2009 ACCESSORIES & EQUIPMENT

Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town & Country

DIAGNOSTIC CODE INDEX

DIAGNOSTIC CODE INDEX

DIAGNOSIS AND TESTING

B1539-SATELLITE VIDEO ANTENNA PERFORMANCE (NOT CONNECTED)

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

With the ignition on and the Radio in Satellite Video Mode.



Set Condition:

If the Satellite Video Module does not detect an antenna connection, this code will set.

Diagnostic Test

DTC

Description

B1539

SATELLITE VIDEO ANTENNA PERFORMANCE (NOT CONNECTED)

B210D

BATTERY VOLTAGE LOW

B210E

BATTERY VOLTAGE HIGH

B2287

SATELLITE VIDEO RECEIVER INTERNAL

U0010

CAN INTERIOR BUS

U0011

CAN INTERIOR BUS OFF PERFORMANCE

U0141

LOST COMMUNICATION WITH IPM (FCM/TIPM)

U0184

LOST COMMUNICATION WITH RADIO

U0196

LOST COMMUNICATION WITH VEHICLE ENTERTAINMENT CONTROL

MODULE - FIRST ROW

Possible Causes

BAD SATELLITE VIDEO ANTENNA CONNECTION
OPEN SATELLITE VIDEO ANTENNA CABLE
OPEN SATELLITE VIDEO ANTENNA
SATELLITE VIDEO MODULE

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 1

© 2006 Mitchell Repair Information Company, LLC.

steve

Monday, May 23, 2011 2:01:55 PM

Page 1

© 2006 Mitchell Repair Information Company, LLC.

1. CHECK CONNECTOR

1. Turn the ignition off.

2. Disconnect the Satellite Video Antenna Cable connector at the Satellite Video Antenna.

3. Inspect the Satellite Video Antenna connection.

Was the Antenna connection clean and secure?

Yes



Go to 2

No



Repair the Antenna connection as needed.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

2. SATELLITE VIDEO MODULE

1. Turn the ignition on.

2. With the scan tool, record, then erase the Satellite Video Module DTCs.

3. Turn the ignition off.

4. Connect a known good Satellite Video Antenna and Cable to the Satellite Video Module.

5. Turn the ignition and the Radio on.

6. Put the Radio in Satellite Video Mode.

7. With the scan tool, read the active Satellite Video Module DTCs.

Does the scan tool display: B1539 Satellite Video Antenna Performance (Not Connected) as
Active?

Yes



Replace the Satellite Video Module in accordance with the service information.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No



Go to 3

NOTE:

To continue with this test, you must secure a Known Good Satellite Video
Antenna and Cable.

NOTE:

Move vehicle outside approximately 9.14 m (30 ft.) from any structure.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 2

© 2006 Mitchell Repair Information Company, LLC.

3. SATELLITE VIDEO ANTENNA

1. With the scan tool, record, then erase the Satellite Video Module DTCs.

2. Turn the ignition off.

3. Disconnect the Satellite Video Antenna Cable connector at the Satellite Video Antenna.

4. Reconnect the original Satellite Video Antenna to the known good Satellite Video Antenna Cable.

5. Turn the ignition on.

6. Put the Radio in Satellite Video Mode.

7. With the scan tool, read the active Satellite Video Module DTCs.

Does the scan tool display: B1539 Satellite Video Antenna Performance (Not Connected) as
Active?

Yes



Replace the Satellite Video Antenna in accordance with the service information.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No



Go to 4

4. SATELLITE VIDEO ANTENNA CABLE

1. With the scan tool, record, then erase the Satellite Video Module DTCs.

2. Turn the ignition off.

3. Disconnect the Satellite Video Antenna Cable connectors at the Satellite Video Antenna and the

Satellite Video Module.

4. Reconnect the original Satellite Video Antenna Cable to the Satellite Video Antenna and the

Satellite Video Module.

