{Change Comments ***********************************************************}

{7/24/90, Added InitProg globally to posts with this remark, DWB}
{11/20/90, Updated: Fanuc 5T [+Ä] L027.54 to .71 format, JR}

{3/29/91
Modified: Fanuc 5T [+Ä] L027.71
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 10T MS [-] L001.80 Format.
All normal Fanuc Canned Cycles except for Drilling are supported.
DWB}

{08/05/91
Updated: Fanuc 5T [+Ä] L027.80
Updated to Version 4.0 per Fanuc 6M M001.82 Format.
Kim Michelman}

{8/26/95, Updated Fanuc 5T [+Ä] L027.82 to .85 format per Fanuc 10T MS [-] L001.85.01, JR}

{7/22/98
Initial: Fanuc 5T [+Ä] L027.85
Created: Fanuc 5T P&W Star Lxxx.85
ForUser: Modern Machine
Control: General Numeric/Fanuc System 5T
Machine: Pratt & Whitney Star Turning Center
Develop: ComPost2 1.1b3, Virtual Gibbs 4.24
Comment: New processor per marked up readout and conversation with Jim Nye
Modified Spindle Speeds.
Constant Surface Speed is not supported and should not be selected in the Virtual file!
Added Tables for Gear and Speed Codes for High Pulley Speed Range
Table #1 is for Gear Code M25 or M24.
Table #2 is for Speed Codes S1 thru S4.
RPM Chart:
S1 S2 S3 S4
M24 178 355 713 1426
M25 247 494 989 1978
Added XsAreRadii command to output radius values.
Only has Simple Canned Cycles, deleted others from Prog and Form.
Deleted Retag and changed sequencing.
Updated per Fanuc 10T MS [-] L001.85.01.02
Jim Radcliffe}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###^###0'
#3 = '#######0'
#4 = '###^##0'
#5 = '#'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(MUL#,2) { Non-Canned Threading AutoFinish }
FORMAT(InFeedAngle#,2)
FORMAT(FirstMoveEPX#,2)
FORMAT(FirstMoveEPZ#,2)
FORMAT(Program#,3) {.72}
FORMAT(Operation#,3) {.72}
FORMAT(Tool#,3) {.72}
FORMAT(Dwell#,4) {.72}
FORMAT(RapidF#,5)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolSize$ ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags from last Op, .70}
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

GearCode:
TABLE(1,SpeedRPM#,1)
RETURN

SpeedCode:
TABLE(2,SpeedRPM#,1)
RETURN

StockOnNoCan:
IF NOT CannedCycle?
StockOn {need stock for SP positioning, if not a canned cycle}
END
RETURN

FeedNoCan:
IF NOT CannedCycle?
FeedC
END
RETURN

FeedRateNoCan:
IF NOT CannedCycle?
FeedRateC
END
RETURN

ApproachSP:
IF ApproachFace?
SeqC StockOnNoCan XSPC EOL
SeqC StockOff ZOpCPC EOL
StockOnNoCan
IF NotEqual? CycleStartZ# ZOpCP#
SeqC FeedNoCan ZSPC FeedRateNoCan EOL
END
ELSE { ODApproach/IDApproach }
SeqC StockOnNoCan ZSPC EOL
SeqC StockOff XOpCDC EOL
StockOnNoCan
IF NotEqual? CycleStartX# XOpCD#
SeqC FeedNoCan XSPC FeedRateNoCan EOL
END
END
RETURN

AppMove:
StockOff ThisOpEntryZCP OpToolID LatheOffset CoolOn
RETURN

Approach: { NOT FOR TAILSTOCK, .82 }
Rapid RapidF# { RapidF# Forces FeedRate }
IF ApproachOD?
SeqC ThisOpEntryXCP AppMove EOL
ELSE
IF ApproachID?
SeqC XOpCD AppMove EOL
ELSE {ApproachFace}
SeqC StockOnNoCan XSP AppMove EOL
END
END
ApproachSP
RETURN

CheckOffset:
DoEndOpPS
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
END
DoOpComments
DoPostScript
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SeqC GearCode EOL
END
SeqC
IF NotEqual? SpeedRPM# LAST SpeedRPM#
SpeedCode
END
IF NewToolOffset?
LOfstOff '00'
END
IF LAST ProgStop?
SpinOn
END
EOL
SeqC
IF NewToolOffset?
OpToolID LatheOffset
END
IF LAST ProgStop?
CoolOn
ELSE
IF NOT CoolOff? AND LAST CoolOff?
CoolOn
END
END
EOL
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXC MoveZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR ZMove? { Approach Length Feature and Multiple Pockets }
IF NOT LastFeat?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN

ToolPath:
EACHFeat
GetToolTip
IF LastFeat?
IF Drilling?
IF Tap?
SeqC SpinOff EOL
SeqC 'G04P2000' EOL
SeqC Speed InverseSpinOn EOL
ELSE
IF Dwell?
SeqC 'G04P' Dwell# EOL
END
END
END
END
IF PointFeat?
SeqC MoveSXYC EOL
ELSE
IF RapidFeat?
SeqC
IF LAST ThreadFeat?
Rapid
ELSE
RapidC
END
MoveXC MoveZC EOL
ELSE
IF LineFeat?
SeqC CkCRC FeedC MoveXC MoveZC FeedRateC EOL
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, LAST, FIRST or NEXT modifiers in this loop }
SeqC FormatArc FeedRateC EOL
NEXTQuadrant
ELSE
IF ThreadFeat?
SeqC 'G32' MoveXC MoveZC ThrdLead EOL
END
END
END
END
END
NEXTFeat
RETURN

