75 Engine Hood and Door

background image

75094–01

B57104

Centering Bolt

Standard Bolt

B56577

8 (0.31)



1.5 (0.059)

4.9 (0.193)



1.5 (0.059)

4 (0.16)



1.5 (0.059)

0



1.5 (0.059)

mm (in.)

B57103

ENGINE HOOD/DOOR

HOOD

75–1

2681

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

HOOD

ADJUSTMENT

HINT:
Since the centering bolt is used as a hood hinge set bolt and
hood lock set bolt, the hood and hood lock can not be adjusted
with it on. Substitute a bolt with washer for the centering bolt.

1.

INSPECT HOOD SUB–ASSY

(a)

Check that the clearance is within the standard value.

2.

ADJUST HOOD SUB–ASSY

(a)

Adjust the hood by loosening the hood side hinge bolts.
Torque: 26 N

m (265 kgf

cm, 19 ft

lbf)

background image

B55933

B55991

Clip

B55938

75–2

ENGINE HOOD/DOOR

HOOD

2682

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

(b)

Adjust the hood by turning the cushions.

(c)

Using a screwdriver, remove the hood lock release lever
cover.

HINT:
Tape the screwdriver tip before use.
NOTICE:
Removing the protector damages the clips inside the pro-
tector, and therefore the use of a new protector is neces-
sary on installation.

(d)

Adjust the lock by loosening the bolts.

background image

75095–01

B51135

ENGINE HOOD/DOOR

HOOD SUPPORT ROD

75–3

2683

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

HOOD SUPPORT ROD

REPLACEMENT

1.

REMOVE HOOD SUPPORT ROD

(a)

Using a screwdriver to hold the left spring, disengage the
upper and lower parts of the support rod, and then re-
move the hood support rod.

NOTICE:
Removal should be done while the hood is being held up.

2.

INSTALL HOOD SUPPORT ROD

NOTICE:



Install a metal socket onto the hood except a resinous one onto the body.



After the installation, make sure that the socket is securely attached.

background image

75096–01

B51104

100 mm

(4 in.)

A

B

75–4

ENGINE HOOD/DOOR

HOOD SUPPORT ROD

2684

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

DISPOSAL

1.

DISPOSE HOOD SUPPORT ROD

(a)

Fix the

hood stay assembly, with the piston–rod pulled

out, on a vise.

(b)

With protection glasses on, cut a part between A and B
as shown in the illustration with a metal saw to release the
gas.

NOTICE:
Although the gas inside the hood stay assembly is color-
less, odorless and harmless, there is a possibility that cut-
ting tips of the metal saw would jump around, therefore
cover it with clothes or something.

background image

75098–01

B56419

Power Window Regulator
Master Switch Assy

Front Door Lower Frame
Bracket Garnish

Front Door Inside Handle
Bezel Plug

Front Door Inside Handle

Front Door Trim Board Sub–assy



Front Door Service Hole Cover

Front No.1 Speaker Assy

Front Door Glass Sub–assy

Front Door Window Regulator Sub–assy

Power Window Regulator
Motor Assy

Front Door Glass Run

Front Door Glass Run No.2

Front Door Window
Front Bar Sub–assy

Front Door Frame Sub–assy Rear Lower

Front Door Outside
Handle Cover

Front Door w/ Motor Lock Assy

Front Door Handle Assy Outside

Door Outside Handle
Sub–assy

Front Door Weatherstrip

Outer Rear View
Mirror Assy

Front Door Belt Moulding Assy



Non–reusable part

ENGINE HOOD/DOOR

FRONT DOOR

75–5

2685

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

FRONT DOOR

COMPONENTS

background image

75097–01

B50717

Centering Bolt

Standard Bolt

B56580

0



1.5 (0.059)

4.5 (0.177)



1.5 (0.059)

5.6 (0.220)



1.5 (0.059)

5.1 (0.201)



1.5 (0.059)

0



1.5 (0.059)

mm (in.)

