{Change Comments ***********************************************************}

{9/26/88, Added CRCOffC to rapid up and repeats, same as all other Fadal posts, WFG}
{6/5/89, Changed Maximum Spindle RPM from 10000 to 15000 in Form's 'Numbers' Dialog, JR}
{1/26/90, Updated: Fadal M003.58, to .69 format, JR}
{2/90/90, Updated: Fadal M003.69, to .70 format, JR}
{3/23/90, Changed SetMaxRPM from 10000 to 15000 in Prog, JR}

{4/6/90
Added '01' literal for looping once on CallLab line at ZonlyRepAutoCycle & ZonlyRep subs.
DWB}

{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{8/10/90, Updated: Fadal M003.71m to .74 format, JR}

{4/3/91
Modified: Fadal M003.74m
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}

{* 11/3/93 [cwh]
Modeified: Fadal M003.79m
To: Fadal M003.79.1m
For: Gibbs and Associates

Modified the form so that it could be used with the 32MP and 32MPOL
versions of Catalyst ( Virtual ).
*}

{1/3/95
Updated: Fadal M003.81.79.1m
For: Gibbs & Associates
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.04/Compost 4.21.23
Changes made per Pete Jackson
Updated to Version 4.2 per Fanuc 6M M001.81.2f Format.
Modified to get consecutive sequence numbers thru subroutines:
Changed; Seq to SeqLab, SeqC to SeqLabC and N to N? in MachSpec.
Added Retag
Corrected FORMAT5 from '########;0' to '#######0'.
Added RestoreScale Sub per 4-Axis Post Processor.
Added FIFO? at FinishSub1, AutoCycCutSub2, ZonlyRepAutoCycle subs and end of IF Milling.
Moved UnSkipZ from FinishSub1 to ZOnlyRep where SkipZ is set.
Changed FeedRateC to FeedEntC for FIFO Exit Moves.
Added CkCRC sub for CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Changed logic to output CRCOnC in OneFeat ToolPath.
Added logic to suppress output of CRCOnC on ZMove Feature.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to RapidFeat at ToolPath.
Outputs G40 at all ZMoveOnly Feature Retract blocks.
Added TrackZNO# SPZ# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
SPZ# is affected by SetScale, whereas ZDepth# is not.
DWB}

{1/3/95
Copied: Fadal M003.81.3m
Created: Fadal LongHand M728.81.3m
For: Gibbs & Associates
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.04/Compost 4.21.23
Changes made per Pete Jackson
Updated to Version 4.2 per LongHand M001.81.3f Format.
DWB}

{2/12/96, Updated .85 number to .86, no changes necessary, MPK}

{3/25/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '#####.###;0.'
#5 = '#######0'
#6 = '#####.###;0.'
#7 = '#'
#8 = 'Ä…#bbbbb.bbb#'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Tag#,5)
FORMAT(Recall#,5)
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(RapidF#,7)
FORMAT(PartShiftX#,8)
FORMAT(PartShiftY#,8)
FORMAT(PartShiftZ#,8)

{Prog Subroutines **********************************************************}

RestoreScale:
IF NOT Metric? {CAM file is in English, tools and tool path}
SetScale('25.4') { change to Metric, this is a Metric post}
END
RETURN

DoPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
SeqLabC '* PART NO. ' Tag# EOL
END
RETURN

DoCycleComment:
IF UseComments? AND SubComment?
SeqLabC '* CYCLE START ' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
SeqLabC '* OPERATION ' Operation# ': ' OperationType$ EOL
END
IF OperationComment?
SeqLabC '* ' OperationComment$ EOL
END
IF WorkGroupComment?
SeqLabC '* ' WorkGroupComment$ EOL
END
IF ToolTypeComment?
SeqLabC '* TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ EOL
END
IF ToolComment?
SeqLabC '* ' ToolComment$ EOL
END
RestoreScale
END
RETURN

