{
MILL=F
LATHE=T
SIMPLE_ROT_POS=F
ROTARY_MILL=F
ADV_MILL=F
SUBS=F
MILLTURN_Y-AXIS=F
METRIC=F
}

{Change Comments ***********************************************************}

{9/2/92
Copied & modified: Fanuc 0T Miyano (CES) L109.82
For:Bizal Manufacturing
Control: Fanuc 0T
Machine: Puma
Updated to .82ż format
No Bar puller, changed bar puuer stuff to turrest set up stuff at beginning of output.
Changed to use Preset Hame at the beginning of each tool.
RoughContour CannedCycle:
Added "'R' CutDepth#" to 1st LCycle line it is the pull off amount for each pass.
Changed StrtPos to StrtPosC.
Deleted the decimal point from the 1st G76 threading line.
Jim Radcliffe}

{6/10/94
Modified: Fanuc 0T Puma [BM] L271.82
For: Rick Meide / Bizal Mfg
Moved tool index & CoolOn to Preset line.
Go directly to CSS at beginning of operation and stay in at end, no G97 is CSS operation!
Jim Radcliffe}

{12/11/95
Initial: Fanuc 0T Puma [BM] L271.82.1
Created: Fanuc 0T [Superior] Lxxx.82.1
ForUser: Superior Tire & Rubber Corp
Develop: ComPost 4.21.33, Catalyst68K v2.30.18C
Comment: Changed to R-Format Arcs.
Jim Radcliffe}

{1/12/96
Initial: Fanuc 0T DP [ST] L403.82.1
Created: Fanuc 0T DP [ST] L403.85.2
ForUser: Superior Tire & Rubber Corp
Control: Fanuc 0T
Machine: Puma
Develop: ComPost 4.21.33, Catalyst68K v2.30.22C
Comment: Modified per marked up readout and conversation with Tim Rowles
Deleted turret set up routine from beginning of program.
SetMaxRPM to 5000
Added SetMinRpm to 50
Moved tool and offset call to line by itself in main.
Moved tool offset offset cancel to line byitself before home move.
Changed to R format arcs.
SpinOff before reversing spindle.
Updated to .85 format per Fanuc 10T MS [-] L001.85.01.01
Jim Radcliffe}

{8/8/96
Inital: Fanuc 0T DP [ST] L403.85.2
Created: Fanuc 0T DP [HP] L497.85
For User:Howard's Precision
Removed "Home" commands form Tool chnages
JM}

{8/15/96
Modified: Fanuc 0T DP [HP] L497.85
Created: Fanuc 0T DP [HP] L497.85.1
For: Howard's Precision
Machine: Daewoo Puma 8HC
Control: Fanuc 0T-C/F..136986C
Versions: Catalyst v3.05.03C/Compost 4.21.37/v1.0b1
Changes made per Howard Altis of Howard's Precision, fax and phone call
Updated for Catalyst v3.05C per Fanuc 10T MS [-] L001.85 Format.
Moved CoolOn from FirstOperation and NewTool to Approach sub.
Deleted Spindle Direction check at CheckOffset sub.
Spindle Direction is Tool dependant, not Operation dependant.
Added OpToolID '00' CRCOff at FirstOperation and NewTool.
Moved OpToolID LatheOffset to SpinOn block at FirstOperation and NewTool.
Deleted LOfstOff '00' at NewTool.
Deleted OpToolID '00' at end of Prog.
DWB}

{2/25/97
Initial: Fanuc 0T DP [HP] L497.85.1
Created: Fanuc 0T DP [TTT] Lxxx.85
ForUser: TTT Enterprises
Control: ????
Machine: ????
Develop: ComPost2 68K 1.0b11, Virtual Gibbs 3.23
Comment: New beginning of tool per before and after edits readouts from Jim Jones.
Jim Radcliffe}

