{Change Comments ***********************************************************}
{12/13/88, Added missing connect info for milling repeats, JR}
{5/26/90, Updated: Fanuc 5M M015.54 to .72.1 format, fixed MultipleParts endless loop, JR}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{9/18/90, Updated: Fanuc 5M M015.73 to .76.1 format, JR}
{4/3/91
Modified: Fanuc 5M M015.76.1
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}
{12/21/92
Modified: Fanuc 5M M015.76.1
For: Gibbs & Associates
Updated to Version 4.1 per LongHand [AbsOrInc] M001.81.2 Format.
This supports both Absolute and Incremental output.
This supports MultipleParts.
Using Var(1), Var(2) and Var(3) for logical control of MultiplePart Operations.
Using Var(4), Var(5), Var(6) and Var(7) for correct Positioning of AutoCycles that Repeat in
X and/or Y, and when AbsoluteMoves = FALSE.
DWB}
{1/13/94
Modified: Fanuc 5M M015.81.2
For: Fructus Data AB
Converted to Metric.
Changed "Inch decimalformats" to Metric decimalformats in "Def.formats"
Changed "Inch decimalformats" to Metric decimalformats in "Prog"
Changed "SetScaleFactor" to Metric 25.4 in RestoreScale
Changed "If Metric"to "If Not Metric" in RestoreScale
Changed "Inch" to "Millimeters" in ProgrComments
Mikael Bagge}
{2/17/94
Modified: Fanuc 5M M015.81.3m
For: Gibbs & Associates/Fructus
Versions: ncCad 4.32/ncCAM 4.32/ncPost 4.32.02/Compost 4.21.20
Changes made per Tom Hubina & Mikael Bagge
Deleted CloseSub command at end of Prog.
Changed PostCinc command to Post at end of Prog.
M. Bagge reported that Virtual leaves two files open.
First File contains ProgComments and EndOfFileComments.
Second File contains output inbetween.
Final EOR at end between PostCinc and Close commands was not present in either file.
DWB}
{4/27/94
Updated: Fanuc 5M M015.81.4m
For: Hillar Malm/Fructus
Versions: ncCad 4.32.03/ncCAM 4.32.03/ncPost 4.32.03/Compost 4.21.20
Updated to Version 4.2 per LongHand M001.81.3a Format.
Updated using Fanuc 5M M015.81.3 changes of 1/31/94 and 4/27/94.
Changed TrackZNO# ZDepth# to TrackZNO# FIRST SPZ# at DrillStuff.
SPZ# is affected by SetScale, whereas ZDepth# is not.
Changed logic of MPLoop sub to handle IF NewTool? and LastOp? situations.
Commented out DoEndOpPS at MPLoop for OneToolAllParts, it does not work correctly.
Added CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Added Move to ZInC for Non-AutoCycle FeedConnect Repeats with ZMoves at ExitMove sub.
Moved DoCycleComment call to before StrtPos move in related subs.
Moved SeqC and EOL outside of IF ELSE condition at ExitMove sub.
Moved SeqC AbsOrInc and EOL outside of IF ELSE condition at AutoCycCutSub2 sub.
Deleted ReSetPass2 at end of ZonlyRepAutoCycle sub.
Already executed at end of call to AutoCycCutSub2 sub.
Following changes made per Mikael Bagge of Fructus
Changed FORMATs for Addresses X, Y, Z, I, J, K, Q and R from '#####^##0;0' to '####^#0;0' in
Compost General Default Formats Dialog.
Added literal G80G92X0Y0Z0 following DoOpComments at FirstOperation.
Changed all occurances of Speed5M to TABLE(1,SpeedRPM#,1).
Changed all occurances of OfstOn to IncValue 'G45Z-0' ToolOfst.
Added SetAbs TrackZNO# ClearancePlane1# following this block to update internal register.
Added AbsOrInc following this block to restore Processor to user choice.
Moved CoolOn to OfstOn block.
Added logic to output turret index code for ToolChng at NewTool and end of Prog.
Machine stores 7 tools in turret.
M6L2 will index turret 2 places.
M6L2 will cause turret Position 6 to index to turret Position 1.
Moved SpinOff to OfstOff block at EndPartSub.
Added Preset 'X0Y0' at end of Prog.
