FINALNI TEST answers


Refer to the exhibit. Which command will remove the static address from the MAC address table?



ALSwitch(config)# no mac-address-table entry 00e0.2917.1884 fastethernet interface 0/4 VLAN 1


ALSwitch(config)# no mac-address-table entry 00e0.2917.1884 VLAN 1 fastethernet 04


ALSwitch(config-if)# no mac-address-table entry static 00e0.2917.1884 VLAN 1 fastethernet 04


ALSwitch(config-if)# no mac-address-table static 00e0.2917.1884 VLAN 1 fastethernet 04


*** ALSwitch(config)# no mac-address-table static 00e0.2917.1884 interface fastethernet 0/4 VLAN 1





Which three statements describe full-duplex Ethernet? (Choose three.)



*** It utilizes 100% of the bandwidth in both directions.


It requires two wires.


It increases the number of broadcast domains in the network.


*** It allows data to be received and sent simultaneously.


*** It reduces the number of collisions.


It provides between 60% and 80% of the bandwidth in both directions.







Refer to the exhibit. The network has converged and Switch_6 has been elected root bridge of the STP tree. However, network traffic analysis indicates that Switch_1 would be a better root bridge. How can the network administrator make this change, assuming that the spanning-tree priorities are at the default settings?



Set the bridge priority of Switch_1 to 32,768.


Set the bridge priority of Switch_6 to 65,565.


*** Set the bridge priority of Switch_1 to 1.


Set the bridge priority of Switch_6 to 255.




Refer to the exhibit. What does "FORWARDING" mean in the command output shown?



The switch is receiving BPDUs, but not sending data frames.
The switch is participating in an election process by forwarding the BPDUs it receives.
*** The switch is sending and receiving data frames.
The switch is receiving BPDUs and populating the MAC address table, but not sending data.




The network in the exhibit is to be configured using one Class C network address. Which IP addressing plan will correctly use VLSM to provide maximum efficiency in the use of the IP addresses while meeting the user requirements shown?



195.18.4.0/26 for the 59 users
195.18.4.64/26 for the 30 users
195.18.4.176/27 for the 11 users
195.18.4.112/30 for one serial link
195.18.4.116/30 for the other serial link


195.18.4.0/26 for the 59 users
195.18.4.64/26 for the 30 users
195.18.4.96/27 for the 11 users
195.18.4.112/30 for one serial link
195.18.4.116/30 for the other serial link


*** 195.18.4.0/26 for the 59 users
*** 195.18.4.64/27 for the 30 users
*** 195.18.4.96/28 for the 11 users
*** 195.18.4.112/30 for one serial link
*** 195.18.4.116/30 for the other serial link


195.18.4.0/26 for the 59 users
195.18.4.64/27 for the 30 users
195.18.4.176/27 for the 11 users
195.18.4.192/30 for one serial link
195.18.4.194/30 for the other serial link



Refer to exhibit. Routers Central and Remote are configured using RIPv1. Both routers are sending updates about their directly connected routes. The Central router can ping the Remote router serial interface and Remote can ping the serial interface of Central. However, neither router has dynamically learned routes from the other. What is the most likely problem?



A clock rate is missing from one of the serial interfaces.


A gateway of last resort is required.


Subnets cannot be used with RIPv1.


*** VLSM is not supported by RIPv1.



What is the first step in the spanning-tree process?



elect a designated switch


use a router to locate a default gateway


*** elect a root bridge


determine the path cost of each active port on the switch




Refer to the exhibit. Which sequence of commands is required to configure switch port Fa0/11 for host A?

SW-A(config)# interface fastethernet 0/11
SW-A(config-if)# vlan 11


SW-A(config)# interface vlan 11
SW-A(config-if)# switchport mode trunk


SW-A(config)# interface vlan 11
SW-A(config-if)# switchport mode access 11


*** SW-A(config)# interface fastethernet 0/11
*** SW-A(config-if)# switchport mode access
*** SW-A(config-if)# switchport access vlan 11





Which of the following are attributes of link-state routing protocols? (Choose three.)



Periodic updates are sent every 120 seconds to neighboring routers.


Each router sends its entire routing table to neighboring routers.


*** Routers send updates when a change in the network is detected.


*** Link-state protocols converge more rapidly than distance vector protocols.


After convergence, link-state protocols use more bandwidth than distance vector protocols use.


*** Link-state protocols are less prone to routing loops than distance vector protocols.


Which Ethernet switching mode has the least latency and lowest reliability?


fast-forward


asymmetric


*** store-and-forward


fragment-free


symmetric



A network administrator asked an assistant to remove several VLANs from a switch. When the assistant entered in the no vlan 1 command an error was received. What was the cause of the error?



VLANs can not be deleted until all ports have been removed from the VLAN assignment.


