{Change Comments ***********************************************************}

{5/20/93
Copied & modified: Fanuc 10M M008.81.2
For: Haas Automation
Combined OpToolID and ToolChng on one block at FirstOperation and NewTool.
Combined DoWFONum Speed SpinOn AbsOrInc Rapid StrtPos and OfstOn on one block at FirstOperation,
NewTool and SameTool.
Added CkCRC sub to cancel CutterRadiusCompensation on LastFeature of ToolPath.
Added literal 'G74' for Left-Handed Tapping at Drilling.
Moved Canned Drill Cycle Block to Main Program when Repeats = TRUE at Drilling.
Main program will output the Canned Drill Cycle, and the SubPrograms will contain only the
positions from the second feature on.
DWB}

{8/2/93
Modified: Haas M573.81.2
For: Haas Automation
Changes made per visit with Harold Moon at Haas Automation.
Added ProgramName$ to SubID block at StartSub.
Added blank lines between subs.
Deleted RepLab OnePart at OpenMP.
Moved Rapid, Feed and Connect Commands to be output in front of AbsOrInc on same block.
Deleted colons from all Comments.
Deleted Spaces following '(, and preceeding )' from ProgramNameComment at FirstOperation.
Changed Seq to 'N' Tool# EOL at FirstOperation and NewTool, output on block by itself.
Changed Safe Start block from G17G80G40 to G0G90G54G40G80G17 at FirstOperation and NewTool.
Changed StrtPos block from DoWFONum Speed SpinOn AbsOrInc Rapid StrtPos OfstOn to
Rapid AbsOrInc DoWFONum StrtPos Speed SpinOn at FirstOperation and NewTool.
Added PlaneC to StrtPos block at NewTool.
Moved OfstOn to beginning of CoolOn block at FirstOperation and NewTool.
Changed DoWFONum PlaneC AbsOrInc Rapid to Rapid AbsOrInc DoWFONum PlaneC at SameTool StrtPos block.
Added IF RetractToCP1 boolean at SameTool.
This is to force output of ZCP1 or ZCP2 for Drilling.
Changed RapidC ZCP3C to Rapid ZCP3 at Drilling.
Moved 'G80' to Rapid ZCP3 at Drilling.
Added literal 'M19', Spindle Orient, at OfstOff block at end of Prog.
Added MasterOp/CallMasterOp PostScript Command support for Drilling.
Routines have been added to call previously created subroutines.
Added MasterOpF and CallMasterOpF at PSInit.
Added PostScript Comments regarding MasterOp and CallMasterOp Commands.
Added support of MasterOp and CallMasterOp Commands at Drilling.
Added FORMAT for Recall# to output called sub.
DWB}

{9/19/95
Copied: Haas M573.81.2 & modified to HAAS (SMAC) M---.--.-
Set max RPM to 12000 and max Feed to 3000. Added tool change and comment to 'N' Tool#.
Set WFO numbers to run from G110 to G139, allowing 30 fixture offsets instead of 6.
Removed duplicate prep. codes from set up blocks. Remove 'R' Format Arcs. Removed some Comments.
Removed all M5's and added M19 to all OfstOff comands.
Sent Y axis to machine zero and changed to first tool at end of program.
KC}

{10/24/96
Modified: Haas (SMAC) M857.10
Created: Haas [HA] MZ67.13
For: Haas Automation
Versions: Catalyst v3.09C/Compost 4.21.37/v1.0b1
Changes made per Paul Cross of Haas Automation.
Updated for Catalyst v3.05C per Fanuc 6M M001.13.1 Format
Changed First Work Fixture Offset from G110 to G54 in Compost2 Origins and Values Dialog.
Changed Last Work Fixture Offset from G130 to G59 in Compost2 Origins and Values Dialog.
Added FeedEntC for SameTool Operations at EntryMove sub.
Commented out ResetCRCNum at ToolPath sub.
Customer only wants it output when it changes.
Added condition to output 'G' NewWFO# for FirstOperation or when changed via PostScript at WFOStuff
sub.
Moved SafeStart block from FirstOp2 sub to FirstOp1 sub.
Moved OpToolID ToolChng to separate block at FirstOp1 and NewToolOp3 subs.
Added AbsOrInc Rapid to StrtPos block at FirstOp3 sub.
Deleted SafeStart block at NewToolOp3 sub.
Changed Plane to PlaneC at NewToolOp3 sub.
Added AbsOrInc Rapid DoWFONum to StrtPos block at NewToolOp5 sub.
Added condition to output OperationIDComment for FirstOperation or NewTool only at DoOpComments.
DWB}

