{Change Comments ***********************************************************}

{9/26/88, Added CRCOffC to rapid up and repeats, same as all other Fadal posts, WFG}
{6/5/89, Changed Maximum Spindle RPM from 10000 to 15000 in Form's 'Numbers' Dialog, JR}
{1/26/90, Updated: Fadal M003.58, to .69 format, JR}
{2/90/90, Updated: Fadal M003.69, to .70 format, JR}
{3/23/90, Changed SetMaxRPM from 10000 to 15000 in Prog, JR}

{4/6/90
Added '01' literal for looping once on CallLab line at ZonlyRepAutoCycle & ZonlyRep subs.
DWB}

{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{8/10/90, Updated: Fadal M003.71m to .74 format, JR}

{4/3/91
Modified: Fadal M003.74m
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}

{* 11/3/93 [cwh]
Modeified: Fadal M003.79m
To: Fadal M003.79.1m
For: Gibbs and Associates

Modified the form so that it could be used with the 32MP and 32MPOL
versions of Catalyst ( Virtual ).
*}

{1/3/95
Updated: Fadal M003.81.79.1m
For: Gibbs & Associates
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.04/Compost 4.21.23
Changes made per Pete Jackson
Updated to Version 4.2 per Fanuc 6M M001.81.2f Format.
Modified to get consecutive sequence numbers thru subroutines:
Changed; Seq to SeqLab, SeqC to SeqLabC and N to N? in MachSpec.
Added Retag
Corrected FORMAT5 from '########;0' to '#######0'.
Added RestoreScale Sub per 4-Axis Post Processor.
Added FIFO? at FinishSub1, AutoCycCutSub2, ZonlyRepAutoCycle subs and end of IF Milling.
Moved UnSkipZ from FinishSub1 to ZOnlyRep where SkipZ is set.
Changed FeedRateC to FeedEntC for FIFO Exit Moves.
Added CkCRC sub for CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Changed logic to output CRCOnC in OneFeat ToolPath.
Added logic to suppress output of CRCOnC on ZMove Feature.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to RapidFeat at ToolPath.
Outputs G40 at all ZMoveOnly Feature Retract blocks.
Added TrackZNO# SPZ# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
SPZ# is affected by SetScale, whereas ZDepth# is not.
DWB}

{7/19/95, Updated Fadal M003.81.3m to .85 version per Fadal M003.85, JR}

{8/15/95,
Fadal M003.85.1m
Added literal '01' after CallMasterNum#
Added support for RigidTap per M610.85
TH}

{
Format: Fadal M003.85.2m
8/28/95
Fixed duplicate call of Cycle command
Changed SeqLab to SeqLabC in rigid tap sections
TH}

{
Format: Fadal M003.85.3m
10/12/95
Added UnTool ToolChng to CloseMP: to reload tool1 at the end of each part. This is a First Tool In Spindle post
TH}

{11/17/95
Modified: Fadal M003.85.3m
For: Gibbs & Associates
Versions: ncCad 4.33.01/ncCAM 4.33.01/ncPost 4.33.08/Catalyst v2.28.04/Compost 4.21.33/1.0a
Changes made per Mike Dziminowicz of Hughes Aircraft Space & Comm.
Limited UnTool ToolChng block to AllToolsOnePart at CloseMP sub.
DWB}

{
Format: Fadal M003.85.5m
11/28/95
Fixed CloseMP so the UnTool ToolChng block will not be output for WFO's if OneToolAllParts
TH}

