{5/24/93
created initial NoSubs Processor to .81 format
FIFO stuff not supported
variables: 1 = tools 1st op; 2 = tools last op; 3 = ncCAMs last op
Jim Radcliffe}

{7/29/93, v.81.1, added FIFO handling, JR}
{8/3/93, v.81.2, SameTool WFO, RapidF#, additional FIFO handling, JR}
{9/12/95, v.81.3, FIFO? queries changed to ExitType & ExitFeed calls, WFO MultipleParts, JR}
{5/8/96, v.89, Return to the StrtPos before next iteration of CutAutoCycle Repeats ZshiftOnly, JR}
{6/4/96, v.89.1, minor corrections SeqC, CRCOff & SameTool, JR}

{6/4/96
Initial: Fanuc 6M NoSubs M877.89.1
Created: Fanuc 10M MS MV65 NS Mxxx.89
ForUser: Shredding Systems Inc
Control: Fanuc 10M
Machine: Mori Seiki MV-65
Develop: ComPost 4.21.37, Catalyst68K v3.04.10.C
Comment: New Processor per marked up readout from and conversation with Kevin Clark
Jim Radcliffe}

{10/25/95
Initial: Fanuc 10M MS MV65 NS M152.89
Created: Fanuc 10M MS MV65 NS M152.89.1
Comment: Rearranged commands at end of program.
Jim Radcliffe}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0'
#3 = '*###.###;0'
#4 = '####.####;0'
#5 = '#######0'
#6 = '####^##0'
#7 = '#;'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4)
FORMAT(Program#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF MultipleParts? AND SubComment?
'( PART ' Tag# ' )' EOL
END
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN

ExitType:
IF FIFO?
FeedC
ELSE
RapidC
END
RETURN

ExitFeed:
IF FIFO?
FeedEntC
END
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

StdRapid:
IF LastFeat?
SeqC CRCOffC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC RapidC MoveXYZC CRCOffsetC EOL
END
END
END
RETURN

StdLine: {enables CRC on first call, .70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC CRCOnC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
END
END
RETURN

StdArc:
EACHQuadrant
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
RETURN

ToolPath2: {for AutoCycle element moves}
EACHFeat
IF RapidFeat?
StdRapid
ELSE
IF LineFeat?
StdLine
ELSE
IF ArcFeat?
StdArc
END
END
END
NEXTFeat
RETURN

EntryMove:
IF FeedEntry?
SeqC FeedC ZInC FeedEntC EOL
ELSE
SeqC RapidC ZInC EOL
END
RETURN

CutAutoCycle:
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
SeqC IncValue EOL
IF Repeats? AND ZshiftOnly?
EachRep
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
IF FeedConnect?
SeqC FeedC StrtPosC EOL
ELSE
SeqC RapidC StrtPosC EOL
END
END
END
EntryMove
ToolPath2
IF NOT FeedConnect?
SeqC ExitType PRIME ZCP2 ExitFeed EOL
END
NextRep
ELSE
EntryMove
ToolPath2
END
SeqC AbsOrInc ExitType ZCP2 ExitFeed EOL
SetSRSubXY {restore tool position}
SetSRSubMove
ReSetPass2 {restore for positioning moves}
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
IF NOT FirstFeat?
SeqC
IF FIFO?
Rapid
END
MoveSXYC EOL
END
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
CutAutoCycle
ELSE
SeqC MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
StdRapid
ELSE
IF LineFeat?
StdLine
ELSE
IF ArcFeat?
StdArc
END
END
END
END
NEXTFeat
RETURN

WFOStuff:
IF MultipleParts? AND WorkFixtureOffsets?
SetWFO
ELSE
IF NewWFO?
'G' NewWFO#
ELSE
IF NOT SameTool?
IF NeedWFO1?
'G' NewWFO#
END
END
END
END
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

DoCoolOn:
IF NOT CoolOff?
IF Mist?
'M51'
SetFlag('2')
ELSE
CoolOn
END
END
RETURN

DoCoolOff:
IF Flag?('2')
'M59'
SetFlagF('2')
ELSE
CoolOff
END
RETURN

DoOp:
IF FirstOperation?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
IF FullUp?
SeqC IncValue OfstOff EOL
END
DoOpComments
SeqC WFOStuff EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
IF FullUp?
SeqC OfstOn EOL
END
ELSE
DoOpComments
DoPostScript
Seq AbsOrInc CRCOff DrillOff Plane WFOStuff EOL
CheckPass
SeqC Rapid StrtPos Speed SpinOn PreTool EOL
SeqC OfstOn DoCoolOn EOL
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
{only need to set up for tool change on 1st part}
ELSE
SeqC IncValue OfstOff DoCoolOff EOL
DoEndOpPS
IF ToolChangeAtHome?
SeqC AbsOrInc Rapid Home EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
SeqC ToolChng EOL
END

{Start new Operation}

IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
IF FullUp?
SeqC IncValue OfstOff EOL
END
DoOpComments
SeqC WFOStuff EOL
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
IF FullUp?
SeqC OfstOn EOL
END
ELSE
DoOpComments
DoPostScript
Seq AbsOrInc CRCOff DrillOff Plane WFOStuff EOL
CheckPass
SeqC Rapid StrtPos Speed SpinOn PreTool EOL
SeqC OfstOn DoCoolOn EOL
END
ELSE
IF SameTool?