{3/31/97,
Initial: Haas [HA] MZ67.13
Created: Haas [TI] Mxxx.13
For: Tobar Industries
Changed M98 sub call to M97,
Changed Sub program# label to N,
MPK}

{15May97
Original: Haas [TI] MY55.13
Created: Haas [TI] MY55.13.1
For: Tobar Industries
Changes made per: Dan Wormuth
Moved SafeStart block in FirstOp1 and NewToolOp3 to output after DoOpComments
Added WFOStuff StrtPos Speed SpinOn to FirstOp1 and NewToolOp3
Moved Speed SpinOn from FirstOp3 to FirstOp2
Moved Speed SpinOn from NewToolOp3 to NewToolOp4
Charles Winston}

{17May97
Original: Haas [TI] MY55.13.1
Created: Haas [TI] MY55.15
For: Tobar Industries
Updated to .15 format per Fanuc 6M M001.15
MPK}

{22May97
Original: Haas [TI] MY55.15
Created: Haas [TI] Mxxx.15 Longhand
For: Tobar Industries
Updated to Longhand format per LongHand M001.12
Charles Winston}

{Prog Numeric Format Definitions ****}

#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*#####.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
#8 = 'Ä…#bbbb.bbbb#'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ADD#,4)
FORMAT(TrackZNO#,4)
FORMAT(ToolDiameter#,4)
FORMAT(Recall#,5)
FORMAT(Tag#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)
FORMAT(PartShiftX#,8)
FORMAT(PartShiftY#,8)
FORMAT(PartShiftZ#,8)

{Testing Subroutines *}

#20 = 'Ä…0000.0000'
FORMAT(OriginShiftPX#,20)
FORMAT(OriginShiftPY#,20)
FORMAT(OriginShiftPZ#,20)
FORMAT(OriginUnshiftPX#,20)
FORMAT(OriginUnshiftPY#,20)
FORMAT(OriginUnshiftPZ#,20)
FORMAT(OriginUSPXCTP#,20)
FORMAT(OriginUSPYCTP#,20)
FORMAT(OriginUSPZCTP#,20)

Report:
IF MultipleParts? AND WorkFixtureOffsets?
SetStatusOff
' ' EOL
' PartShiftX# = ' PartShiftX# ' '
' PartShiftY# = ' PartShiftY# ' '
' PartShiftZ# = ' PartShiftZ# EOL
'OriginUnshiftPX#(0) = ' OriginUnshiftPX#('0') ' '
'OriginUnshiftPY#(0) = ' OriginUnshiftPY#('0') ' '
'OriginUnshiftPZ#(0) = ' OriginUnshiftPZ#('0') EOL
'OriginUnshiftPX#(1) = ' OriginUnshiftPX#('1') ' '
'OriginUnshiftPY#(1) = ' OriginUnshiftPY#('1') ' '
'OriginUnshiftPZ#(1) = ' OriginUnshiftPZ#('1') EOL
'OriginUnshiftPX#(2) = ' OriginUnshiftPX#('2') ' '
'OriginUnshiftPY#(2) = ' OriginUnshiftPY#('2') ' '
'OriginUnshiftPZ#(2) = ' OriginUnshiftPZ#('2') EOL
' OriginShiftPX# = ' OriginShiftPX# ' '
' OriginShiftPY# = ' OriginShiftPY# ' '
' OriginShiftPZ# = ' OriginShiftPZ# EOL
' OriginUSPXCTP#(0) = ' OriginUSPXCTP#('0') ' '
' OriginUSPYCTP#(0) = ' OriginUSPYCTP#('0') ' '
' OriginUSPZCTP#(0) = ' OriginUSPZCTP#('0') EOL
' OriginUSPXCTP#(1) = ' OriginUSPXCTP#('1') ' '
' OriginUSPYCTP#(1) = ' OriginUSPYCTP#('1') ' '
' OriginUSPZCTP#(1) = ' OriginUSPZCTP#('1') EOL
' OriginUSPXCTP#(2) = ' OriginUSPXCTP#('2') ' '
' OriginUSPYCTP#(2) = ' OriginUSPYCTP#('2') ' '
' OriginUSPZCTP#(2) = ' OriginUSPZCTP#('2') EOL
' ' EOL
SetStatusOn
END
RETURN