{1/17/96, Updated .85 to .86 version, MPK}

{3/25/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '#####.###;0.'
#5 = '#######0'
#6 = '#####.###;0.'
#7 = '00'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(CallMasterNum#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF NOT Metric? {CAM file is in English, tools and tool path}
SetScale('25.4') { change to Metric, this is a Metric post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
SeqLabC '* SUB NUMBER: ' Program# EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
SeqLabC '* OPERATION ' Operation# ': ' OperationType$ EOL
END
IF OperationComment?
SeqLabC '* ' OperationComment$ EOL
END
IF WorkGroupComment?
SeqLabC '* ' WorkGroupComment$ EOL
END
IF ToolTypeComment?
SeqLabC '* TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ EOL
END
IF ToolComment?
SeqLabC '* ' ToolComment$ EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLabC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLabC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLabC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLabC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqLabC Feed ZIn FeedEnt EOL
ELSE
SeqLabC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
SeqLabC SubIDF EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
SeqLabC '* WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqLabC CallLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqLabC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqLabC Preset ShiftR EOL
SeqLabC EndSub EOL
CloseSub
SeqLabC Preset UnshiftR EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqLabC SetWFO EOL
SeqLabC CallLab OnePart EOL
IncWFO
NextWFO
ELSE
SeqLabC CallLab Parts EOL
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
IF AllToolsOnePart?
SeqLabC UnTool ToolChng EOL
END
SeqLabC EndSub EOL
CloseSub
SeqLabC WFO1 EOL
ELSE
SeqLabC Preset ShiftP EOL
IF AllToolsOnePart?
SeqLabC UnTool ToolChng EOL
END
SeqLabC EndSub EOL
CloseSub
SeqLabC Preset UnshiftP EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLabC AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
IF NOT ZMove?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
END
END
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqLabC MoveSXYC EOL
SeqLabC CallLab OnePart EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqLabC DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF AutoCycle?
SeqLabC DoAbsOrInc
IF LastFeat?
CRCOffC {.70}
END
RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC {.82}
END
RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqLabC DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLabC DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC FormatArc ArcFeedC EOL
DecelMove2
END
SeqLabC FormatArc DecelFeed EOL
ELSE
SeqLabC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
ELSE
SeqLabC 'E' NewWFO# EOL
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
SeqLabC 'E' NewWFO# EOL
END
END
END
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLabC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SeqLabC AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqLabC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqLabC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Feed IncValue StrtPosC EOL
SeqLabC AbsOrInc
ELSE
SeqLabC Feed
END
ELSE
SeqLabC Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqLabC AbsOrInc ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqLabC Rapid ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLabC CallLab OnePart EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
IF FIFO? {.81}
SeqLabC Feed ZCP2 FeedEnt EOL {.69}
ELSE
SeqLabC Rapid ZCP2 EOL {.69}
END
END {.69}
SeqLabC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLabC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqLabC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqLabC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqLabC CallLab OnePart EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqLabC EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

GetStartOfSameTool:
DoOpComments
DoPostScript
WFOStuff
CheckPass
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('15000')
SetMaxFeed('500')
SetFlagF('1') { Milling ZShiftOnly SepSubs }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
SeqLabC 'O' Program#
IF UseComments? AND ProgramNameComment?
'*' ProgramName$
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
SeqLabC '* ' ProgramComment$ EOL
END
IF FormatNameComment?
SeqLabC '* FORMAT: ' FormatName$ EOL
END
IF TimeComment?
SeqLabC '* ' Date$ ' AT ' Time$ EOL
END
IF MovesComment?
SeqLabC '* OUTPUT IN ' MoveType$ ' MILLIMETERS' EOL
END
IF PartsComment?
SeqLabC '* PARTS PROGRAMMED: ' Parts# EOL
END
IF StartToolComment?
SeqLabC '* FIRST TOOL IN SPINDLE' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
DoOpComments
DoPostScript
SeqLab WFOStuff EOL
IF Drilling? AND RigidTap?
SeqLabC Speed EOL
SeqLabC 'G84.2' EOL
ELSE
SeqLabC Speed SpinOn EOL
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLabC Plane AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLabC StrtPos EOL
END
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqLabC CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF ToolChangeAtHome?
SeqLabC AbsOrInc Rapid Home SpinOff EOL
ELSE
SeqLabC SpinOff EOL
END
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END

{Start new Operation}

SeqLab OpToolID EOL
SeqLabC ToolChng EOL
DoOpComments
DoPostScript
WFOStuff
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLabC Plane AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLabC StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLabC CoolOff EOL
SeqLabC SpinOff EOL
SeqLabC 'M0' EOL

{Start new Operation}

GetStartOfSameTool
IF Drilling? AND RigidTap?
SeqLabC Speed EOL
SeqLabC 'G84.2' EOL
ELSE
SeqLabC Speed SpinOn EOL
END
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
IF NewToolOffset?

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
ELSE

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqLabC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqLabC ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqLabC FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqLabC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLabC AbsOrInc Rapid StrtPos EOL
END
SeqLabC DrillCP EOL
GetCycle
SeqLabC
IF Tap? AND OptCyc1?
'G84.1'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF Tap?
FadalTapF FadalTapQ
ELSE
FeedEnt
END
EOL
IF CallMasterOp?
SeqLabC 'L' CallMasterNum# '01' EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLabC CallLab OnePart EOL
StartSub
ToolPath
SeqLabC EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqLabC 'G80' EOL
SeqLabC RapidC ZCP3C EOL
IF Repeats?
FinishSubG92
END
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqLabC CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqLabC AbsOrInc Rapid FirstHome SpinOff EOL
ELSE
SeqLabC SpinOff EOL
END
IF ProgStop?
SeqLabC 'M0' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqLabC OfstOff UnTool ToolChng EOL
SeqLabC WFOOff EOL
SeqLabC EOP EOL
EndSubs
CloseSub
Post2 {organize Subs into one program}
EOR EOL
'BYE' EOL
Close
ReTag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'* FILE LENGTH: ' FileBytes# ' CHARACTERS' EOL
END
IF FileFeetComment?
'* FILE LENGTH: ' FileFeet# ' FEET' EOL
END
IF FileMetersComment?
'* FILE LENGTH: ' FileMeters# ' METERS' EOL
END
Close
END