Added literal 'G28X0Y0' at end of Prog.
Added Tool List Dump following EOR at end of Prog
DWB}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '#####.###;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
#8 = 'ą#bbbbb.bbb#'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Tag#,5)
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(RapidF#,7)
FORMAT(PartShiftX#,8)
FORMAT(PartShiftY#,8)
FORMAT(PartShiftZ#,8)
{Prog Subroutines **********************************************************}
RestoreScale:
IF NOT Metric? {CAM file is in English, tools and tool path}
SetScale('25.4') { change to Metric, this is an Metric post}
END
RETURN
DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' Tag# ' )' EOL
END
RETURN
DoCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN
PSInit: {reset flags}
RotateF
RETURN
PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN
DoPostScript:
PSInit
EachPS
SeqC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqC FeedC ZInC FeedEntC EOL
ELSE
SeqC RapidC ZInC EOL
END
RETURN
GetConnect:
IF FeedConnect?
FeedC
ELSE
RapidC
END
RETURN
ExitMove:
SeqC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN
ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN
CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN
FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC: { 4.2 }
IF LastFeat?
CRCOffC
ELSE
CRCOnC
END
RETURN
StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CkCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC CkCRC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CkCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
RETURN
ToolPath:
EACHFeat
IF PointFeat? { Drilling Only }
SeqC MoveSXYZC EOL {.80.01}
ELSE
IF RapidFeat?
IF LastFeat? AND AutoCycle? {.70}
SeqC CRCOffC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN
WFOStuff:
{ NOTE: This Post Processor does not support WorkFixtureOffsets. }
RETURN
AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
SeqC IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN
Milling:
EntryMove
ToolPath
RETURN
XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
SeqC CRCOffC GetConnect StrtPosC EOL
IF FeedConnect?
IF ZshiftOnly?
EntryMove
END
ELSE
IF FeedEntry?
SeqC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN
NoRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN
XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC GetConnect MoveSXYC EOL
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN
ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC GetConnect MoveSXYC EOL
END
AutoCycCutSub1
EachRep
IF FirstCycle?
EntryMove
ELSE
IF NOT FeedConnect?
ExitMove
END
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC GetConnect MoveSXYC EOL
END
IF NOT FeedConnect?
EntryMove
END
END
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN
DrillStuff:
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# FIRST SPZ# {.81.2}
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
GetStartOfSameTool:
DoPartCycleComment
DoOpComments
DoPostScript
CheckPass
RETURN
MasterSub:
IF FirstOperation?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE
IF ToolChangeAtHome?
SetHome
END
Seq Plane 'G80' CRCOff EOL
SeqC OpToolID EOL
SeqC ToolChng EOL
DoPartCycleComment
DoOpComments
SeqC 'G80G92X0Y0Z0' EOL
DoPostScript
SeqC TABLE(1,SpeedRPM#,1) EOL
SeqC SpinOn EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC IncValue 'G45Z-0' ToolOfst CoolOn EOL { OfstOn }
SetAbs TrackZNO# ClearancePlane1#
SeqC AbsOrInc EOL
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE
{Finish off last Operation}
SeqC CoolOff EOL
SeqC IncValue OfstOff EOL
DoEndOpPS
IF ToolChangeAtHome?
SetAbs
LoadFeat
SUB# HomeX# CurOriginPosX#
SUB# HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC AbsOrInc Rapid MoveXY SpinOff EOL
ELSE
SeqC SpinOff EOL
END
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
SeqC ProgStop EOL
END
{Start new Operation}
Seq Plane 'G80' CRCOffC EOL
SeqC OpToolID EOL
SeqC ToolChng
IF GreaterThan? Tool# LAST Tool#
IF GreaterThan? SUB# Tool# LAST Tool# Num#('1') { Do not output if only one index }
'L' SUB# Tool# LAST Tool#
END
ELSE
'L' ADD# Num#('7') SUB# Tool# LAST Tool#
END
EOL
DoPartCycleComment
DoOpComments
DoPostScript
SeqC TABLE(1,SpeedRPM#,1) EOL
SeqC SpinOn EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC IncValue 'G45Z-0' ToolOfst CoolOn EOL { OfstOn }
SetAbs TrackZNO# ClearancePlane1#
SeqC AbsOrInc EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC IncValue OfstOff EOL
SeqC SpinOff EOL
SeqC 'M00' EOL
{Start new Operation}
GetStartOfSameTool
SeqC TABLE(1,SpeedRPM#,1) EOL
SeqC SpinOn EOL
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
SeqC IncValue 'G45Z-0' ToolOfst CoolOn EOL { OfstOn }
SetAbs TrackZNO# ClearancePlane1#
SeqC AbsOrInc EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC IncValue OfstOff EOL
{Start new Operation}
GetStartOfSameTool
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SeqC TABLE(1,SpeedRPM#,1) EOL
END
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
SeqC IncValue 'G45Z-0' ToolOfst EOL { OfstOn }
SetAbs TrackZNO# ClearancePlane1#
SeqC AbsOrInc EOL
ELSE
{Start new Operation}
GetStartOfSameTool
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SeqC TABLE(1,SpeedRPM#,1) EOL
END
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
END
END
END {common point for all operations}
ResetCRCNum {.72}
RapidF# { No Output }
IF Milling?
