Toy Rubber Band Gun (Simple)


Free Woodworking Plans/Projects - Simple Rubber Band Gun - cached fi... http://www.woodworkersworkshop.com/free-woodworking-plans-archive...
This is 's cache of http://scrollsawyer-exchange.allthingswood.com/plans/rbbrband/RubberBandGun.htm
's cache is the snapshot of this page as we reviewed this "Simple Rubber Band Gun" free woodworking
projects/plans page. Click the link above to see the current page, if it is still active. If it is not active, the cached page below is
the last known record. The page has been cached here due it being reported as being a dead link.
WoodworkersWorkshop.com is not affiliated with the authors of the content on this page nor responsible for the accuracy of
its content.
WoodworkersWorkshop.com recommend's this Woodworking Resource information.
Simple Rubber Band Gun
Compared with sophisticated models to be found on the internet, the gun described here is very simple. That
makes it quick and easy to build and easy to use, even for a five-year-old. If smaller kids are to be involved, be
advised that this gun, or rather its rubber bands, constitute a choking hazard.
The first photo shows the parts of the gun before modification.
1 of 5 05/05/2007 2:33 PM
Free Woodworking Plans/Projects - Simple Rubber Band Gun - cached fi... http://www.woodworkersworkshop.com/free-woodworking-plans-archive...
The barrel is a birch dowel ½ by 91/2 inches.
The handle is scrap hardwood of contrasting color (in this case cherry), ¾ x 1 ź x 3 ¾.
The clothespin is from Rite Aid, 48 for about two bucks.
The trigger is a birch dowel, 3/16 x 1.
The gunsight is a map pin.
The second photo shows the parts modified and ready for assembly.
2 of 5 05/05/2007 2:33 PM
Free Woodworking Plans/Projects - Simple Rubber Band Gun - cached fi... http://www.woodworkersworkshop.com/free-woodworking-plans-archive...
Barrel: a notch is cut in the end to hold the rubber band. A flat spot about 3 inches long is cut on the bottom, to
glue the clothespin to (hard to see in the photo, but the flat spot is just above the clothespin). To install the sight,
drill hole near the end of the barrel with a high number drill (#56??). Install the pin, clip off the point, bend over
the tag end and hammer flat.
Handle: The angle from the side to the top is 65 degrees. To bore the hole for the barrel at the same angle, tip the
drill press table or make a wedge-shaped jig. Use a Forstner bit. Roundovers on all edges of the handle were
done a a foam-padded drum (similar to an inflatable drum).
Clothespin: The notch behind the jaws of the clothespin is enlarged on a scrollsaw. The opposite end(s) of the
clothespin are shortened, the lower leg a bit more than the upper. The trigger is glued in a hole bored in the
lower leg.
The third photo shows two completed guns, one loaded with a single shot and the other with six shots. The gun
works well with size #32 rubber bands. Other sizes might need a longer or shorter barrel.
3 of 5 05/05/2007 2:33 PM
Free Woodworking Plans/Projects - Simple Rubber Band Gun - cached fi... http://www.woodworkersworkshop.com/free-woodworking-plans-archive...
To load and fire the gun:
Single shot: Squeeze the trigger to open the jaws of the clothes pin. Hang a rubber band in the notch behind the
jaws and release the trigger. Stretch the rubber band forward and hook it in the notch in the end of the barrel.
Aim and fire.
Six shot repeater: Squeeze the trigger and hang six rubber bands in a row in the notch behind the jaws. Release
the trigger. Stretch the rubber band nearest the jaws forward and hook it in the notch in the end of the barrel.
Aim and fire. Repeat. You can get off six well-aimed shots in about 20 seconds.
Shotgun: Load as above. Stretch several rubber bands forward and fire them all at once. Handy for downing
flying insects.
I plan to market this gun in my booth in a craft mall around the holidays, as a stocking-stuffer/impulse item. Cost
per gun is minimal, and with any sort of woodshop the parts can be mass produced very quickly. So the selling
price will be low.
If you have any experience marketing such things, or any ideas or suggestions to make this gun better or easier to
build, please don t hesitate to write. I d really like to hear from you.
Jim Adams
4 of 5 05/05/2007 2:33 PM
Free Woodworking Plans/Projects - Simple Rubber Band Gun - cached fi... http://www.woodworkersworkshop.com/free-woodworking-plans-archive...
derfrelad@worldnet.att.net
5 of 5 05/05/2007 2:33 PM


Wyszukiwarka

Podobne podstrony:
Toy Rubber Band Gun and Target
Aldo Colombini The Band 13 New Effects With Cards & Rubber Bands
simple1
JesteÅ› szalona Sadowsky Band
Simple State Machine Documentation
Burn Rate Models for Gun Propellants
SimpleCalculator csproj FileListAbsolute
Toy Smiley Bank Pattern (scrollsaw)
SimpleFormatter
cantina band star wars
Pirates of the Caribbean Suite Klaus Badelt 34 Concert Band Score and Parts
RÓWNOWAGA THERA BAND
Test Simple Viewer
Julia Talbot Chew Toy
130508081700 vwitn print gun

więcej podobnych podstron