{2Dec98
Original: Fanuc 0T DP [TTT] L567.85
Created: Fanuc 0T DP [BC] Lxxx.85
For: Bettanini's Custom Mfg.
Changes made per: Tony Bettanini
Added Post Header Comment at the top of Prog.
Deleted old version numbers and comments e.g. {.62}, {commands}, {literals}, etc
Moved OpToolID LatheOffset from AppMove to FirstOperation and NewTool.
Charles Winston}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.####;0.'
#3 = '#######0'
#4 = '###^##0'
#5 = '#.######;0.'
#6 = '###0'
#7 = '#'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(MUL#,2) { Non-Canned Threading AutoFinish }
FORMAT(InFeedAngle#,2)
FORMAT(FirstMoveEPZ#,2)
FORMAT(CutDepth#,2)
FORMAT(Program#,3)
FORMAT(Operation#,3)
FORMAT(Tool#,3)
FORMAT(Dwell#,4)
FORMAT(FeedIPR#,5)
FORMAT(CalcEPRPM#,6)
FORMAT(RapidF#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags from last Op, .70}
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL
PSStuff
NextPS
RETURN

StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN

FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN

FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN

ApproachSP:
IF ApproachFace?
SeqLabC StockOnNoCan XSPC EOL
SeqLabC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqLabC FeedNoCan ZSPC FeedRateNoCan EOL
END
ELSE { ODApproach/IDApproach }
SeqLabC StockOnNoCan ZSPC EOL
SeqLabC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqLabC FeedNoCan XSPC FeedRateNoCan EOL
END
END
RETURN

AppMove:
StockOff ThisOpEntryZCP CoolOn
RETURN

Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqLabC ThisOpEntryXCP AppMove EOL
ELSE
IF ApproachID?
SeqLabC XOpCD AppMove EOL
ELSE {ApproachFace}
SeqLabC StockOnNoCan XSP AppMove EOL
END
END
ApproachSP
RETURN

CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
END
IF NewToolOffset?
SeqLabC OpToolID LatheOffset EOL
END
CSSOff
IF ConstantSurfaceFeed?
IF LAST ConstantSurfaceFeed?
IF NotEqual? MaxRPM# LAST MaxRPM#
SeqLabC Preset MaxRPM EOL
END
IF LAST ProgStop?
CSSOn 'G96' Speed
ELSE
IF NotEqual? SpeedRPM# LAST SpeedRPM#
CSSOn 'G96' Speed
END
END
ELSE
SeqLabC Preset MaxRPM EOL
CSSOn 'G96' Speed
END
ELSE
IF LAST ConstantSurfaceFeed?
'G97' Speed
ELSE
IF LAST ProgStop? {OR NewGear?}
'G97' Speed
ELSE
IF NotEqual? SpeedRPM# LAST SpeedRPM#
'G97' Speed
END
END
END
END
IF LAST ProgStop?
SeqLabC {SpeedC} SpinOn EOL
SeqLabC CoolOn EOL
ELSE
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
DoPostScript
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC:
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
IF LastFeat?
CRCOffC { Exit Length Feature }
ELSE
CRCOnC { Entry Length Feature }
END
END
RETURN

ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
END
ELSE
IF CannedCycle?
SeqLab
END
END
END
IF PointFeat?
SeqLabC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqLabC RapidC MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqLabC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqLabC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqLabC 'G32' MoveXC MoveZC ThrdLead EOL
Rapid
END
END
END
END
END
NEXTFeat
RETURN

CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
RapidC
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
SetAbs
PosSideLathe
StandardXZArcs
SetMaxRPM('5000')
SetMinRPM('50')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ABSOLUTE INCHES )' EOL
END
END
RestoreScale
OpenSub
StockOff
SetHome
DoOpComments
DoPostScript
Plane
SeqLab Rapid
IF ConstantSurfaceFeed?
Preset MaxRPM EOL
SeqLabC
END
OpToolID LatheOffset EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF NewTool?

{Finish off last Operation}

StockOff
CheckRapid
IF LAST ApproachOD?
SeqLabC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
END
SeqLabC LAST OpExitZCPC EOL
DoEndOpPS
SeqLabC NewHome EOL
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
IF CWSpindle? AND LAST NOT CWSpindle?
SeqLabC SpinOff EOL
ELSE
IF LAST CWSpindle? AND NOT CWSpindle?
SeqLabC SpinOff EOL
END
END
SeqLabC ProgStop EOL
END

{Start new Operation}

DoOpComments
DoPostScript
SeqLab Rapid
IF ConstantSurfaceFeed?
Preset MaxRPM EOL
SeqLabC
END
OpToolID LatheOffset EOL
SeqLabC
IF ConstantSurfaceFeed?
CSSOn 'G96'
ELSE
CSSOff 'G97'
END
Speed SpinOn EOL
Approach
ELSE
IF SameTool?

