CATALOGUE CARD K4-15-123
Issue 2
MINING INDUCTION MOTORS
SG4 562Y-4
Page 1/1
APPLICATION
The one  speed motors of SG4 562Y-4 type are intended for driving mining machines and equipment, and
especially for driving getting units of combined cutter loaders.
The motors can be used in underground parts of mines and surface installations of the mines, where there are
possible explosion conditions for methane and/ or coal dust.
CHARACTERISTIC FEATURES OF MOTORS
" Induction 3-phase motors with welded single squirrel-cage rotor,
" Explosion-proof construction with flame-proof casing of motor  d - mark I M2 EExd I, equipment ranked as
group I of category M2 according to Directive 94/9/EC,
" The degree of protection IP 55 acc. to PN-EN 60034-5:2002U,
" The motors are cooled by water flowing through the channels of body and bearing disks N and P,
" The form of execution: special flanged execution  IM 4301,
" Basic voltage execution: 3300V  50Hz
After settlement it is possible to execute the motors for other voltage and frequency of 50/60Hz,
" Class of insulation F or H,
" Thermal protection of motors: bimetal sensors NC or posistor sensors PTC,
" Thermometric resistors Pt100 are built in winding and bearings for temperature control,
" Two-inlet terminal box with cable inlet Wk3u/d... produced by Damel for feeder cable and inlet 54232& - M36
produced by Gothe for conductor with auxiliary circuits,
" The motor is equipped with the final link of protection conductor continuity control circuit, mounted in the
terminal box  primary execution: the final link CK-OA (with diode) produced by Damel,
" Feeding and start-up: the motors are intended for feeding from power network  start-up by direct switching on
the voltage,
" The motors adapted for work in temperate climate; after settlement the adaptation for work in tropical climate TA
or TH is possible.
COMPATIBILITY WITH REQUIREMENTS OF STANDARDS
The motors meet requirements of Directive 94/9/EC (ATEX), european harmonized standards and domestic
norms:
- norms for electrical equipment in areas of explosion hazard:
- EN 50014:1997+A1:1999+A2:1999  Polish equivalent PN-EN 50014:2002U,
- EN 50018:2000+A1:2002  Polish equivalent PN-EN 50018:2002U,
- EN 50019:2000  Polish equivalent PN-EN 50019:2002U,
- norms for rotational electric machines:
- EN 60034-1:1998+A1:1998+A2:1999+AC:2000  Polish equivalent PN-EN 60034-1:2001
- domestic norms for induction motors for mining machines:
- PN G-38010:1997 (domestic norm).
CERTIFICATES
The motors have the certificates and permissions:
- certificate EC No KDB 04 ATEX 300X issued by notified Testing Station GIG KDB,
valid on the area of European Union.
File No: 300 kW, 3300V, SG4 562Y-4.doc/2005
Translated by: PTU -DAMAR- Sosnowiec
CATALOGUE CARD K4-15-123
Issue 2
MINING INDUCTION MOTORS
SG4 562Y-4
Page 2/2
TECHNICAL DATA
Table 1
Parameters SG4 562Y-4
Rated power PN [kW] 300
Rated voltage UN [V] 3300
Current at rated voltage IN [A] 67
0,83
Power factor cosĆ
[%] 94,5
Efficiency ·
Rotational speed n [1/min] 1475
Rated moment MN [Nm] 1942
6,0
Multiplicity of start-up current Ik/IN
1,6
Multiplicity of start-up moment Ml/MN
2,2
Multiplicity of critical moment Mmax/MN
Min. flow of cooling water [dm3/min] 15
Mode of operation S1;
S4-60%, 40c/h Jext/JM=1
Rotor moment of inertia JM (without torsional [kgm2] 3,2
shaft)
1450
[kg]
Mass of the motor
1. The parameters of motor: rated current, efficiency, power factor, rotational speed and rated moment relate to
rated load at rated feeding conditions  50Hz.
2. Multiplicities of start-up current , start-up moment and critical moment refer to direct connection of the motor to
the supply network (mains).
