,
use the -L argument. If we list the rule
we created earlier with ipchains, the output will look like:
# ipchains -L
Chain input (policy ACCEPT):
Chain forward (policy ACCEPT):
target prot opt source destination ports
MASQ all ------ 192.168.1.0/24 anywhere n/a
Chain output (policy ACCEPT):Any rules with a target of MASQ are masquerade rules.Finally, to list the rules using iptables you need to use:
# iptables -t nat -L
Chain PREROUTING (policy ACCEPT)
target prot opt source destination
Chain POSTROUTING (policy DROP)
target prot opt source destination
MASQUERADE all -- anywhere anywhere MASQUERADE
Chain OUTPUT (policy ACCEPT)
target prot opt source destination
Again, masquerade rules appear with a target of MASQUERADE.Setting Timing Parameters for IP Masquerade
When each new connection is established, the IP masquerade software
creates an association in memory between each of the hosts involved in
the connection. You can view these associations at any time by
looking at the /proc/net/ip_masquerade file.
These associations will timeout after a period of inactivity, though.
You can set the timeout values using the ipfwadm command.
The general syntax for this is:
ipfwadm -M -s <tcp> <tcpfin> <udp>
and for the ipchains command it is:
ipchains -M -S <tcp> <tcpfin> <udp>The iptables implementation uses much longer default
timers and does not allow you to set them.Each of these values represents a timer used by the IP masquerade software and
are in units of seconds. The following table summarizes the timers and their
meanings:NameDescriptiontcp TCP session timeout. How long a TCP connection may remain idle before the
association for it is removed.
tcpfin
TCP timeout after FIN. How long an association will remain
after a TCP connection has been disconnected.
udp UDP session timeout. How long a UDP connection may remain idle before the
association for it is removed.
PrevHomeNextConfiguring the Kernel for IP MasqueradeUpHandling Name Server Lookups
Wyszukiwarka
Podobne podstrony:
x 087 2 masq kernel configx 087 2 masq namelookupsx 087 2 uucp config filesx 087 2 serial configurationConfigurationExceptionconfiguration change management81A290Ethereal Config Sniffingx 087 2 accounting zeroing counterconfigFreeSWAN configurationx 087 2 cnews miscconfigureconfigconfiguration management?FE6290x 087 2 cnews nfswięcej podobnych podstron