4 biegowa skrzynia biegów z Audi A4 (01M)

background image

13.11.2013

4-Speed Automatic Transmission (01M) - Ross-Tech Wiki

wiki.ross-tech.com/wiki/index.php/4-Speed_Automatic_Transmission_(01M)

1/2

4-Speed Automatic Transmission (01M)

Information
The 01M and 01P transmissions are built on the same version of the 4-speed automatic transmission manufactured by VW.

General Information about this Transmission can be found in the

Wikipedia entry

. Additional information can be found in

the

Official Factory Repair Information

and sources such as

Bentley Publisher's SSP (Self-Study Program)

.

Contents

[

hide

]

1 Coding
2 Basic Setting

2.1 Special Notes

3 General Notes

Coding

000?x: DSP Mode (Dynamic Shift Points)

0 = DSP active
1 = DSP inactive

000x?: Transmission Mode

0 = Factory Mode (Adaptive Transmission Mode)
1 = Force Economy Mode (lower Shift Points)
2 = Force Sport Mode (higher Shift Points)

Common Settings:

00000 = Factory Mode
00011 = Economy/Touring Mode
00012 = Sport Mode

Basic Setting

Prerequisites:

No fault codes in the Auto Trans.

Throttle Body Alignment (TBA)

performed successfully when applicable

Ignition on, engine off.
Do not touch the accelerator pedal.

[Select]
[02 - Auto Trans]
[Basic Settings - 04]
Set Group to "000"
[Go!]
Press accelerator pedal all the way to the floor and hold for 3 to 5 seconds.
[Done, Go Back]
Release the accelerator pedal.

Special Notes

It is normal for there to be no explicit instructions or changes on the screen when you do the above procedure. The
transmission controller does not provide any feedback that it has been successfully performed. Checking the binary switching

background image

13.11.2013

4-Speed Automatic Transmission (01M) - Ross-Tech Wiki

wiki.ross-tech.com/wiki/index.php/4-Speed_Automatic_Transmission_(01M)

2/2

in measuring block group 001 field 4 should confirm a change when field 3 is between 95 - 100% pedal position.
If the pedal did not travel to the floor due to an obstructions such as too many floor mats the procedure may not be successful.
If faults are stored in the Engine or Transmission for throttle related problems, the procedure will not be successful.
When the 01M transmission is installed in a vehicle using the Drive-by-Wire (DBW) throttle system, the ECM (Engine Control
Module) may support a Kick-Down Basic Settings as described here:

Automatic Transmission Basic Settings

.

General Notes

The 01M transmission has 3 speed sensors which are found in the repair manual however TSB 01-99-02 clearly describes
the location and function of the sensors (G38/G68/G22).
Vehicles with (G38/G68) specific speed sensor faults may have applicable TSBs for overlay wiring harnesses.

Jetta and Golf (9M/1J) platforms would refer to TSB 01-07-09 for G68 faults and TSB 01-06-23 for G38 faults.
New Beetle (1C) platform would refer to TSB 01-07-17 for G68 faults and TSB 01-07-16 for G38 faults

The 01M transmission has a plastic speedometer drive gear inside the transmission which operates the driven gear
connected to the G22 VSS sensor. When the transmission has internal failure of the drive gear the common concerns include
inoperative cruise control and/or speedometer.


Wyszukiwarka

Podobne podstrony:
AUDI A4 8E 2005pl
audi A4 6 stala praca wentylatora chlodnicy
Audi A4 nieszczelny parownik
[Audi A4 8E ] Zestaw naprawczy do luzujacej sie rolety w Avancie B6 i B7
kodowanie sterownikow Audi A4, auta, Diagnostyka dokumety, procedury diagnostyczne
[Audi A4 B5] Wymiana termos
audi a4 awaria reflektora ksenonowego
Audi A4 S4, 1995 2001
[Audi A4 B6] problem z silniczkiem sterującym klapy temperatur
Audi A4 ubytek plynu chlodzacego
34 SC DS300 R AUDI A4 A 98 00
[Audi A4 B6 B7] montaż klimatyzowanego schowka 100pln i 15min pracy plug@play
Instrukcja obslugi Audi A4 up by dunaj2
141 SC DS400 C AUDI A4 A 02 XX
Instrukcja Obslugi Audi A4 S4 Cabriolet en
Audi A4 S4 Cabriolet
audi A4 przewody
[Audi A4 8E] Wymiana ramienia wycieraczki tylniej w Avancie na aero z Audi Q5
[Audi A4 B6] Kasowanie SERVICE

więcej podobnych podstron