{Start new Operation}

StockOff
DoOpComments
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqLabC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqLabC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC LAST OpExitXCPC EOL
END
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqLabC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
END
SeqLabC LAST OpExitZCPC EOL
SeqLabC XOpCDC EOL
END
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqLabC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqLabC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqLabC LAST XOpECDC EOL
END
SeqLabC LAST OpExitZCPC EOL
END
END
END
CheckOffset
ApproachSP
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
SeqLabC LCycle
IF ApproachFace?
'Z' FirstMoveEPZ# XatFinZ
ELSE
XatFinZ FinZ
END
XTapAtZ FeedRate EOL
SimpleRough
ELSE
TagInc
SetPass2
IF RoughContour?
SeqLabC LCycle CutDepth 'R' CutDepth# EOL
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft FeedRate EOL
'>' Tag# EOL
SeqLab StepMove StrtPosC EOL
ELSE
IF RoughPatternShift?
SeqLabC LCycle XminusU ZminusW NumCuts EOL
SeqLabC LCycle 'PÅ‚' Tag# 'Q²' Tag# XStkLeft ZStkLeft FeedRate EOL
'>' Tag# EOL
SeqLab Rapid StrtPos EOL
END
END
ToolPath
'<' Tag# EOL
IF AutoFinish?
SeqLabC 'G70' 'PÅ‚' Tag# 'Q²' Tag# EOL
END
SetPass1
TrackXNO# CycleStartX#
TrackZNO# CycleStartZ#
END
ELSE
IF Threading?
IF Chamfer?
SeqLabC 'M23' EOL
END
SeqLabC 'G76P030060Q0015R00005' EOL
SeqLabC LCycle XatFinZ FinZ XTapAtZ CutMethod ThrdHeight CutDepth ThrdLead ToolAngle EOL
IF AutoFinish?
SeqLabC 'G92' XatFinZ FinZ XTapAtZ ThrdLead EOL
END
IF Chamfer?
SeqLabC 'M24' EOL
END
ELSE
IF Drilling?
IF Tap?
SeqLabC LCycle ZDepth 'E' FeedIPR# EOL
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed InverseSpinOn EOL
SeqLabC ZSP EOL
ELSE
IF PeckChipBreaker?
SeqLabC LCycle ZDepth RLevel Dwell Peck Retract FeedRate EOL
SeqLabC DrillOff EOL
IF AutoFinish?
SeqLabC Feed ZDepth EOL
IF Dwell?
SeqLabC 'G4P' Dwell# EOL
END
SeqLabC Rapid ZSP EOL
END
END
END
ELSE
IF Grooving?
StockOn
SetPass1
SeqLabC StrtPos EOL
ToolPath
END
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish? { .82.1c }
StockOff
IF Turning?
IF ApproachFace?
SeqLabC RapidC ZOpECPC EOL
ELSE
SeqLabC RapidC XOpECDC EOL
END
ApproachSP
SeqLabC StockOff StrtPosC EOL
ToolPath
ELSE
IF Roughing? AND NOT RoughSimple?
SetPass2
SeqLabC RapidC XSPC ZSPC EOL
SeqLabC StockOff StrtPosC EOL
ToolPath
SetPass1
ELSE
IF Threading?
SeqLabC 'X' MUL# Num#('2') ADD# FinishXRadius# Taper# EOL
SeqLabC 'G32'
IF Taper?
XatFinZ
END
FinZ ThrdLead EOL
SeqLabC Rapid XSP EOL
SeqLabC ZSP EOL
END
END
END
END
END
IF Drilling? AND Tap?
SeqLabC SpinOff EOL
SeqLabC 'G4P2000' EOL
SeqLabC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
RapidC
END
IF ApproachOD?
SeqLabC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqLabC XOpECDC EOL
END
END
SeqLabC OpExitZCPC EOL
DoEndOpPS
SeqLabC CoolOff EOL
SeqLabC FirstHome SpinOff EOL
SeqLabC UnTool '00' EOL
IF ProgStop?
SeqLabC 'M0' EOL
END
SeqLabC EOP EOL
Post
EOR EOL
Close
Retag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END