SeqC ZCP2C EOL
IF AutoCycle?
IF Repeats?
IF ZshiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
DoCycleComment
IF FirstCycle?
DrillStuff
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqC 'G80' EOL
SeqC RapidC ZCP3C EOL
END
END
RETURN
EndPartSub:
{End of program ************************************************************}
{finish last operation}
SeqC CoolOff EOL
SeqC IncValue OfstOff SpinOff EOL
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SetAbs
LoadFeat
SUB# FIRST HomeX# CurOriginPosX#
SUB# FIRST HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC AbsOrInc Rapid MoveXY EOL
END
SeqC Preset 'X0Y0' EOL
SeqC 'G28X0Y0' EOL
SeqC ToolChng
IF GreaterThan? FIRST Tool# Tool#
IF GreaterThan? SUB# FIRST Tool# Tool# Num#('1') { Do not output if only one index }
'L' SUB# FIRST Tool# Tool#
END
ELSE
IF NotEqual? FIRST Tool# Tool#
'L' ADD# Num#('7') SUB# FIRST Tool# Tool#
END
END
EOL
IF ProgStop?
SeqC 'M00' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqC ProgStop EOL
END
END
RETURN
MPLoop:
TagInit
IF AllToolsOnePart?
EachPart
TagInc
EachOp
MasterSub
NextOp
EndPartSub
NextPart
ELSE { OneToolAllParts }
Save# Num#('2') Recall# Num#('1')
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
EachPart
TagInc
EachOp
IF GTEqual? Operation# Recall# Num#('1')
IF LTEqual? Operation# Recall# Num#('2')
IF Equal? Operation# Recall# Num#('1')
IF NOT FirstPart?
{Finish off last Operation}
IF FullUp?
SeqC CoolOff EOL
SeqC IncValue OfstOff EOL
END
{DoEndOpPS}
{Start new Operation}
GetStartOfSameTool
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SeqC TABLE(1,SpeedRPM#,1) EOL
END
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
IF FullUp?
SeqC IncValue 'G45Z-0' ToolOfst CoolOn EOL { OfstOn }
SetAbs TrackZNO# ClearancePlane1#
SeqC AbsOrInc EOL
END
END
END
MasterSub
END
END
NextOp
NextPart
Save# Num#('1') ADD# Recall# Num#('2') Num#('1')
END
END
RETURN
{Start of executable Prog **************************************************}
{setup and initializations}
InitProg
ReverseXZArcs
SetFlood
SetMaxRPM('10000')
SetMaxFeed('500')
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EOR EOL
IF UseComments?
IF ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' MILLIMETERS )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts?
IF WorkFixtureOffsets?
'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'Therefore, the output will be controlled by the following values that are' EOL
'already entered in Equally Spaced Offsets Edit Fields:' EOL
'X' PartShiftX# ' Y' PartShiftY# ' Z' PartShiftZ# EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL
END
Save# Num#('1') Num#('1')
EachOp
IF LastOp?
Save# Num#('3') Operation#
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
SeqC EOP EOL
Post
EOR EOL
EachTool
SetFlag('1')
EachOp
IF Equal? TLNum# Tool#
IF Flag?('1')
SetFlagF('1')
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
END
NextOp
NextTool
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END