5. Turn the ignition on.

6. Put the Radio in Satellite Video Mode.

7. With the scan tool, read the active Satellite Video Module DTCs.

Does the scan tool display: B1539 Satellite Video Antenna Performance (Not Connected) as
Active?

Yes



Replace the Satellite Video Antenna Cable in accordance with the service information.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 3

© 2006 Mitchell Repair Information Company, LLC.



The condition that caused this symptom is currently not present. Check for an intermittent
condition by inspecting the related wiring harness for chafed, pierced, pinched, and partially
broken wires. Also, inspect the related connectors for broken, bent, pushed out, spread,
corroded, or contaminated terminals. Repair as necessary.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

B210D-BATTERY VOLTAGE LOW

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

With the ignition on.



Set Condition:

Battery voltage less than 9 volts for more than 15 seconds.

Diagnostic Test

1. CHECK FOR ANY POWERTRAIN CONTROL MODULES DTCS

1. Turn the ignition on.

Possible Causes

BATTERY
GENERATOR
POWERTRAIN CONTROL MODULE (PCM)

NOTE:

Make sure the Battery is in good condition. Using the Midtronics Battery
Tester, test the Battery before continuing.

NOTE:

Inspect the vehicle for after market accessories that may exceed the
Generator System output.

NOTE:

Make sure the generator drive belt is in good operating condition.

NOTE:

Inspect the fuses in the IPM. If an open fuse is found, use the wire
diagram/schematic as a guide, inspect the wiring and connectors for
damage.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 4

© 2006 Mitchell Repair Information Company, LLC.

2. With the scan tool, read active PCM DTCs.

Does the scan tool display any active battery or charging DTCs?

Yes



Refer to DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard
Procedure and perform the appropriate battery or charging system diagnostic procedure.

No



Check the above conditions that can cause a low voltage condition. Repair as necessary.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

B210E-BATTERY VOLTAGE HIGH

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

With the ignition on.



Set Condition:

Battery voltage greater than 16 volts for more than 15 seconds.

Diagnostic Test

1. CHECK FOR ANY POWERTRAIN CONTROL MODULES DTCS

Possible Causes

BATTERY
GENERATOR
POWERTRAIN CONTROL MODULE (PCM)

NOTE:

Make sure the Battery is in good condition. Using the Midtronics Battery
Tester, test the Battery before continuing.

NOTE:

Inspect the vehicle for after market accessories that may exceed the
Generator System output.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 5

© 2006 Mitchell Repair Information Company, LLC.

1. Turn the ignition on.

2. With the scan tool, read active PCM DTCs.

Does the scan tool display any active battery or charging system DTCs?

Yes



Refer to DTC-Based Diagnostics/MODULE, Powertrain Control (PCM) - Standard
Procedure and perform the appropriate battery or charging system diagnostic procedure.

No



Check the above conditions that can cause a high voltage condition. Repair as necessary.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

B2287-SATELLITE VIDEO RECEIVER INTERNAL

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

With the ignition on.



Set Condition:

The Satellite Video Module detects an internal failure.

Diagnostic Test

1. SATELLITE VIDEO MODULE

If DTC: B2287-SATELLITE VIDEO RECEIVER INTERNAL is active, view repair.

NOTE:

Make sure the generator drive belt is in good operating condition.

NOTE:

Inspect the fuses in the IPM. If an open fuse is found, use the wire
diagram/schematic as a guide, inspect the wiring and connectors for
damage.

Possible Causes

SATELLITE VIDEO MODULE

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:51 PM

Page 6

© 2006 Mitchell Repair Information Company, LLC.

Repair



Replace the Satellite Video Module in accordance with the service information.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

U0010-CAN INTERIOR BUS

Fig. 1: CAN Interior Bus Schematic
Courtesy of CHRYSLER LLC

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 7

© 2006 Mitchell Repair Information Company, LLC.

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

Continuously when the ignition is on.

Battery voltage between 10 and 16 volts.