{Finish off last Operation}

SeqC
IF LAST ProgStop? OR NewToolOffset?
IncValue OfstOff
END
IF LAST ProgStop?
DoCoolOff
ELSE
IF CoolOff? AND LAST NOT CoolOff?
DoCoolOff
END
END
EOL
DoEndOpPS
IF LAST ProgStop?
SeqC 'M0' EOL
END

{Start new Operation}

DoOpComments
DoPostScript
CheckPass
SeqC PlaneC AbsOrInc WFOStuff Rapid StrtPos SpeedC
IF LAST ProgStop?
SpinOn
END
EOL
SeqC
IF LAST ProgStop?
OfstOn DoCoolOn
ELSE
IF NewToolOffset?
OfstOn
END
IF NOT CoolOff? AND LAST CoolOff?
DoCoolOn
END
END
EOL
END
END
END

{ Common Point for All Operations }

ResetCRCNum {call here to reset for each new operation only, call in tool path to reset for each repeat in an operation}
RapidF# {forces the output of a conditional feedrate for each operation}

IF Milling?
SeqC ZCP2C EOL
IF Repeats?
IF ZshiftOnly? AND AutoCycle?
{done in CutAutoCycle called from ToolPath}
ELSE
EACHRep
DoSubComment
IF NOT FirstCycle?
SeqC Connect StrtPos EOL
IF NOT FeedConnect?
SeqC ZCP2C EOL
END
END
END
END
IF NOT AutoCycle?
EntryMove
END
ToolPath
IF Repeats?
IF ZshiftOnly? AND AutoCycle?
{done in CutAutoCycle called from ToolPath}
ELSE
SeqC CRCOffC
IF NOT FeedConnect?
ExitType PRIME ZCP3C
END
ExitFeed EOL
NEXTRep
END
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
SeqC CRCOffC ExitType ZCP3C ExitFeed EOL
END
ELSE
IF Drilling?
IF Repeats?
EACHRep
DoSubComment
END
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# ZDepth# {.81}
ToolPath
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqC 'G80' EOL
IF Repeats?
NEXTRep
END
SeqC RapidC ZCP3C EOL
END
END
RETURN

FinishLastOp:
SeqC IncValue OfstOff DoCoolOff EOL
DoEndOpPS
IF FIRST ToolChangeAtHome?
SeqC AbsOrInc Rapid FirstHome EOL
END
SeqC IncValue 'G28X0Y0' EOL
SeqC Rapid 'X-29.57' EOL
IF ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
SeqC ToolChng EOL
RETURN

DoToolsOps:
EachOp
IF GTEqual? Operation# Recall# Num#('1') AND LTEqual? Operation# Recall# Num#('2')
{Tools1stOp ² op ² ToolsLastOp}
DoOp
END
NextOp
RETURN

NextTools1stOp:
SetNextToolOp Operation#
RETURN

GetToolsOps:
EachOp
IF Equal? Operation# Recall# Num#('1') {if op = Tools1stOp}
IF GreaterThan? NextTools1stOp Recall# Num#('1') {if NextTools1stOp is greater Tools1stOp}
Save# Num#('2') SUB# NextTools1stOp Num#('1') {ToolsLastOp becomes NextTools1stOp less 1}
ELSE {else}
Save# Num#('2') Recall# Num#('3') {ToolsLastOp becomes ncCAMsLastOp}
END
END
NextOp
RETURN

DoTool:
IF NOT Flag?('1')
GetToolsOps
IF WorkFixtureOffsets?
NewWFO
EachWFO
TagInc
DoToolsOps
IncWFO
NextWFO
ELSE
EachPart
TagInc
DoToolsOps
NextPart
END
IF LessThan? Recall# Num#('2') Recall# Num#('3') {if ToolsLastOp < ncCAMsLastOp}
Save# Num#('1') ADD# Recall# Num#('2') Num#('1') {Tools1stOp becomes NextTools1stOp}
ELSE {else}
SetFlag('1') {set DoneFlag}
END
TagInit
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
TagInit
SetFlagF('1') {done flag}
SetFlagF('2') { mist coolant }
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000') {?}
SetMaxFeed('500') {?}
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
' MistCoolant, MCool' EOL
' This is a non-modal command effecting the current operation only.' EOL
' Uses Air Blast, M51, for the current operation.' EOL
' FloodCoolant, FCool' EOL
' This is a non-modal command effecting the current operation only.' EOL
' Uses flood coolant, M8, for the current operation.' EOL
' This is the default setting.' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
SeqC 'M36' EOL { Close Doors }
END
NextOp
IF MultipleParts?
IF AllToolsOnePart?
IF WorkFixtureOffsets?
NewWFO
EachWFO
TagInc
EachOp
DoOp
NextOp
FinishLastOp
IncWFO
NextWFO
ELSE
EachPart
TagInc
EachOp
DoOp
NextOp
FinishLastOp
NextPart
END
ELSE
IF OneToolAllParts?
EachOp
IF FirstOperation?
Save# Num#('1') Operation# {ncCAMs1stOp becomes Tools1stOp}
END
IF LastOp?
Save# Num#('3') Operation# {save ncCAMsLastOp}
END
NextOp
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
FinishLastOp
END
END
ELSE
EachOp
DoOp
NextOp
FinishLastOp
END
SeqC 'M39' EOL { Open Doors }
SeqC EOP EOL
EOR EOL
CloseSub
Post2
IF UseComments?
SetScale('1')
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
END
Close