VLANs can only be deleted by the user that created them.


VLAN 1 can not be deleted until another VLAN has been assigned its duties.


*** VLAN1 is the management VLAN by default and can not be deleted.


The command was not entered properly, which caused a syntax error to occur.




Refer to the exhibit. Two Catalyst switches are connected, and both switches have ports configured for the Sales and Marketing VLANs as shown. What will allow hosts on the same VLAN to communicate with one another across different switches?



STP


VTP


routing


*** trunking




Refer to the exhibit. The link between switches SW-A and SW-B needs to provide connectivity between hosts on the same VLAN across the two switches. How should these ports be configured?



as data channel ports


as access ports


*** as trunking ports


as root ports


as inter-VLAN ports




Refer to the graphic. Which of the following commands would be used on the router to provide communication between the two hosts connected to the switch?



interface vlan 2
ip address 192.168.2.1 255.255.255.0
no shutdown
interface vlan 3
ip address 192.168.3.1 255.255.255.0
no shutdown


*** interface fastethernet 0/0
*** no shutdown
*** interface fastethernet 0/0.2
*** encapsulation dot1q 2
*** ip address 192.168.2.1 255.255.255.0
*** interface fastethernet 0/0.3
*** encapsulation dot1q 3
*** ip address 192.168.3.1 255.255.255.0


interface vlan 2
switchport mode trunk dot1q
interface vlan 3
switchport mode trunk dot11


interface fastethernet 0/0
mode trunk dot1q 2 3
ip address 192.168.2.1 255.255.255.0



Which of the following features do RIPv1 and RIPv2 have in common? (Choose three.)



*** hop count as a metric


classless routing


*** use split horizon

*** maximum hop count is 15


broadcast updates


no authentication




Refer to the exhibit. What is an advantage of this network design?



It provides multiple paths for Layer 2 broadcasts to circulate through the network.


It allows spanning tree to forward traffic across redundant paths simultaneously.


It maximizes the number of ports available for users.


*** It provides multiple paths for connectivity in the event of link failure.




Why would a network administrator choose to enable authentication for OSPF exchanges? (Choose two.)




*** to prevent routing information from being falsified


to reduce OSPF information exchange overhead


to assure that OSPF routing information takes priority over RIP or IGRP updates


to encrypt routing tables to prevent unauthorized viewing


*** to ensure that routing information comes from a valid source




Which of the following statements is true when VTP is configured on a switched network that incorporates VLANs?



VTP is only compatible with the 802.1Q standard.


VTP adds to the complexity of managing a switched network.


All VTP hello packets are routed through VLAN 1 interfaces.


*** Changes made to the network can be communicated to all switches dynamically.




Refer to the exhibit. How many broadcast domains are there in the topology shown, assuming that VLANs are not configured on the switches?



one


two

*** three
four


six


eight




What does a constant amber SYSTEM LED indicate on a Catalyst switch?




The switch is going through POST.


The switch is in the process of initializing ports.


The switch has failed POST.


*** The switch has passed POST and is working properly.




Employees of XYZ Company connect their laptop computers to the office LAN using Ethernet ports. The Cisco switches used in the company network are configured with port security. At which layer of the three-layer design model do these switches operate?

physical

distribution

data link

*** access

core





Which of the following tasks must be completed to configure a router interface to serve the newly added network 192.168.10.64/27 and to advertise this network over RIP v2? (Choose three.)


*** RIP v2 must be configured with the network command and the IP network number for the new network.


RIP v2 must be configured with the network command and the IP host address and subnet mask for the newly activated interface.


The router must be configured with the ip subnet-zero command so that this network can be added and advertised.


*** A network host address and subnet mask must be applied to the newly activated interface.


*** The routing protocol must be activated with the router rip and version 2 commands.


RIP v2 must be configured on the other enterprise routers with an entry for the newly added network.




Refer to the exhibit. A company always uses the last valid IP address in a subnetwork as the IP address of the router LAN interface. A network administrator is using a laptop to configure switch SW-A with a default gateway. Assuming the switch IP address is 192.168.120.12/24, what command string will the administrator use to assign a default gateway to the switch?




SW-A(config)# ip gateway 192.168.120.1


SW-A(config)# ip route 0.0.0.0 0.0.0.0 192.168.120.255


SW-A(config)# ip route 192.168.120.254 255.255.255.0 fastethernet 0/0


SW-A(config)# ip default-route 192.168.120.254


*** SW-A(config)# ip default-gateway 192.168.120.254




Refer to the output in the exhibit. What can be determined from the information shown?



VTP has been enabled for all ports.


Hosts in VLAN11 and VLAN22 must have IP addresses in the same subnet in order for them to exchange data.


Three ports have been assigned to the management VLAN.