B55941

75–6

ENGINE HOOD/DOOR

FRONT DOOR

2686

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

ADJUSTMENT

HINT:
In the RH side, work in the same procedure as in the LH side.

HINT:
Since the centering bolt is used as a door hinge set bolt, the
door can not be adjusted with it on. Substitute a bolt with washer
for the centering bolt.

1.

INSPECT FRONT DOOR PANEL SUB–ASSY LH

(a)

Check that the clearance is within the standard value.

2.

ADJUST FRONT DOOR PANEL SUB–ASSY LH

(a)

Using SST, adjust the door by loosening the body side
hinge bolts.
SST

09812–00010

Torque: 26 N

m (265 kgf

cm, 19 ft

lbf)

background image

B55942

B55939

ENGINE HOOD/DOOR

FRONT DOOR

75–7

2687

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

(b)

Adjust the door by loosening the door side hinge bolts.
Torque: 26 N

m (265 kgf

cm, 19 ft

lbf)

(c)

Adjust the striker position by slightly loosening the striker
mounting screws, and hitting the striker with a brass bar
and hammer.

(d)

Tighten the striker mounting screws again.
Torque: 23 N

m (235 kgf

cm, 17 ft

lbf)

background image

75099–01

B56607

Clip

Clip

B56608

Clip

Clip

B56609

Clip

B56610

Clip

75–8

ENGINE HOOD/DOOR

FRONT DOOR

2688

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

OVERHAUL

HINT:



Installation is in the reverse order of the removal. But the installation is indicated only when it has a
point.



In the RH side, work in the same procedure as in the LH side.

1.

REMOVE POWER WINDOW REGULATOR MASTER
SWITCH ASSY

(a)

Remove the front door armrest base cover lower.

(b)

Remove the screw.

(c)

Using a screwdriver, remove the power window regulator
master switch assembly then disconnect the connector.

HINT:
Tape the screwdriver tip before use.

2.

REMOVE FRONT DOOR LOWER FRAME BRACKET
GARNISH LH

(a)

Using a screwdriver, remove the front door lower frame
bracket garnish.

HINT:
Tape the screwdriver tip before use.

3.

REMOVE FRONT DOOR INSIDE HANDLE BEZEL
PLUG LH

(a)

Using a screwdriver, remove the front door inside handle
bezel plug.

HINT:
Tape the screwdriver tip before use.

4.

REMOVE FRONT DOOR TRIM BOARD SUB–ASSY LH

(a)

Remove the hole plug.

(b)

Remove the 5 screws.

(c)

Remove the clip.

(d)

Using a screwdriver, remove the front door trim board.

HINT:
Tape the screwdriver tip before use.
(e)

Remove the inside handle then disconnect the 2 cables
from the front door lock assembly.

background image

B56611

ENGINE HOOD/DOOR

FRONT DOOR

75–9

2689

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

5.

REMOVE FRONT DOOR SERVICE HOLE COVER LH

(a)

Disconnect each connector and remove the front door service hole cover.

NOTICE:
Remove the remaining tape on the body side.
6.

REMOVE FRONT NO.1 SPEAKER ASSY

(a)

Disconnect the connector.

(b)

Remove the 4 bolts and the front No.1 speaker assembly.

7.

REMOVE FRONT DOOR GLASS SUB–ASSY LH

HINT:
Insert a shop rag inside the door panel to prevent scratching the
glass.
(a)

Open the door glass until the bolts appear in the service
hole.

(b)

Remove the 2 bolts and door glass.

NOTICE:
Do not damage the door glass.
HINT:
Pull the glass upward to remove it.

8.

REMOVE FRONT DOOR WINDOW REGULATOR SUB–ASSY LH

(a)

Disconnect the connector.

(b)

Loosen the temporarily installed bolt.

NOTICE:
When the temporarily installed bolt is removed, the front door window regulator might drop and be
deformed.
(c)

Remove the 5 bolts and front door window regulator.

9.

REMOVE POWER WINDOW REGULATOR MOTOR ASSY LH

(a)

Using a torx wrench (T25), remove the 3 screws and the motor assembly.

10.