CheckRapid:
CRCOffC
IF LAST CannedCycle?
Rapid
ELSE
IF LAST Threading?
Rapid
ELSE
RapidC
END
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
SetAbs
PosSideLathe
StandardXZArcs
XsAreRadii
SetMaxRPM('1978')
SetMaxFeed('500') {?}
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: must be all capital letters when typed in.' EOL
' ENDOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
GetLCycle
IF FirstOperation?
EOR EOL
IF UseComments?
IF ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ABSOLUTE INCHES )' EOL
END
END
RestoreScale
OpenSub
StockOff {.71.2}
SetHome
DoOpComments
DoPostScript
Plane
Seq GearCode EOL
SeqC Preset Home EOL
SeqC SpeedCode OpToolID '00' SpinOn EOL
Approach
ELSE
IF NewTool?

{Finish off last Operation}

StockOff {.62}
CheckRapid
IF LAST ApproachOD?
SeqC LAST OpExitXCPC EOL
ELSE
IF LAST ApproachID?
SeqC LAST XOpECDC EOL
END
END
SeqC LAST OpExitZCPC EOL
DoEndOpPS
SeqC NewHome LOfstOff '00' EOL
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
SeqC ProgStop EOL
END

{Start new Operation}

DoOpComments
DoPostScript
Seq GearCode EOL
SeqC Preset Home EOL
SeqC SpeedCode OpToolID '00' SpinOn EOL
Approach
ELSE
IF SameTool? {.62}

{Start new Operation}

StockOff
IF LAST StraightConnect?
CheckOffset
CheckRapid
SeqC StockOnNoCan XSPC ZSPC EOL
ELSE
CheckRapid
IF ApproachOD?
IF LAST ApproachOD?
SeqC LAST XOpECDC EOL
ELSE {around}
IF LAST ApproachID?
SeqC LAST XOpECDC EOL
END
SeqC LAST OpExitZCPC EOL
SeqC LAST OpExitXCPC EOL
END
ELSE
IF ApproachID?
IF LAST ApproachID?
SeqC LAST XOpECDC EOL
ELSE
IF LAST ApproachOD? {around}
SeqC LAST OpExitXCPC EOL
END
SeqC LAST OpExitZCPC EOL
SeqC XOpCDC EOL
END
ELSE {ApproachFace}
IF LAST ApproachFace?
SeqC LAST ZOpECPC EOL
ELSE
IF LAST ApproachOD? {around}
SeqC LAST OpExitXCPC EOL
ELSE {LAST ApproachID}
SeqC LAST XOpECDC EOL
END
SeqC LAST OpExitZCPC EOL
END
END
END
CheckOffset
ApproachSP
END
END
END
END {common point for all operations}
IF CannedCycle?
StockOff
IF Roughing?
IF RoughSimple?
StockOn
SetPass1
SeqC LCycle
IF ApproachFace?
'Z' FirstMoveEPZ# XatFinZ
ELSE
XatFinZ FinZ
END
XTapAtZ FeedRate EOL
SimpleRough
ELSE
'**Unsupported Cycle**' EOL
END
ELSE
IF Threading?
SeqC 'G92X' FirstMoveEPX# FinZ XTapAtZ ThrdLead EOL
SimpleRough
SeqC XatFinZ EOL
IF AutoFinish?
SeqC XatFinZ EOL
END
END
END
ELSE
StockOn
SetPass1
ToolPath
IF AutoFinish? { .82.1c }
StockOff
IF Turning?
IF ApproachFace?
SeqC RapidC ZOpECPC EOL
ELSE
SeqC RapidC XOpECDC EOL
END
ApproachSP
SeqC StockOff StrtPosC EOL
ToolPath
ELSE
IF Roughing? AND NOT RoughSimple?
SetPass2
SeqC RapidC XSPC ZSPC EOL
SeqC StockOff StrtPosC EOL
ToolPath
SetPass1
ELSE
IF Threading?
SeqC 'X' MUL# Num#('1') ADD# FinishXRadius# Taper# EOL
SeqC 'G32'
IF Taper?
XatFinZ
END
FinZ ThrdLead EOL
SeqC Rapid XSP EOL
SeqC ZSP EOL
END
END
END
END
END
IF Drilling? AND Tap?
SeqC SpinOff EOL
SeqC 'G04P2000' EOL
SeqC Speed SpinOn EOL
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
StockOff
CRCOffC
IF CannedCycle?
Rapid
ELSE
IF Threading?
Rapid
ELSE
RapidC
END
END
IF ApproachOD?
SeqC OpExitXCPC EOL
ELSE
IF ApproachID?
SeqC XOpECDC EOL
END
END
SeqC OpExitZCPC EOL
DoEndOpPS
SeqC CoolOff EOL
SeqC FirstHome OpToolID '00' SpinOff EOL
SeqC UnTool '00' EOL
IF ProgStop?
SeqC 'M00' EOL
END
SeqC EOP EOL
Post
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END