3. Jext  inertia moment of motor load referred to the shaft of motor
THERMOMETRIC RESISTORS
BIMETAL TEMPERATURE SENSORS
Pt 100
OR POSISTOR PTC SENSORS
BEARING P WINDING
BEARING N
WINDING
BEARING N
BEARING P WINDING
BEARING N
EK - feeder cable control general
BEARING P
screen terminal
Fig. 1 Diagram of motor connections
Diagram of cooling water circulation
Water inlet M20 x 1,5
BODY
Disk N
Disk P
Water inlet Water outlet
Special plug M38 x
M20 x 1,5 M27 x 2
1,5 with orifice M27x 2
Water outlet
Disk N
Disk P
BODY
Passage plug M38 x 1,5
Fig.2 Diagram of cooling system
File No: 300 kW, 3300V, SG4 562Y-4.doc/2005
Translated by: PTU -DAMAR- Sosnowiec
CATALOGUE CARD K4-15-123
Issue 2
MINING INDUCTION MOTORS
SG4 562Y-4
Page 3/3
Inlet
Water inlet
Inlet
View U
View W
Passage plug
M38x1,5 with
orifice M27x2
View U
View W
8 holes Åš 24
Stopper
Stopper
Water outlet
Special plug
M38x1,5 with
orifice M27x2
Water outlet
Fig.3 Overall and assembly dimensions
CONDITIONS OF OPERATION AND APPLICATION
" Ambient temperature 0÷40oC
" Relative humidity at temperature of 35oC 97÷100%
" Height above the sea level d" 1000m
" Degree of corrosive aggressiveness C acc. to PN-71/H-04651
" Admissible inclination of the shaft axis to level d" 30 o
" Parameters of cooling water at inlet of cooling system
- maximum temperature 30oC
- maximum static pressure 3MPa
" Supply voltage (0,95÷1,05)UN
" Electrical terminal
Power supply connection  mining armour conductor with rubber armour and insulation, multicore, screened for
voltage of 1,9/3,3kV, with section area of cores selected to operating conditions.
Connection of auxiliary circuits of temperature sensors  auxiliary cores of feeder cable or pilot wire with
section area of wires up to 4 mm2.
" Leading the armour conductors to terminal box through cable inlets selected according to the outer diameter of
conductors acc. to table 2.
File No: 300 kW, 3300V, SG4 562Y-4.doc/2005
Translated by: PTU -DAMAR- Sosnowiec
CATALOGUE CARD K4-15-123
Issue 2
MINING INDUCTION MOTORS
SG4 562Y-4
Page 4/4
Table 2
Type of inlet The range of diameters of conductors for cable inlets
Wk3u/d80... 34 ÷ 38 36 ÷ 40 40 ÷ 44 41 ÷ 46 44÷49 48 ÷ 53 52-57
Wk3u/d100... 52-57 55-61 59-65 62-68 68-74
54232...M-36 18 ÷ 21 20 ÷ 24 22 ÷ 26 25 ÷ 28
In case the Orderer does not state the type of cable inlet together with outer diameter of conductor the
motor is delivered with cable inlet determined acc. to table 3, column 2.
OFFER FOR DELIVERIES OF MOTORS
The producer offers motors in primary execution and in options executed against the order from customer
(additional, diversified equipment).
Table 3
Constructional Primary execution Execution against order
characteristic of motor
1 2 3
rated voltage 3300V other voltage
Frequency 50Hz 50/60Hz
class of insulation F H
Thermal
bimetal NC + Pt100 posistor PTC + Pt100
protection  type of sensors
Wk3u/d80... or Wk3u/d100&
Wk3u/d80-48-53
cable inlets 54232& M36.
54232.28-M36
with selected gasket - see table 2
final link CK & appointed by Orderer
CK-0A Damel prod.
of control circuit (acc. to catalogue card K4-15-121)
climatic execution for temperate climate for tropical climate TH or TA
acc. to settlements, it can require
constructional characteristic
 acceptance of the unit certifying the
other than above mentioned
product
The following items are included to the delivered motor by producer:
- running-technical documentation ( RTD - Service Manual of the motor).
- declaration of conformity EC.
ORDERING PROCEDURE
The following data should be stated in the order directed to the address of manufacturer given below:
- type of motor, power
- rated voltage and frequency
- motor execution: preliminary  see table 3 column 2 or execution against order, for which required equipment
and constructional characteristic should be determined acc. to table 3 column 3.
When ordering we recommend to fill up the questionary  Statement of technical data of the motor...  accessible at
internet (web) sites and in Marketing Department of DFME DAMEL.
The producer offers additionally:
- guarantee and after guarantee service,
- delivery of spare parts,
- training of employees in the range of correct maintenance and operating the motor.
Producer reserves the right to implement to the motor changes resulting from technical progress.
DÄ…browska Fabryka Maszyn Elektrycznych DAMEL S. A.
Aleja Józefa Piłsudskiego 2, 41-300 Dąbrowa Górnicza, POLSKA, tel: [phone] do 39
Faks (32) 264-34-26, 264-10-12, http: www.damel.com.pl, email: [e-mail]
File No: 300 kW, 3300V, SG4 562Y-4.doc/2005
Translated by: PTU -DAMAR- Sosnowiec
CATALOGUE CARD K4-15-123
Issue 2
MINING INDUCTION MOTORS
SG4 562Y-4
Page 5/5
Elaboration:  DAMEL  TK/LP/01/2005
File No: 300 kW, 3300V, SG4 562Y-4.doc/2005
Translated by: PTU -DAMAR- Sosnowiec