REMOVE FRONT DOOR GLASS RUN LH

11.

REMOVE FRONT DOOR GLASS RUN NO.2

12.

REMOVE FRONT DOOR FRAME SUB–ASSY FRONT LOWER LH

(a)

Remove the 2 screws and front door frame front lower.

13.

REMOVE FRONT DOOR FRAME SUB–ASSY REAR LOWER LH

(a)

Remove the screw and front door frame rear lower.

background image

B56612

B56613

B57102

75–10

ENGINE HOOD/DOOR

FRONT DOOR

2690

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

14.

REMOVE FRONT DOOR OUTSIDE HANDLE COVER
LH

(a)

Remove the hole plug

(b)

Using a torx wrench (T30), loosen the screw and remove
the front door outside handle cover with the door lock key
cylinder installed.

15.

REMOVE FRONT DOOR W/MOTOR LOCK ASSY LH

(a)

Disconnect the connector.

(b)

Using a torx wrench (T30), remove the 3 screws and the front door w/ motor lock assembly.

16.

REMOVE FRONT DOOR HANDLE ASSY OUTSIDE LH

(a)

Pushing the outside handle in the arrow mark direction in
the illustration, remove the front door outside handle.

17.

REMOVE DOOR OUTSIDE HANDLE SUB–ASSY LH

(a)

Using a torx wrench (T30), loosen the screw.

(b)

Using pliers, disengage the clips and remove the front
door outside handle, as shown in the illustration.

NOTICE:
Be sure to remove the outside handle together with the
clips, because the clips will be damaged if the clips remain
attached to the door panel.

18.

REMOVE FRONT DOOR WEATHERSTRIP LH

(a)

Using a screwdriver, remove the door weatherstrip.

HINT:
Tape the screwdriver tip before use.
19.

REMOVE OUTER REAR VIEW MIRROR ASSY LH

(a)

Remove the 3 nuts.

(b)

Disconnect the connector then remove the outer rear view mirror assembly.

background image

B56614

ENGINE HOOD/DOOR

FRONT DOOR

75–11

2691

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

20.

REMOVE FRONT DOOR BELT MOULDING ASSY LH(See page

76–9

)

21.

INSTALL DOOR OUTSIDE HANDLE SUB–ASSY LH

(a)

Using a torx wrench (T30), install the front door outside handle sub–assy.

22.

INSTALL FRONT DOOR W/MOTOR LOCK ASSY LH

(a)

Install a new door lock wire harness packing.

NOTICE:



If reusing the removed lock with rear door motor, the packing in the connecting part should be
replaced with a new one.



Be careful that grease and dirt will not stick to the packing surface in the connecting part.



Reusing the removed packing or using a damaged packing will cause water to penetrate
through the connecting part, and it will result in a malfunction of the door lock.

(b)

Insert the outside handle link into the lock assembly with front door motor, and then set it to the door
panel.

NOTICE:
Make sure that the outside handle link is securely engaged with the lock assembly.
(c)

Using a torx wrench (T30), install the front door lock assembly with the 3 screws.

23.

INSTALL FRONT DOOR OUTSIDE HANDLE COVER
LH

(a)

Using a torx wrench (T30), install the front door outside
handle cover with the screw.

24.

INSTALL POWER WINDOW REGULATOR MOTOR ASSY LH (W/ JAM PROTECTION)

(a)

Apply MP grease to the sliding and rotating parts of the regulator assembly.

(b)

If the jam protection dose not function properly, perform the following procedure.

HINT:
It is necessary to reset the power window motor (in the initial position for the limit switch) when separating
the window regulator from the power window motor or operating the window regulator with the door glass
not installed.

(1)

Remove the power window motor.

HINT:
Place the matchmarks on the power window motor and window regulator gear.

(2)

Connect the power window motor and power window switch to the wire harness of the vehicle.

(3)

Turn the ignition switch ON and operate the power window switch to idle the power window motor
in the up side direction for more than 6 rotations or less than 10 rotations (4 seconds or more).

(4)

Assemble the power window motor and regulator.