IOD fuse installed.



Set Condition:

The Totally Integrated Power Module (TIPM) detects a short to ground on the CAN Interior Bus (125K)
(+) circuit or a short to voltage on the CAN Interior Bus (125K) (-) circuit.

Diagnostic Test

1. VERIFY DTC IS ACTIVE

1. Turn the ignition on.

2. With the scan tool, read active Satellite Video Receiver DTCs.

Possible Causes

(D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO GROUND
(D264) CAN INTERIOR BUS (125K) (-) CIRCUIT SHORTED TO VOLTAGE
ANY CAN INTERIOR BUS MODULE
TOTALLY INTEGRATED POWER MODULE

NOTE:

Make sure the IOD fuse is installed and the battery is fully charged before
proceeding.

NOTE:

This module will not be able to communicate when this fault is active and
therefore will only display this DTC as stored. To diagnose this DTC, use a
scan tool and check for DTCs in the TIPM. If DTCs are active. Refer to DTC-
Based Diagnostics/MODULE, Totally Integrated Power (TIPM) - Diagnosis
and Testing and perform the appropriate diagnostic procedure. If no DTCs
are active, but there are stored Lost Communication DTCs. Refer to Non-
DTC Diagnostics/Communication - Diagnosis and Testing and perform the
appropriate No Response diagnostic procedure. If no DTCs are set,
perform the BODY VERIFICATION TEST. Refer to DTC-Based
Diagnostics/MODULE, Totally Integrated Power (TIPM) - Standard
Procedure .

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 8

© 2006 Mitchell Repair Information Company, LLC.

Is this DTC active?

Yes



Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) -
Diagnosis and Testing and perform the diagnostic procedure for this DTC.

No



Refer to Non-DTC Diagnostics/Communication - Diagnosis and Testing and perform the
Stored Lost Communication DTCs diagnostic procedure.

U0011-CAN INTERIOR BUS OFF PERFORMANCE

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 9

© 2006 Mitchell Repair Information Company, LLC.

Fig. 2: CAN Interior Bus Off Performance Schematic
Courtesy of CHRYSLER LLC

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.

Theory of Operation

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 10

© 2006 Mitchell Repair Information Company, LLC.

The primary communication network between electronic control modules on this vehicle is the Controller Area
Network (CAN) data bus system. The Controller Area Network (CAN) data bus allows all electronic modules
connected to the bus to share information with each other. Regardless of whether a message originates from a
module on the higher speed CAN C (500K) Bus or on the lower speed CAN Interior High Speed (IHS) (125K)
Bus the message structure and layout is similar, which allows the Totally Integrated Power Module/Central
GateWay (TIPM or TIPMCGW) to process and transfer messages between the CAN buses. The TIPM also
stores Diagnostic Trouble Codes (DTCs) for certain bus network faults.

All modules transmit and receive messages over one of these buses. Data exchange between the modules is
achieved by serial transmission of encoded data messages (a form of transmission in which data bits are sent
sequentially, one at a time, over a single line). Each module can both send and receive serial data
simultaneously. Each data bit of a CAN Bus message is carried over the bus as a voltage differential between
the two bus circuits which, when strung together, form a message. Each module uses arbitration to sort the
message priority if two competing messages are attempting to be broadcast at the same time. Corruption of a
single bit within a message will corrupt the entire message. Each message contains a Cyclic Redundancy Check
(CRC) which specifies the message size exactly. If the message detected conflicts with the CRC the ECU
receiving it will determine the message to be an error and consider that communication has not been possible.
Diagnosis of this condition using a lab scope may reveal activity that appears to be Bus data messages even if
no actual communication is possible. Communication problems that affect the whole bus, as a result of opens
and terminal push outs are more likely to occur on data busses that operate at a high speed than a data bus that
operates at a lower speed.

