Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
Before starting assembly:Writing the number of each section on its back side before
Indicates where sections
cutting out the sections is highly recommended.
should be glued together.
(* This way, you can be sure which section is which even after cutting out the sections.)
http://www.canon.com/c-park/en/
( )
1 Build the base.
2
1
View of completed model
*This model was designed for Papercraft and may differ from the original in some respects.
Assembly Instructions: Six A4 sheets (No.1 to No.6)
*Build the model by carefully reading the Assembly Instructions, in the parts sheet page order.
4
6
*Hint: Trace along the folds with a ruler
and an exhausted pen (no ink) to get a sharper, easier fold.
8
Assembly Instructions
Glue
Mountain fold(dotted line)
The glue spot(colored dot)
Make a mountain fold.
shows where to apply the glue.
Valley fold(dashed and dotted line)
Glue spot(Red dot)
5
Make a valley fold.
Glue parts with the same number together.
Scissors line(solid line)
Glue spot(Green dot)
Cut along the line.
Glue within the same part.
Insert.
3
Cut in line(solid line) 7
Glue spot(Blue dot)
Cut along the line.
Glue to the rear of the other part.
Scissors, set square, glue(We recommend stick glue), pencil, used
Tools and materials
ballpoint pen, toothpicks, tweezers, (useful for handling small parts)
Before gluing, crease the paper along mountain fold and valley
Assembly tip
fold lines and make sure rounded sections are nice and stiff.
Glue, scissors and other tools may be dangerous to young children
Caution
so be sure to keep them out of the reach of young children.
1
Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
( )
2 Build the fan-shaped foundation.
9
13
10
15
12
14
11
2
Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
Insert
between
( )
3 Build the lower level of the structure.
the folded
25
sides.
21
Insert
between
the folded
sides.
Fold each of parts 21, 22, 24, and 25
before gluing them to part 17.
* Since folding these parts after gluing them
24
to part 17 may cause the paper on the exterior
to stick out or tear, be sure to glue these parts in
place after folding them.
Match the borders
of the coloring when
gluing these pieces together.
19
18
17
Insert
between
the folded
sides.
Match the borders
of the coloring when
gluing these pieces together.
20
16
22
When assembling this section, first attach parts 21, 22, 24,
Insert between
and 25 to part 17, then connect the parts together by adjusting
the folded sides.
the location of the connection between each part.
3
Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
41
Glue in the same way
34
as on the opposite side.
31
30
Glue along the dotted line.
23
33
26
27
Bend this piece slightly
before gluing it.
28
41
Large hall
Glue in the same
way as part 29.
( )
4 Build the large and small halls and the restaurant.
32
35
Assemble parts 33, 35, 38, 45, 52, 55,
and 56 in the same general way.
40
Glue in the same
way as on the opposite
side.
Bend this piece slightly
39
before gluing it.
38
29
Glue together.
36 37
Bend this piece slightly
before gluing it.
37
Glue one side to part 38
40
and one side to part 32.
36
Assemble parts 30, 32, 34, 39, 44,
Glue parts 28, 29, 40, and 41 in place last,
50, 53, 54, 57, and 59 in the same general way.
adjusting the assembled parts while doing so.
4
Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
49
53
47
61
59
Glue in the same way Restaurant
Small hall
Glue in the same 51
as on the opposite side.
60
way as part 46.
54
50
Glue in the same way
55
as on the opposite side.
48
57
Glue in the same way
as on the opposite side.
56
52
45
Bend this piece slightly
44
before gluing it.
Bend this piece slightly
before gluing it.
49
46
Glue in the same way
as on the opposite side.
Bend this piece slightly
58
before gluing it.
Bend this piece slightly
before gluing it.
61
48
43
Glue parts 46, 47, 48, 49, and 61 in place last,
Glue one side to the rear side
42 after assembling all these parts together,
of part 44 and one side
adjusting the assembled parts while doing so.
to part 50.
( )
5 Glue the large and small halls and the restaurant
( ) ( )
to 3 the lower section of the structure 3 .
Small hall
Large hall
Restaurant
( )
3 Lower section of structure
5
Canon is a registered trademark of Canon Inc. Canon Inc.
® ©
Sydney Opera House (Australia): Assembly Instructions
A & A Co., Ltd.
©
( ) ( )
6 Complete the model by gluing the base assembled in step 1 to the foundation assembled
( ) ( )
in step 2 and the structure assembled in step 5 .
( )
5 Structure
( )
2 Foundation
( )
1 Base
Finished!
6