HINT:



Install the motor when the regulator arm is below the middle point.



Align the matchmarks on the power window motor and window regulator gear when installing the pow-
er window motor.

background image

B56615

Tape

75–12

ENGINE HOOD/DOOR

FRONT DOOR

2692

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

(5)

Assemble the power window regulator and door glass.

HINT:
Never rotate the motor to the down direction until the installation of the window glass is completed.
25.

INSTALL FRONT DOOR WINDOW REGULATOR SUB–ASSY LH

(a)

Install the temporarily installed bolt securely.

(b)

Install the temporarily installed bolt to the window regulator to the front door panel, and install the front
door window regulator temporarily.

(c)

Tighten the 5 bolts and the temporarily installed bolt.

(d)

Disconnect the connector.

26.

INSTALL FRONT DOOR GLASS SUB–ASSY LH

(a)

Install the front door glass with the 2 bolts.

HINT:
When the installation point of the front door glass does not match, adjust the regulator position by manual
operation.

(1)

Connect the power window switch to the wire harness and turn the ignition switch ON.

(2)

Repeat UP and DOWN operation several times manually.

(3)

Check if AUTO UP

AUTO DOWN operates in the automatic operation.

HINT:



Note that the jam protection function does not operate just after resetting.



Reset the regulator again when performing the reverse operating after closing the window fully by
AUTO UP operation.

27.

INSPECT POWER WINDOW FUNCTION(See page

70–1

)

28.

INSTALL FRONT DOOR SERVICE HOLE COVER LH

(a)

Install a new service hole cover to the door panel.

HINT:



When installing the service hole cover, pull out the links
and connectors through the service hole cover.



There should be no wrinkles or folds on the service hole
cover after attaching it.



After attaching the service hole cover, sealing condition
should be confirmed.

background image

7509A–01

B56616

Power Window Regulator
Switch Assy

Rear Door Inside Handle
Bezel Plug

Rear Door Inside Handle

Rear Door Trim Board Sub–assy

Rear Door Service
Hole Cover

Rear Door Glass
Weatherstrip Inner

Rear Door Glass Run

Rear Door Weatherstrip

Rear Door Belt Moulding Assy

Rear Door Window Division Bar
Sub–assy

Rear Door Quarter Window Glass

Rear Door Glass Sub–assy

Rear Door Quarter
Window Weatherstrip

Rear Door Window Regulator Sub–assy

Power Window Regulator Motor Assy

Rear Door w/ Motor Lock Assy

Rear Door Outside
Handle Cover

Rear Door Outside
Handle Assy

Rear Door Outside Handle
Frame Sub–assy



Non–reusable part



Rear Door Lower
Frame Plate

ENGINE HOOD/DOOR

REAR DOOR

75–13

2693

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

REAR DOOR

COMPONENTS

background image

7509B–01

B50717

Centering Bolt

Standard Bolt

B56579

5.1 (0.201)



1.5 (0.059)

0



1.5

(0.059)

5.6 (0.220)



1.5 (0.059)

4.6 (0.181)



1.5 (0.059)

0



1.5 (0.059)

mm (in.)

75–14

ENGINE HOOD/DOOR

REAR DOOR

2694

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

ADJUSTMENT

HINT:



Installation is in the reverse order of the removal. But the installation is indicated only when it has a
point.



In the RH side, work in the same procedure as in the LH side.

HINT:
Since the centering bolt is used as a door hinge set bolt, the
door can not be adjusted with it on. Substitute a bolt with washer
for the centering bolt.

1.

INSPECT REAR DOOR PANEL SUB–ASSY LH

(a)

Check that the clearance is within the standard value.

2.

REMOVE FRONT DOOR SCUFF PLATE LH(See page

76–20

)

3.

REMOVE REAR DOOR SCUFF PLATE LH(See page

76–20

)

4.

REMOVE FRONT DOOR OPENING TRIM WEATHERSTRIP LH(See page

76–20

)

5.

REMOVE REAR DOOR OPENING TRIM WEATHERSTRIP LH(See page

76–20

)

6.