When an open circuit or terminal push out occurs one or more modules can become isolated from the remainder
of the bus. The isolated module will attempt to communicate. Since each module contains it own termination a
module that is isolated may receive its own messages correctly but will not be able to receive messages or
determine arbitration from other modules. Each time the isolated module attempts to communicate it alters the
bus voltage on the intact bus circuit. Without functioning arbitration the isolated module alters the bus voltage
while other bus messages are being sent thereby corrupting the messages on the remainder of the bus.

The CAN bus modules are connected in parallel to the two-wire bus using a twisted pair, where the wires are
wrapped around each other to provide shielding from unwanted electromagnetic induction, thus preventing
interference with the relatively low voltage signals being carried through them. While the CAN bus is operating
(active), one of the bus wires will carry a higher voltage and is referred to as the CAN High or CAN bus (+)
wire, while the other bus wire will carry a lower voltage and is referred to as the CAN Low or CAN bus (-)
wire.



When Monitored:

With the ignition on.



Set Condition:

A module detects the CAN Interior Bus circuits shorted to ground, shorted together or shorted to voltage.

Possible Causes

(D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO GROUND
(D264) CAN INTERIOR BUS (125K) (-) CIRCUIT SHORTED TO GROUND

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 11

© 2006 Mitchell Repair Information Company, LLC.

Diagnostic Test

1. TEST FOR INTERMITTENT CONDITION

1. Turn the ignition on.

2. Using the scan tool, record and erase DTCs.

3. Cycle the ignition from on to off three times.

4. Turn the ignition on.

5. Using the scan tool, read active DTCs.

Does the scan tool display this DTC as active?

Yes



Go to 2

No



The conditions that caused this code to set are not present at this time. Using the wiring
diagram/schematic as a guide, inspect the wiring and connectors.

2. ANY CAN INTERIOR BUS (125K) MODULE-INTERNAL SHORT

1. While monitoring the scan tool, disconnect each CAN Interior Bus (125K) module (except the

TIPM itself), one at a time.

2. Check for this DTC to become stored after disconnecting each CAN Interior Bus (125K) module

the vehicle is equipped with.

With all the CAN Interior Bus modules disconnected does the scan tool display this DTC as active?

(D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO (D264) CAN INTERIOR BUS
(125K) (-) CIRCUIT
(D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO VOLTAGE
(D264) CAN INTERIOR BUS (125K) (-) CIRCUIT SHORTED TO VOLTAGE
ANY CAN INTERIOR BUS MODULE
TOTALLY INTEGRATED POWER MODULE

NOTE:

When performing this step, turn the ignition off (wait one minute) before
disconnecting any module. When the module is disconnected turn the
ignition on.

NOTE:

This step is to determine if the fault is internal within a module.

NOTE:

If the DTC becomes stored when a particular module is disconnected,
that module is causing the DTC to set.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 12

© 2006 Mitchell Repair Information Company, LLC.

Yes



Go to 3

No



Replace the module that when disconnected caused this DTC to become stored in accordance
with the service information.



Perform the appropriate verification test.

3. (D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO GROUND

Fig. 3: Checking CAN Interior Bus (+) Circuit For Short To Ground
Courtesy of CHRYSLER LLC

1. Turn the ignition off.

2. Disconnect the TIPM C7 Harness connector.

3. Measure the resistance between ground and the (D265) CAN Interior Bus (125K) (+) circuit at the

TIPM C7 harness connector.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 13

© 2006 Mitchell Repair Information Company, LLC.

Is the resistance below 10,000.0 ohms?

Yes



Repair the (D265) CAN Interior Bus (125K)(+) circuit for a short to ground.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No



Go to 4

4. (D264) CAN INTERIOR BUS (125K) (-) CIRCUIT SHORTED TO GROUND

Fig. 4: Checking CAN Interior Bus (-) Circuit For Short To Ground

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 14

© 2006 Mitchell Repair Information Company, LLC.

Courtesy of CHRYSLER LLC

1. Measure the resistance between ground and the (D264) CAN Interior Bus (125K) (-) circuit at the

TIPM C7 harness connector.