{Prog Subroutines ****}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' Tag# ' )' EOL
END
RETURN

DoCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF FirstOperation? OR NewTool?
IF OperationIDComment?
'( OPERATION ' Operation# ' ' OperationType$ ' )' EOL
END
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
RestoreScale
END
RETURN

DoToolComment:
IF UseComments?
IF ToolComment?
'( ' ToolComment$ ' )' EOL { EOL needed here }
END
END
RETURN

DoProgramComment:
IF UseComments?
IF ProgramNameComment?
'(' ProgramName$ ')'
END
END
RETURN

BadMPWFOReport:
SetStatusOff
' ' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
'Ä„ NOTE: Even though you have elected to Ä„' EOL
'Ä„ process this file using Multiple Ä„' EOL
'Ä„ Parts with Work Fixtures, there exist Ä„' EOL
'Ä„ non-zero values in the invisible, Ä„' EOL
'Ä„ Equally SpacedÉ fields, as follows: Ä„' EOL
'Ä„ Ä„' EOL
'*****************************************' EOL
IF NotEqual? PartShiftX# Num#('0')
' X axis shift = ' PartShiftX# EOL
END
IF NotEqual? PartShiftY# Num#('0')
' Y axis shift = ' PartShiftY# EOL
END
IF NotEqual? PartShiftZ# Num#('0')
' Z axis shift = ' PartShiftZ# EOL
END
'*****************************************' EOL
'Ä„ Ä„' EOL
'Ä„ Please reset these values to zero as Ä„' EOL
'Ä„ they affect the coordinate values Ä„' EOL
'Ä„ output, starting with Part# 2. Ä„' EOL
'Ä„ Thank You. Ä„' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
' ' EOL
SetStatusOn
RETURN

PSInit:
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff:
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF
END
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC FeedC ZInC FeedEntC EOL
ELSE
SeqC RapidC ZInC EOL
END
RETURN

ExitMove:
SeqC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN

ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN

CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
SetFlag('1') { CRCOffsetC }
CRCOnC
END
END
RETURN

FormatLine:
ckCRC FeedC MoveXYZC
RETURN

ckCRCNum:
IF Flag?('1')
SetFlagF('1')
CRCOffsetC
END
RETURN

ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat? { Drilling Only }
SeqC MoveSXYZC EOL
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatLine FeedRateC ckCRCNum EOL
DecelMove2
END
SeqC FormatLine DecelFeed ckCRCNum EOL
ELSE
SeqC FormatLine FeedRateC ckCRCNum EOL
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN

AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
IF Repeats? AND ZShiftOnly?
EntryMove
END
SeqC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN

Milling:
EntryMove
ToolPath
RETURN

XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
CRCOffC
IF FeedConnect?
IF SPXMove? OR SPYMove?
SeqC FeedC MoveSXYC FeedEntC EOL
END
IF ZShiftOnly?
EntryMove
END
ELSE
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
IF FeedEntry?
SeqC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN

NoRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN

XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN

ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC RapidC MoveSXYC EOL
END
AutoCycCutSub1
EachRep
IF NOT FirstCycle?
IF FeedConnect?
SeqC AbsOrInc EOL
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
ELSE
AbsOrInc
ExitMove
DoCycleComment
IF SPXMove? OR SPYMove?
SeqC IncValue MoveSXYC EOL
AbsOrInc
END
IF FeedEntry? AND NOT FIFO?
SeqC ZCP2 EOL
END
END
EntryMove
SeqC IncValue EOL
END
EntryMove
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN

DrillStuff:
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# FIRST SPZ# {.81.2}
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('12000')
IF Metric?
SetMaxFeed('75000')
ELSE
SetMaxFeed('3000')
END
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

OpGuts:
RapidF# { No Output }
IF Milling?
SeqC ZCP2C EOL
IF AutoCycle?
IF Repeats?
IF ZShiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
DoCycleComment
IF FirstCycle?
DrillStuff
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
SetDrillEndOpZ
SeqC Rapid 'G80' ZCP3 EOL
END
END
RETURN

WFOStuff:
IF MultipleParts? AND WorkFixtureOffsets? AND NewWFO?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS AND WORK FIXTURE OFFSETS' EOL
ELSE
IF NewWFO?
SeqC 'G' NewWFO# EOL
ELSE
IF MultipleParts? AND WorkFixtureOffsets? AND NOT SameTool?
FORMAT(ADD#,5)
SeqC 'G' ADD# NewWFO# SUB# Tag# Num#('1') EOL
FORMAT(ADD#,4)
ELSE
IF NeedWFO1? AND NOT SameTool?
SeqC 'G' NewWFO# EOL
END
END
END
END
RETURN

ResetWFO:
IF WorkFixtureOffsets?
SeqC WFO1 EOL
END
RETURN

InitOp:
EOR EOL
ProgID1 DoProgramComment EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT ' FormatName$ ' )' EOL
END
END
OpenSub
RestoreScale
RETURN

FirstOp1:
SeqC Plane CRCOff 'G80' AbsOrInc Rapid EOL
'N' Tool# EOL
SeqC OpToolID ToolChng EOL
DoPartCycleComment DoToolComment DoOpComments
DoPostScript
RETURN

FirstOp2:
SeqC Speed SpinOn EOL
RETURN

FirstOp3:
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC OfstOn CoolOn EOL
RETURN

FirstOp3a: {can't XY position before WFO}
CheckPass
SeqC OfstOn EOL
SeqC CoolOn EOL
RETURN

NewToolOp1:
SeqC CoolOff EOL
IF AbsoluteMoves?
SeqC IncValue OfstOff 'M19' EOL { Spindle Orient }
SeqC AbsValue EOL
ELSE
SeqC OfstOff 'M19' EOL { Spindle Orient }
END
RETURN

NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SetAbs
LoadFeat
SUB# HomeX# CurOriginPosX#
SUB# HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC Rapid MoveXY SpinOff EOL
ELSE
SeqC SpinOff EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN

NewToolOp3:
'N' Tool# EOL
SeqC OpToolID ToolChng EOL
DoPartCycleComment DoToolComment DoOpComments
SeqC Rapid Plane CRCoff DrillOff AbsOrInc EOL
DoPostScript
RETURN

NewToolOp4:
SeqC Speed SpinOn EOL
RETURN

NewToolOp5:
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC OfstOn CoolOn EOL
RETURN

NewToolOp5a:
CheckPass
SeqC OfstOn EOL
SeqC CoolOn EOL
RETURN

SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
IF AbsoluteMoves?
SeqC IncValue OfstOff 'M19' EOL { Spindle Orient }
SeqC AbsValue EOL
ELSE
SeqC OfstOff 'M19' EOL { Spindle Orient }
END
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
IF AbsoluteMoves?
SeqC IncValue OfstOff 'M19' EOL { Spindle Orient }
SeqC AbsValue EOL
ELSE
SeqC OfstOff 'M19' EOL { Spindle Orient }
END
END
END
RETURN

SameToolOp2: {Start new Operation}
DoPartCycleComment
DoOpComments
DoPostScript
CheckPass
RETURN

SameToolOp3: {Start new Operation}
IF LAST ProgStop?
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC SpinOn EOL
SeqC OfstOn CoolOn EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF NewToolOffset?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN

End1:
SeqC CoolOff EOL
IF AbsoluteMoves?
SeqC IncValue OfstOff 'M19' EOL { Spindle Orient }
SeqC AbsValue EOL
ELSE
SeqC OfstOff 'M19' EOL { Spindle Orient }
END
RETURN

End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SetAbs
LoadFeat
SUB# FIRST HomeX# CurOriginPosX#
SUB# FIRST HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqC Rapid MoveXY SpinOff EOL
ELSE
SeqC SpinOff EOL
END
IF ProgStop?
SeqC 'M0' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqC ProgStop EOL
END
END
RETURN

End3:
SeqC 'G28Y0' EOL
SeqC PreTool ToolChng EOL
SeqC EOP EOL
EOR EOL
Post
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

MPallTools1P: {Multiple Parts, All Tools 1 Part}
IF FirstOperation?
IF FirstPart?
InitOp
END
OpenMP
FirstOp1
WFOStuff
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN

MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
WFOStuff
FirstOp2
OpenMP
FirstOp3
END
ELSE
IF NewTool?
IF FirstPart?
NewToolOp1
CloseMP
ResetWFO
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
OpenMP
NewToolOp5
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN

MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
IF FirstOperation?
IF FirstPart?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp3
OpenMP
END
ELSE
IF NewTool?
IF FirstPart?
CloseMP
NewToolOp1
ResetWFO
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
OpenMP
END
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END
OpGuts
RETURN

NoMPs: {no multiple parts}
IF FirstOperation?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
WFOStuff
SameToolOp3
END
END
OpGuts
RETURN

MasterSub:
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
RETURN

EndPartSub:
{End of program ************************************************************}

{finish last operation}
IF MultipleParts?
IF AllToolsOnePart?
End1
End2
CloseMP
ELSE {implied OneToolAllParts?}
IF FullUp?
End1
CloseMP
ResetWFO
End2
ELSE {implied ExitClearancePlane?}
CloseMP
End1
ResetWFO
End2
END
END
ELSE {NoMPs}
End1
End2
END
RETURN

DoNewPart:
IF NOT FirstPart?

{Finish off last Part}

IF FullUp?
SeqC CoolOff EOL
IF AbsoluteMoves?
IncValue
END
SeqC OfstOff EOL
END
{DoEndOpPS}

{Start new Part}

DoPartCycleComment
DoOpComments
DoPostScript
WFOStuff
CheckPass
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF FullUp?
SeqC OfstOn EOL
SeqC CoolOn EOL
END
END
RETURN

DoParts:
TagInit
EachPart
TagInc
EachOp
IF AllToolsOnePart?
MasterSub
ELSE { OneToolAllParts }
IF GTEqual? Operation# Recall# Num#('1') { Tool First Op }
IF LTEqual? Operation# Recall# Num#('2') { Tool Last Op }
IF Equal? Operation# Recall# Num#('1') { Tool First Op }
DoNewPart
END
MasterSub
END
END
END
NextOp
IF AllToolsOnePart?
EndPartSub
END
NextPart
RETURN

GetToolFirstOp:
Save# Num#('2') Recall# Num#('1')
RETURN

GetToolLastOP:
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
RETURN

MPLoop:
IF AllToolsOnePart?
DoParts
ELSE { OneToolAllParts }
GetToolFirstOp
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
GetToolLastOP
DoParts
Save# Num#('1') ADD# Recall# Num#('2') Num#('1') { Next Tool First Op }
END
END
RETURN

{Start of executable Prog, Top Level ****}

ProgStart {setup and initializations}

IF MultipleParts?
IF WorkFixtureOffsets?
{'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'Therefore, the output will be controlled by the following values that are' EOL
'already entered in Equally Spaced Offsets Edit Fields:' EOL
'X' PartShiftX# ' Y' PartShiftY# ' Z' PartShiftZ# EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL}
IF NotEqual? PartShiftX# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftY# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftZ# Num#('0')
BadMPWFOReport
END
END
END
END
EachOp
IF FirstOperation?
Save# Num#('1') Operation#
ELSE
IF LastOp?
Save# Num#('3') Operation#
END
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
ELSE
ResetWFO
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
End3