REMOVE CENTER PILLAR GARNISH LOWER LH(See page

76–20

)

background image

B51156

B30609

B55940

ENGINE HOOD/DOOR

REAR DOOR

75–15

2695

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

7.

ADJUST REAR DOOR PANEL SUB–ASSY LH

(a)

Adjust the door by loosening the body side hinge nuts.
Torque: 26 N

m (265 kgf

cm, 19 ft

lbf)

(b)

Adjust the door by loosening the door side hinge bolts.
Torque: 26 N

m (265 kgf

cm, 19 ft

lbf)

(c)

Adjust the striker position by slightly loosening the striker
mounting screws, and hitting the striker with a brass bar
and hammer.

(d)

Tighten the striker mounting screws again.
Torque: 23 N

m (235 kgf

cm, 17 ft

lbf)

background image

7509C–01

B56617

Clip

Clip

B56609

Clip

B56618

Clip

75–16

ENGINE HOOD/DOOR

REAR DOOR

2696

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

OVERHAUL

HINT:



Installation is in the reverse order of the removal. But the installation is indicated only when it has a
point.



In the LH side, work in the same procedure as in the RH side.

1.

REMOVE POWER WINDOW REGULATOR SWITCH
ASSY REAR

(a)

Remove the rear door armrest base cover lower.

(b)

Remove the screw.

(c)

Using a screwdriver, remove the power window regulator
switch assembly rear then disconnect the connector.

HINT:
Tape the screwdriver tip before use.

2.

REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG
LH

(a)

Using a screwdriver, remove the rear door inside handle
bezel plug.

HINT:
Tape the screwdriver tip before use.

3.

REMOVE REAR DOOR TRIM BOARD SUB–ASSY LH

(a)

Remove the 4 screws.

(b)

Using a screwdriver, remove the clip.

(c)

Using a screwdriver, remove the rear door trim board.

HINT:
Tape the screwdriver tip before use.
(d)

Remove the inside handle then disconnect the 2 cables
from the rear door lock assembly.

4.

REMOVE REAR DOOR LOWER FRAME PLATE SUB–ASSY LH

(a)

Remove the 3 screws and rear door lower frame plate.

5.

REMOVE REAR DOOR SERVICE HOLE COVER LH

(a)

Disconnect each connector and remove the rear door service hole cover.

NOTICE:
Remove the remaining tape on the body side.
6.

REMOVE REAR DOOR GLASS WEATHERSTRIP INNER LH

7.

REMOVE REAR DOOR GLASS RUN LH

background image

ENGINE HOOD/DOOR

REAR DOOR

75–17

2697

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

8.

REMOVE REAR DOOR WEATHERSTRIP LH

(a)

Using a screwdriver, remove the door weatherstrip.

HINT:
Tape the screwdriver tip before use.
9.

REMOVE REAR DOOR BELT MOULDING ASSY LH(See page

76–10

)

10.

REMOVE REAR DOOR WINDOW FRAME SUB–ASSY REAR LOWER LH

(a)

Remove the screws.

(b)

Remove the 2 bolts and rear door window frame rear lower.

11.

REMOVE REAR DOOR QUARTER WINDOW GLASS LH

(a)

Remove the rear door quarter window glass.

12.

REMOVE REAR DOOR GLASS SUB–ASSY LH

HINT:
Insert a shop rag inside the door panel to prevent scratching the glass.
(a)

Open the door glass.

(b)

Tilt the door glass and disconnect the roller of the regulator from the channel to remove the door glass.

NOTICE:
Do not damage the door glass.
HINT:
Pull the glass upward to remove it.
13.

REMOVE REAR DOOR WINDOW REGULATOR SUB–ASSY LH

(a)

Disconnect the connector.

(b)

Loosen the temporarily installed bolt.

NOTICE:
When the temporarily installed bolt is removed, the rear door window regulator might drop and be
deformed.
(c)

Remove the 3 bolts and rear door window regulator.

14.