Is the resistance below 10,000.0 ohms?

Yes



Repair the (D264) CAN Interior Bus (125K) (-) circuit for a short to ground.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No



Go to 5

5. (D265) CAN INTERIOR BUS (125K)(+) CIRCUIT SHORTED TO THE (D254) CAN INTERIOR

BUS (-) CIRCUIT

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 15

© 2006 Mitchell Repair Information Company, LLC.

Fig. 5: Checking CAN Interior Bus (+) Circuit For Short To CAN Interior Bus (-) Circuit
Courtesy of CHRYSLER LLC

1. Measure the resistance between the (D265) CAN Interior Bus (125K)(+) circuit and the (D254)

CAN Interior Bus (125) (-) circuit at the TIPM C7 harness connector.

Is the resistance below 10,000.0 ohms?

Yes



Repair the (D265) CAN Interior Bus (125K)(+) circuit for a short to the (D264) CAN Interior
Bus (125K) (-) circuit.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 16

© 2006 Mitchell Repair Information Company, LLC.

No



Go to 6

6. (D264) CAN INTERIOR BUS (125K) (-) CIRCUIT SHORTED TO VOLTAGE

Fig. 6: Checking CAN Interior Bus (-) Circuit For Short To Voltage
Courtesy of CHRYSLER LLC

1. Turn the ignition on.

2. Measure the voltage between ground and the (D264) CAN Interior Bus (125K) (-) circuit at the

TIPM C7 harness connector.

Is the voltage above 0.02 volts?

Yes



Repair the (D264) CAN Interior Bus (125K) (-) circuit for a short to voltage.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 17

© 2006 Mitchell Repair Information Company, LLC.

Totally Integrated Power (TIPM) - Standard Procedure .

No



Go to 7

7. (D265) CAN INTERIOR BUS (125K) (+) CIRCUIT SHORTED TO VOLTAGE

Fig. 7: Checking CAN Interior Bus (+) Circuit For Short To Voltage
Courtesy of CHRYSLER LLC

1. Measure the voltage between ground and the (D265) CAN Interior Bus (125K) (+) circuit at the

TIPM C7 harness connector.

Is the voltage above 0.02 volts?

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 18

© 2006 Mitchell Repair Information Company, LLC.

Yes



Repair the (D264) CAN Interior Bus (125K) (+) circuit for a short to voltage.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

No



Inspect the wiring and all module connectors for damage or shorted pins. If OK, replace and
program the Totally Integrated Power Module in accordance with service information.



Perform the BODY VERIFICATION TEST. Refer to DTC-Based Diagnostics/MODULE,
Totally Integrated Power (TIPM) - Standard Procedure .

U0141-LOST COMMUNICATION WITH IPM (FCM/TIPM)

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 19

© 2006 Mitchell Repair Information Company, LLC.

Fig. 8: IPM (FCM/TIPM) Schematic
Courtesy of CHRYSLER LLC

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 20

© 2006 Mitchell Repair Information Company, LLC.

Continuously when the ignition is on.

Battery voltage between 10 and 16 volts.

Ignition Off Draw (IOD) fuse installed.

Totally Integrated Power Module (TIPM) is configured correctly.



Set Condition:

Bus messages not received from the TIPM for approximately two to five seconds.

Diagnostic Test

1. VERIFY DIAGNOSTIC TROUBLE CODE (DTC) IS ACTIVE

1. With the scan tool, read active Hands Free Module DTCs.

Is this DTC active?

Yes



Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) -
Diagnosis and Testing and perform the U0141-Lost Communication with IPM
(FCM/TIPM) diagnostic procedure.

No



Refer to Non-DTC Diagnostics/Communication - Diagnosis and Testing and perform the
Stored Lost Communication DTCs diagnostic procedure.