*** ARP requests issued by the host on port Fa0/12 will be seen by all hosts on VLAN33.




Refer to the network and command output shown in the exhibit. A network administrator located at the Headquarters site needs to check the configuration of a switch located at the Pacific office. Which command can be used to gain remote access to the Pacific LAN switch, assuming the switch is assigned the IP address 198.19.27.251/24?



Headquarters# telnet Pacific


Headquarters# dial Pacific 198.19.27.251


Headquarters(config)# line vty 0 4
Headquarters(config-line)# telnet Pacific


*** Headquarters# telnet 198.19.27.251




Performance of the network shown in the exhibit has become poor since the addition of hosts to the network. The network administrator suspects that excessive collisions are causing this problem. If the network is using hubs, what should be done to reduce the collisions?

Add a router to every hub segment.

Replace hubs with access points.

*** Replace hubs with switches.

Add additional hubs.




The following command was added to a router configuration:

ip route 172.26.153.0 255.255.255.0 198.19.27.249

What two effects will this command have? (Choose two.)



It will create a default route using the interface with the IP address 198.19.27.249 as the next hop.


The route will be marked with an "C" in the routing table.


*** It will create a static route to the 172.26.153.0/24 network.


All packets with an unknown destination address will be forwarded to the 172.26.153.0/24 network.


*** Routes to network 172.26.153.0 that are learned dynamically will not be used to route packets as long as this configuration command is in effect.



Refer to the exhibit. Router LC-1 needs to be configured to provide communication between the networks shown. Which group of commands will configure EIGRP on LC-1 to work within this network?



LC-1(config)# router eigrp 1
LC-1(config-router)# network 192.168.43.0 0.0.0.3 area 0
LC-1(config-router)# network 192.168.43.4 0.0.0.3 area 0
LC-1(config-router)# network 192.168.43.128 0.0.0.63 area 0


LC-1(config)# router eigrp 1
LC-1(config-router)# network 192.168.43.0 0.0.0.3 no-summary
LC-1(config-router)# network 192.168.43.4 0.0.0.3 no-summary
LC-1(config-router)# network 192.168.43.128 0.0.0.192 no-summary


*** LC-1(config)# router eigrp 1
*** LC-1(config-router)# network 192.168.43.0


LC-1(config)# router eigrp 1
LC-1(config-router)# network 192.168.43.0 0.0.0.3
LC-1(config-router)# network 192.168.43.4 0.0.0.3
LC-1(config-router)# network 192.168.43.128 0.0.0.192




When should EIGRP automatic summarization be turned off?



when a router has not discovered a neighbor within three minutes


when a router has more than three active interfaces


*** when a router has discontiguous networks attached


when a router has less than five active interfaces



What is the first parameter used to determine which switch is selected as the root bridge in a spanning-tree network?



highest path cost


highest priority number


highest Layer 2 address


*** lowest priority number


lowest path cost


lowest Layer 2 address




Refer to the exhibit. What is the meaning of the highlighted value of 64 shown in the routing table?




It is the administrative distance.


It is the value assigned by the Dijkstra algorithm that designates how many hops are in the network.


It is the value used by the DUAL algorithm to determine the bandwidth for the link.


*** It is the metric, which is cost.




Which two statements describe the Spanning Tree Protocol? (Choose two.)



It can only be used in networks in which routers are installed.


It can only be used in networks in which both routers and switches are used.


*** It can only be used in networks in which Layer 2 switching is in use.


*** It eliminates Layer 2 loops in network topologies.


It eliminates the need for redundant physical paths in network topologies.



Multiple routers have been configured with EIGRP as the routing protocol for use in the corporate network. What is true of the operation of this network? (Choose three.)



Only link-state protocols will run in the network.


*** Routing information in the form of partial updates will be sent in response to topology changes.


*** The network can support multiple routed protocols.


Hello packets are used to discover and verify the status of neighboring routers.


Routing updates are broadcast to all other routers in the network.


*** Routing updates that consist of entire routing tables are sent to neighboring routers.






Refer to the graphic. Switch 2 has computers attached that belong to VLAN 2. Switch 3 has computers attached that belong to VLAN 3. Switch 1 is a Cisco 2926G Layer 3 switch that has a route module installed. Switch 1 provides connectivity to the other switches and is used to route between the VLANs. At which layer of the three-layer switch design model does Switch 1 operate?



physical


data link


core


access


network


*** distribution




Refer to the exhibit. Which configuration commands will direct outbound traffic from Corp_1 to the ISP and inbound traffic from the ISP to network 192.168.1.0/24?



