2b

2b



ASSEMBLE COMPONENTS TO THE PC BOARD

□ C4 - 10pF Discap


□ Q2 - 2N3904 Transistor (see Figurę A)


□ L1 - Coil


□ C5 - 12pF Discap (12)


□ C6 - 33pF Discap (33)


□ C1 - .1pF Discap (104)


□ R6 - 10k£2 5% 1/4W Res. (brown-black-orange-gold)


Top Legend of PC Board

* Mount these resistors on end.

□ R8 - 1ki2 5% 1/4W Res.* (brown-black-red-gold)

□ C7 - .001 pF Discap (102)

□ R10 - 1k£2 5% 1/4W Res.’ (brown-black-red-gold)

□ R1 - 8.2k£i 5% 1/4W Res. (gray-red-red-gold)

□ R4 - 47k£2 5% 1/4W Res. (yellow-volet-orange-gold)

□ R3 - 4.7kQ 5% 1/4W Res. (yellow-vio!et-red-gold)

□ R2 - 27kii 5% 1/4W Res. (red-violet-orange-gold)

□ Q3 - 2N3904 Transistor (see Figurę A)

□ C3 - .001pF Discap (102)

□ C2 - .1pF Discap (104)

□ Q1 - 2N3904 Transistor (see Figurę A)

□ R7 - 1.5ki2 5% 1/4W Res. (brown-green-red-gold)

□ R5 - 150£i 5% 1/4W Res.* (brown-green-brown-gold)

□ R9 - 47kii 5% 1/4W Res.* (yellow-violet-orange-gold)


Mount the transistor with the fiat side as shown on the top legend.

Figurę A



□    Strip the insulation off of one end of the 12* gray wire to expose 1/8’ of bare wire. Mount and solderthe wire to the foil side of the PC board in hole J5.

□    Cut a 1 1/2’ red wire and 11/2’ black wire. Stnp the insulation off of both ends to expose 1/8’ of bare wire. Mount and solder the red wire to the foil side of the PC board in hołd J6 (+) and the black wire to hole J7 (-•).

□    Cut the leads of the LED so that they are 1/4’ long, then spread them slightly apart (see Figurę B).

□    Solder the free end of ✓->. the black wire to the fiat side lead of the LED. Solder the free end of the red wire to the other lead of the LED.

Figurę B


Foil Side of PC Board

Black

Figurę C


□    If your microphone has leads attached to it, cut them off flush with the pads on the microphone. Cut a 2" piece of red wire and a 2’ piece of black wire. Strip the insulation off of both ends to expose 1/8' of bare wire. Solder the red wire to the foil side of the PC board in hole J1 (+) and the black wire to hole J2 (--)•

□    Solder the free end of the red wire to the (+) pad on the mic and the black wire to the (-) pad on the mic as shown in Figurę C.


-6-


Wyszukiwarka

Podobne podstrony:
2c □ Mount the slide switch onto the foil side of the PC board. The tabs on the switch must go
136 ZAąCdir* Hajn union may submit a disputc to the arbitration board, which is cqual ta gmng up thc
72 02694b4d70 CARBURETOR 1. Remove: °Carburetor assembly Refer to the "CHAPTER 5—CARBURE-TOR&qu
UNIT 5. TIME FOR DISCOVERY. Lesson 4. Plans for sum mer. L99 205 I think some of you will go to the
back to the drawing board 0    the1    Board Whenever the targct HŁjmi
Tutor3r □ Convert to Printed Circuit Board The following components were found in your
Component overlay. 01 must have sufficient leg length for it to be bent over . below the Circuit boa
Tutor3t Convert to Printed Circuit Board 3 The components can be automatically placed on the printed
a3 Warm-up This activity is intended as a lead-in to the unit. Write on the board Travel and touri
Convert2 E Convert to Printed Circuit Board The following components were found in your
Convert4 Convert to Piinted Circuit Board V Default 3 The components can be automatically placed on
Convert5 □ Convert to Printed Circuit Board The Circuit connections can be routed automatically. It
Esther Friesner ?mon Hooray for Hellywood (F) •V. tiUa    MKUMkM-UMUS. The DcYtlr
f36 2 □    Netscape: Rdd an Item to the

więcej podobnych podstron