U0184-LOST COMMUNICATION WITH RADIO

Possible Causes

BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
TIPM NOT CONFIGURED CORRECTLY
TIPM
TIPM POWER AND GROUND
MODULE THAT SET THIS DTC

NOTE:

Make sure the IOD fuse is installed and battery voltage is between 10 and
16 volts before proceeding.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 21

© 2006 Mitchell Repair Information Company, LLC.

Fig. 9: Radio Schematic
Courtesy of CHRYSLER LLC

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 22

© 2006 Mitchell Repair Information Company, LLC.

Continuously when the ignition is on.

Battery voltage between 10 and 16 volts.

Ignition Off Draw (IOD) fuse installed.

Totally Integrated Power Module (TIPM) is configured correctly.



Set Condition:

Bus messages not received from the Radio for approximately two to five seconds.

Diagnostic Test

1. VERIFY DIAGNOSTIC TROUBLE CODE (DTC) IS ACTIVE

1. With the scan tool, read active Hands Free Module (HFM) DTCs.

Is this DTC active?

Yes



Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) -
Diagnosis and Testing and perform the U0184-Lost Communication with Radio diagnostic
procedure.

No



Refer to Non-DTC Diagnostics/Communication - Diagnosis and Testing and perform the
Stored Lost Communication DTCs diagnostic procedure.

U0196-LOST COMMUNICATION WITH VEHICLE ENTERTAINMENT CONTROL MODULE -
FIRST ROW

Possible Causes

BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
TIPM NOT CONFIGURED CORRECTLY
RADIO
RADIO POWER AND GROUND
MODULE THAT SET THIS DTC

NOTE:

Make sure the IOD fuse is installed and battery voltage is between 10 and
16 volts before proceeding.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 23

© 2006 Mitchell Repair Information Company, LLC.

Fig. 10: Vehicle Entertainment Control Module - First Row Schematic
Courtesy of CHRYSLER LLC

For complete wiring diagrams refer to:



SYSTEM WIRING DIAGRAMS for Town & Country.



SYSTEM WIRING DIAGRAMS for Grand Caravan.



When Monitored:

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 24

© 2006 Mitchell Repair Information Company, LLC.

Continuously when the ignition is on.

Battery voltage between 10 and 16 volts.

Ignition Off Draw (IOD) fuse installed.

Totally Integrated Power Module (TIPM) is configured correctly.



Set Condition:

Bus messages not received from the Vehicle Entertainment Control Module - First Row for
approximately two to five seconds.

Diagnostic Test

1. VERIFY DIAGNOSTIC TROUBLE CODE (DTC) IS ACTIVE

1. With the scan tool, read active Hands Free Module (HFM) DTCs.

Is this DTC active?

Yes



Refer to DTC-Based Diagnostics/MODULE, Totally Integrated Power (TIPM) -
Diagnosis and Testing and perform the U0196-Lost Communication with Vehicle
Entertainment Control Module - First Row diagnostic procedure.

No



Refer to Non-DTC Diagnostics/Communication - Diagnosis and Testing and perform the
Stored Lost Communication DTCs diagnostic procedure.

Possible Causes

BUS CIRCUITS OPEN OR SHORTED
DTCS RELATED TO BATTERY VOLTAGE, IGNITION, OR VIN MESSAGES
TIPM NOT CONFIGURED CORRECTLY
VEHICLE ENTERTAINMENT CONTROL MODULE - FIRST ROW
VEHICLE ENTERTAINMENT CONTROL MODULE - FIRST ROW POWER AND GROUND
MODULE THAT SET THIS DTC

NOTE:

Make sure the IOD fuse is installed and battery voltage is between 10 and
16 volts before proceeding.

2009 Dodge Grand Caravan SE

2009 ACCESSORIES & EQUIPMENT Video Satellite (SDARV) - Electrical Diagnostics - Grand Caravan, Town &

Country

steve

Monday, May 23, 2011 2:01:52 PM

Page 25

© 2006 Mitchell Repair Information Company, LLC.