REMOVE POWER WINDOW REGULATOR MOTOR ASSY LH

(a)

Using a torx wrench (T25), remove the 3 screws and the motor assembly.

15.

REMOVE REAR DOOR W/MOTOR LOCK ASSY LH

(a)

Disconnect the connector.

(b)

Using a torx wrench (T30), remove the 3 screws and the rear door with motor lock assembly.

16.

REMOVE REAR DOOR OUTSIDE HANDLE COVER RH

(a)

Using a torx wrench (T30), loosen the screw and remove the rear door outside handle cover.

background image

B57652

B56613

75–18

ENGINE HOOD/DOOR

REAR DOOR

2698

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

17.

REMOVE REAR DOOR OUTSIDE HANDLE ASSY LH

(a)

Pull and hold the release plate of the outside handle
frame, as shown in the illustration.

(b)

Pushing the outside handle in the arrow mark direction in
the illustration, remove the rear door outside handle.

NOTICE:
If the release plate is not pulled and held when removing
the outside handle assembly, then the release pate will in-
terfere with the outside handle and it will damage the re-
lease plate.

18.

REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB–ASSY LH

(a)

Using a torx wrench (T30), loosen the screw and remove the rear door outside handle frame.

19.

INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB–ASSY LH

(a)

Using a torx wrench (T30), install the rear door outside handle frame with the screw.

20.

INSTALL REAR DOOR OUTSIDE HANDLE COVER RH

(a)

Using a torx wrench (T30), install the rear door outside handle cover with the screw.

21.

INSTALL REAR DOOR W/MOTOR LOCK ASSY LH

(a)

Install a new door lock wire harness packing.

NOTICE:



If reusing the removed lock with rear door motor, the packing in the connecting part should be
replaced with a new one.



Be careful that grease and dirt will not stick to the packing surface in the connecting part.



Reusing the removed packing or using a damaged packing will cause water to penetrate
through the connecting part, and it will result in a malfunction of the door lock.

(b)

Engage the lock assembly with rear door motor with the release plate of the outside handle, and then
set it to the door panel.

NOTICE:
Make sure that the release plate of the outside handle frame is securely engaged with the lock assem-
bly.
(c)

Using a torx wrench (T30), install the rear door lock assembly with the 3 screws and bolt.

22.

INSTALL POWER WINDOW REGULATOR MOTOR ASSY LH

(a)

Using a torx wrench (T25), install the power window regulator motor with the 3 screws.

23.

INSTALL REAR DOOR WINDOW REGULATOR SUB–ASSY LH

(a)

Install the temporarily installed bolt securely.

(b)

Install the temporarily installed bolt to the window regulator to the rear door panel, and install the rear
door window regulator temporarily.

(c)

Tighten the 3 bolts and the temporarily installed bolt.

(d)

Disconnect the connector.

background image

B56619

Tape

ENGINE HOOD/DOOR

REAR DOOR

75–19

2699

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

24.

INSTALL REAR DOOR SERVICE HOLE COVER LH

(a)

Install a new service hole cover to the door panel.

HINT:



When installing the service hole cover, pull out the links
and connectors through the service hole cover.



There should be no wrinkles or folds on the service hole
cover after attaching it.



After attaching the service hole cover, sealing condition
should be confirmed.

background image

7509D–01

B56606

mm (in.)

8 (0.31)



1.5 (0.059)

5 (0.20)



1.5 (0.059)

4 (0.16)



1.5 (0.059)

0



1.5 (0.059)

B30599

75–20

ENGINE HOOD/DOOR

LUGGAGE COMPARTMENT DOOR

2700

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

LUGGAGE COMPARTMENT DOOR

ADJUSTMENT

1.

INSPECT LUGGAGE COMPARTMENT DOOR PANEL SUB–ASSY

(a)

Check that the clearance is within the standard value.

2.

REMOVE LUGGAGE COMPARTMENT DOOR COVER(See page

76–6

)

3.

REMOVE LUGGAGE COMPARTMENT FLOOR MAT(See page

76–5

)

4.