*** Corp_1(config)# ip route 0.0.0.0 0.0.0.0 serial 0/0
*** ISP(config)# ip route 192.168.1.0 255.255.255.0 serial 0/1


Corp_1(config)# ip route 198.19.27.0 255.255.255.0 serial 0/0
ISP(config)# ip route 0.0.0.0 0.0.0.0 serial 0/1


Corp_1(config)# ip route 0.0.0.0 0.0.0.0 serial 0/0
ISP(config)# ip route 0.0.0.0 0.0.0.0 serial 0/0


Corp_1(config)# ip route 198.19.27.0 255.255.255.0 serial 0/0
ISP(config)# ip route 192.168.1.0 255.255.255.0 serial 0/1




Refer to the graphic. The host on VLAN 2 cannot communicate with the host on VLAN 3. Which of the following could be the problem based on the output of the show interface fastethernet 0/1 command from the switch?



The switch port 1 is not set to access mode.


*** The router interface connected to switch port 1 is shut down.


The router is not configured for trunking.


The switch port is not configured for full duplex or a speed of 100 Mbps.



What do EIGRP routers use to establish and maintain adjacency relationships with neighboring routers?



the exchange of routing tables with directly attached routers

*** the exchange of hello packets with neighboring routers


the learning of new routes from neighbors


the comparison of known routes to information received in updates


the exchange of neighbor tables with directly attached routers




Refer to the OSPF network in the exhibit. Router R2 has been elected DR, but router R1 is the more powerful router. How can the network administrator configure R1 to force it to be elected as DR?



R1(config)# ospf priority 1


R1(config)# ip ospf priority 255


R1(config)# interface fastethernet 0/0
R1(config-if)# ospf priority 0


R1(config)# interface fastethernet 0/0
R1(config-if)# ip ospf priority 0


*** R1(config)# interface fastethernet 0/0
*** R1(config-if)# ip ospf priority 255




The network administrator shown in the exhibit is connected to an Ethernet LAN port on ACC-1. The administrator needs to verify the configuration of the newly installed switch ACC-3. What must be done so that the administrator can access ACC-3 with a web browser? (Choose three.)



*** Establish the Layer 3 connectivity of the host to ACC-3.


Set the password on the management VLAN.


Configure the hostname on ACC-3.
*** Activate the HTTP service on ACC-3.


*** Configure IP addressing parameters on ACC-3.




Refer to the exhibit. Each switch is shown with its MAC address. Which switch will be elected as the spanning-tree root bridge, if the switches are configured with their default priority values?

Switch_1


Switch_2
Switch_3
Switch_4


*** Switch_5


Switch_6




Refer to the exhibit. If the exhibited network is running EIGRP, which subnetworks can be assigned to the serial links between LC-1 and the other routers?



192.168.43.4/30 and 192.168.43.8/30


192.168.43.32/30 and 192.168.43.160/30


*** 192.168.43.96/30 and 192.168.43.100/30


192.168.43.160/30 and 192.168.43.164/30


192.168.43.192/30 and 192.168.43.196/30




Refer to the exhibit. What is the most efficient summarization of the routes attached to router R1?



198.18.0.0/16


198.18.48.0/21


198.18.32.0/22


198.18.48.0/23


*** 198.18.49.0/23


198.18.52.0/22




Which layer of the hierarchical three-layer design model combines traffic from multiple IDFs?



access


backbone


*** distribution


core




Refer to the exhibit. What will be the result of DR elections in the OSPF network shown? (Choose three.)



*** CTL will be DR of the 172.16.4.0/24 network.


ID3 will be DR of the 172.16.4.0/24 network.

*** CTL will be DR of the 172.16.5.0/24 network.


ID1 will be DR of the 172.16.5.0/24 network.


CTL will be DR of the 172.16.8.0/24 network.


*** ID2 will be DR of the 172.16.8.0/24 network.





Refer to the exhibit. What is the correct OSPF configuration for router RT-1?


RT-1(config)# router ospf 1
RT-1(config-router)# network 172.16.21.0 0.0.0.63 area 0
RT-1(config-router)# network 172.16.21.248 0.0.0.3 area 0


RT-1(config)# router ospf 0
RT-1(config-router)# network 172.16.21.0 0.0.0.3 area 0
RT-1(config-router)# network 172.16.21.248 0.0.0.31 area 0


*** RT-1(config)# router ospf 1
*** RT-1(config-router)# network 172.16.21.0 0.0.0.31 area 0
*** RT-1(config-router)# network 172.16.21.248 0.0.0.3 area 0


RT-1(config)# router ospf 99
RT-1(config-router)# network 172.16.21.0 255.255.255.224 area 0
RT-1(config-router)# network 172.16.21.248 255.255.255.248 area 0

Wyszukiwarka

Podobne podstrony:
Blue Fins Test Answer Key
Lucky Number Test Answer Key
01 EW Licensing Test Answers
Answer Key Language and Skills Test:B
Answer Key Practice Test 1 (1)
Answer Key Matura Test 2
Answer Key Matura Test 1
Answer Key Placement Test

więcej podobnych podstron