Download pattern
150 Hat  Instructions
Head circumference, 56 and 58 cm Sewing:
(221D 4" and 23") Please note: When basting and stitching
seams, the right fabric sides must be
Materials: facing. Tie-off the beginnings and
Cotton-linen blend, 150 cm (59") wide: ends of seams with backstitching.
0.40 m (16").
Vilene/Pellon G 740, 90 cm (36") wide: Hat side: Stitch narrow edges to-
0.65 m (26"). gether, right side facing in. Press seam
Grosgrain/petersham ribbon, 1.5 cm (5D 8") open and finish edges of allowances.
wide: 0.65 m (26"). Topstitch close to both sides of seam,
Piece of leather for hat band, approx. thereby catching allowances.
75 x 5 cm (30 x 2"). 1 buckle with prong, Loops: Fold fabric strip in half length-
bar width 1.5 cm (5D 8"). 3 metal eyelets, wise, right side facing in. Stitch 1.5 cm
approx. 3 mm (1D 8") inner Ø. 1 rivet. Glue (5D 8") from fold edge. Do not cut threads
Pattern pieces 1 to 3
stick (Pritt, Uhu). Sewing thread. too short. Thread threads through eye
of darning needle and knot to secure.
Recommended fabric: Fabrics with some Push needle, eye end first, through fab-
body. ric tube to turn right side out. Press
strip. Topstitch close to long edges. Cut
Printing paper pattern (for DIN A / into 4 equal pieces. Pin loops to hat
81D 4" x 115D 8" paper): side as marked on pattern piece and at
The pattern pieces are printed on 4 Cutting: seam.
sheets, each framed by a thin line. Wait The cutting layouts below show how Stitch crown piece to upper edge of
until all sheets have been printed. Lay the pattern pieces should be laid on the hat side, right sides facing. Finish edges
the sheets in the correct positions (see fabric. Make sure that the straight of allowances together.
extra sheet with the overview of the grain line marked on each pattern Brim: Lay brim pieces together, right
printed sheets). piece lies parallel to the selvages or sides facing. Stitch together along outer
Cut each sheet along the thin lines at the fold of the fabric. edges. Trim seam allowances. Turn brim
the top and right edges. Begin with the right side out. Press seamed edge. Top-
lower left sheet and glue all sheets to- Seam and hem allowances: stitch 5 mm (3D 16") from seamed edge.
gether, exactly on the thin lines Now Use a ruler and tailor's chalk to mark the Stitch brim to lower edge of hat side,
cut out the pattern pieces. following seam and hem allowances on right sides facing. Trim allowances to
Important: Seam and hem allowances the fabric, along the edges of the paper 5 mm (3D 16") wide and finish edges to-
are not included on the pattern pieces. pattern pieces: 1.5 cm (5D 8") at all seams gether. Pin grosgrain/petersham ribbon
and edges. to seam allowance of brim to meet
Choose the pattern size according to the stitching Overlap ends of ribbon and
circumference of your head. Cotton-linen blend: turn under end which lies on top. Edge-
1 Crown 1x stitch ribbon in place. Turn ribbon to-
2 Side, on fold 1x ward hat side.
3 Brim, on fold 2x Turn ends of each loop under and edge-
a) Fabric strip for 4 loops, 30 cm (12") stitch to hat side as marked.
Cutting layout
long, 6 cm (21D 2") wide (incl. allowances). Hat band: Fold leather strip in half
Cotton-linen blend,150 cm wide
lengthwise, wrong side facing in, and
Leather: glue layers together. Cut one end to a
Hatband, 70 cm (273D 4") long, 3 cm (11D 4") point. Topstitch close to all edges. Punch
Cut from a
wide (incl. allowances). a small hole for the buckle prong, 2 cm
double layer
(3D 4") from straight end. Fold straight end
of fabric,
Interfacing: over bar of buckle and hold it in place
right side All pieces which are shaded gray in with one rivet.
facing in. the cutting layout must also be cut Insert one metal eyelet 5 cm (2") from
from interfacing, along the same pointed end, then insert 2 more eyelets,
straight grain as indicated for the spaced 1.5 cm (5D 8") apart.
fabric pieces. Iron interfacing to the Run hat band through loops and buckle
wrong sides of fabric pieces. closed.
burda Download, Instructions for Hat 150 / burda World of Fashion 2/2009