REMOVE SPARE WHEEL COVER ASSY(See page

76–5

)

5.

REMOVE LUGGAGE COMPARTMENT SIDE COVER SUB–ASSY RH(See page

76–5

)

6.

REMOVE LUGGAGE COMPARTMENT TRIM HOOK NO.1(See page

76–5

)

7.

REMOVE REAR FLOOR FINISH PLATE(See page

76–5

)

8.

ADJUST LUGGAGE COMPARTMENT DOOR PANEL
SUB–ASSY

(a)

For forward/rearward and right/left adjustments, loosen
the bolts.

(b)

For a vertical adjustment of the door front end, increase
or decrease the number of the washers between the
hinge and door.

background image

B50796

ENGINE HOOD/DOOR

LUGGAGE COMPARTMENT DOOR

75–21

2701

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

(c)

Using a hammer and a brass bar, tap the striker to adjust
it.

background image

7509E–01

B55944

B55945

B56621

Installation Hole

Installation Hole
(For Adjustment)

75–22

ENGINE HOOD/DOOR

LUGGAGE DOOR HINGE TORSION BAR

2702

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

LUGGAGE DOOR HINGE TORSION BAR

REPLACEMENT

NOTICE:
Hold the door when opening / closing it in order to prevent the door from closing without any resis-
tance after removing the torsion bar.
1.

REMOVE LUGGAGE COMPARTMENT FLOOR MAT

2.

REMOVE SPARE WHEEL COVER ASSY

3.

REMOVE REAR FLOOR FINISH PLATE(See page

76–4

)

4.

REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER RH(See page

76–4

)

5.

REMOVE LUGGAGE COMPARTMENT TRIM COVER INNER LH(See page

76–4

)

6.

REMOVE LUGGAGE DOOR HINGE TORSION BAR LH

(a)

Remove the torsion bar RH from the clip placed in the center of the upper back panel.

(b)

Remove the tip of the torsion bar by hand from the roof
side inner panel.

(c)

Take out the hinge arm from the torsion bar in the rear
direction.

(d)

Pull the torsion bar to your side in order to remove the
”U”–shaped part from the hinge support.

7.

REMOVE LUGGAGE DOOR HINGE TORSION BAR RH

8.

INSTALL LUGGAGE DOOR HINGE TORSION BAR LH

(a)

Check the paint mark of the torsion bar. (When installing
a new one)

HINT:



Green paint for a vehicle without rear spoiler



Yellow paint for a vehicle with rear spoiler

(b)

Set the tip of the torsion bar in the installation hole placed
in the center part. Holes placed in the upper and lower
parts are used for adjustment.

background image

ENGINE HOOD/DOOR

LUGGAGE DOOR HINGE TORSION BAR

75–23

2703

Author:

Date:

2002 CAMRY REPAIR MANUAL 185W (RM881U)

HINT:
If the return force becomes less because the torsion bar has
been damaged, adjustment should be done in the upper hole.



If the return force is little, adjust one of the torsion bars.



If the return force is still little, adjust both of the torsion
bars.

9.

INSTALL LUGGAGE DOOR HINGE TORSION BAR RH

(a)

Check the paint mark of the torsion bar. (When installing
a new one)

HINT:



White paint for a vehicle without rear spoiler



Red paint for a vehicle with rear spoiler


Wyszukiwarka

Podobne podstrony:
75 Engine Hood and Door
75 Engine Hood and Doors
75 Engine Hood and Doors
75 Engine Hood and Doors
ENGINE HOOD & DOOR
Popular Mechanics Fixing Hood And Trunk Latches
metcalf eddy wastewater engineering treatment and reuse
Metabolic Engineering T Scheper and Jens Nielsen
American Woodworker Drawer And Door Pulls (2)
73 Theft Deterrent and Door Lock
73 Anti Theft and Door Locks
Popular Mechanics Fixing Hood And Trunk Latches
73 Theft Deterrent and Door Lock
Electronic engine management and calibration
Chan S Park Engineering Economics and Project Management

więcej podobnych podstron