Side By Side
The Pocket Guide
Display LED Buzzer Fault
to Fault Codes
D Fdg ON ON Damper stuck or
By Technicians, for Technicians
doesn t connect.
C Fdg ON ON Fridge sensor failure.
C Fzr ON ON Freezer sensor failure.
CF Fzr ON ON Communication failure
REFRIGERATION
between main board
COOKING
and user interface.
"--" Fzr ON ON Temp in freezer WASHING
higher than  11
DISHWASHING
(temp safety limit)
"-7" or other values on Fzr AND
ON ON Black out over tempera
SIDE BY SIDES
ture alarm engaged.
Ovens
Fault Defect Intervention
F01 Open or short Replace temp Probe
circuit of temp probe.
F02 Overheating of Replace Capricorn
oven.
F03 Capricorn not Replace Capricorn
properly configured.
Whirlpool Uk Ltd
F04 WISP protocol Replace Capricorn or
209 Purley Way
not working. Scale.
Croydon
CR9 4RY
Induction Hobs
Code Fault
Tel: [phone]
Fax: [phone]
F Sensor
F3 Config error
F12 Communication error
Compiled and Edited by:
F22 Key sensitivity error
Touch Control Hob Peter Martins and Adam Bigden
Code Fault
Whirlpool Technical Team
F3 Config error
Email: [e-mail]
F12 WISP communication error
F22 Key sensitivity error
Every home, everywhere& & ...with Pride,
[e-mail]
Passion, Performance!
Dishwasher Steam Chef Smart Gas
I
Code Fault Code Fault Code Fault
F01 on/off valve stuck open.
F0 Sensor Failure F0 Incorrect value of cavity sensor.
F02 Communication problem.
F1 NTC Failure F1 Incorrect value of cavity sensor.
F03 Control board problem.
F2 Water Leakage F2 Incorrect value of Food Probe.
F04 User interface problem.
F3 Heating system failure F3 Incorrect value of climate sensor.
F05 Continuous E2 prom reset.
F4 Draining failure F4 Incorrect current value from flap motor.
F11 Burner 1 open circuit on thermocouple.
F5 Rotor blocked F5 Unable to backup EEPROM.
F21 Burner 2 open circuit on thermocouple.
F6 Water tap closed F7 No, or slow increase of water
F31 Burner 3 open circuit on thermocouple.
temperature.
F7 Flow meter failure
F41 Burner 4 open circuit on thermocouple.
F8 Water level failure F8 Level sensor detects water after
F9 Continuous water inlet draining.
F12 Burner 1 PWM valve stuck open.
FA Optical water indicator F9 No or slow increase of climate
F22 Burner 2 PWM valve stuck open.
temperature.
FB Motorised diverter valve
F32 Burner 3 PWM valve stuck open.
FC Water hardness sensor failure No Indication Oven does not heat.
F42 Burner 4 PWM valve stuck open.
WASHING M/C Microwave Ovens
Washer/Dryers
Code Fault Code Fault
Code Fault
Open Check the closure of the porthole and
FH No water inlet ERR0 Convection temperature fault, not
relating indicator in case it is open.
connected or short circuit
FA Aquastop failure
E01 Display shows the safety device for
FP Drain failure ERR1 Short circuit in the MW relay
water loss has tripped.
F5 NTC failure ERR3 Key error when one of the buttons is
E02 Overflow engaged (only out of a
pressed for more than 1 minute
F6 Tachometer failure (no motor
washing program)
movement detected) ERR6 Weight sensor calibration has not
E04 Water temperature probe in short circuit
been performed
F7 Triac short circuit detection
or interrupted.
F8 Heating element, open circuit ERR7 Humidity sensor is defective or has not
E05 As water is being loaded, if the pressure
F9 Overflow failure been connected
switch does not reach the full level
F10 Motor control unit (thermal) ERR8 Impossible to write to E2 Prom
within the first 6 , problem displayed.
F11 Communication failure ERR9 Options have not been set
E06 If during water drain, the empty level is
F12 Heating element short circuit ERR A No wheel detected on weight sensor
not reached in 10 , problem displayed.
F13 Dispenser circuit error ERR B No pulses from the weight sensor or
E10 Motor over-current.
<4267Hz
F14 EEPROM Failure
E11 Problem of motor control triac (short
F15 Motor control unit error ERR C Fuzzy temperature sensor fault not 19-
circuit or interrupted).
41C
F16 Control failure (control unit)
E12 Indication for tachyometry malfunction.
F18 Control failure (control unit) ERR D NTC overheat protection on the
E13 Malfunctioning door block PTC.
F20 Control failure (control unit) magnetron is faulty (not connected or
E14 Dryer temperature probe in short circuit
short circuit)
F21 Control failure (user board)
or interrupted.
F22 Control failure (user board)
E- Communication problem between inter
FDL Door lock error
face board and mother board.
FDU Door unlock error
E- Board hardware problem.
I