BadMPWFOReport:
SetStatusOff
' ' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
'Ä„ NOTE: Even though you have elected to Ä„' EOL
'Ä„ process this file using Multiple Ä„' EOL
'Ä„ Parts with Work Fixtures, there exist Ä„' EOL
'Ä„ non-zero values in the invisible, Ä„' EOL
'Ä„ Equally SpacedÉ fields, as follows: Ä„' EOL
'Ä„ Ä„' EOL
'*****************************************' EOL
IF NotEqual? PartShiftX# Num#('0')
' X axis shift = ' PartShiftX# EOL
END
IF NotEqual? PartShiftY# Num#('0')
' Y axis shift = ' PartShiftY# EOL
END
IF NotEqual? PartShiftZ# Num#('0')
' Z axis shift = ' PartShiftZ# EOL
END
'*****************************************' EOL
'Ä„ Ä„' EOL
'Ä„ Please reset these values to zero as Ä„' EOL
'Ä„ they affect the coordinate values Ä„' EOL
'Ä„ output, starting with Part# 2. Ä„' EOL
'Ä„ Thank You. Ä„' EOL
'Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„Ä„' EOL
' ' EOL
SetStatusOn
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLabC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLabC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLabC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLabC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqLabC FeedC ZInC FeedEntC EOL
ELSE
SeqLabC RapidC ZInC EOL
END
RETURN

GetConnect:
IF FeedConnect?
FeedC
ELSE
RapidC
END
RETURN

ExitMove:
SeqLabC
IF FeedConnect?
IF NOT AutoCycle?
IF NOT NoZMoves?
FeedC ZInC FeedEntC
END
END
ELSE
CRCOffC
IF FIFO? { .81 }
FeedC
ELSE
RapidC
END
PRIME ZCP2C
IF FIFO? { .81 }
FeedEntC
END
END
EOL
RETURN

ExitMove2:
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
RETURN

CycleWarning:
{ NOTE: This Post Processor takes care of Z Clearance. }
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
IF NOT ZMove?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC CkCRC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqLabC CkCRC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLabC CkCRC FeedC MoveXYZC FeedRateC EOL
END
END
RETURN

ToolPath:
EACHFeat
IF PointFeat? { Drilling Only }
SeqLabC MoveSXYZC EOL {.80.01}
ELSE
IF RapidFeat?
IF AutoCycle?
IF LastFeat?
CRCOffC {.70}
END
SeqLabC RapidC MoveXYZC EOL
ELSE
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC {.82}
END
IF XMove? OR YMove? OR ZMove?
SeqLabC RapidC MoveXYZC EOL {.82}
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqLabC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLabC FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC FormatArc ArcFeedC EOL
DecelMove2
END
SeqLabC FormatArc DecelFeed EOL
ELSE
SeqLabC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
IF AutoCycle?
SetAbs
Save# Num#('6') SUB# EPX# CurOriginPosX#
Save# Num#('7') SUB# EPY# CurOriginPosY#
SetInc
END
END
NEXTFeat
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
IF NOT SameTool?
IF WorkFixtureOffsets?
SeqLabC 'E' Recall# Num#('9') EOL
END
END
ELSE
SeqLabC 'E' NewWFO# EOL
END
ELSE
IF NOT SameTool?
IF MultipleParts? AND WorkFixtureOffsets?
SeqLabC 'E' Recall# Num#('9') EOL
ELSE
IF NeedWFO1?
SeqLabC 'E' NewWFO# EOL
END
END
END
END
RETURN

AutoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
SeqLabC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
SeqLabC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
RapidC ZCP2
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN

Milling:
EntryMove
ToolPath
RETURN

XYZRep:
CycleWarning
FindAnyZMoves
EachRep
DoCycleComment
IF FirstCycle?
EntryMove
ELSE
SeqLabC CRCOffC GetConnect StrtPosC EOL
IF FeedConnect?
IF ZShiftOnly?
EntryMove
END
ELSE
IF FeedEntry?
SeqLabC ZCP2C EOL
END
EntryMove
END
END
ToolPath
ExitMove
NextRep
RETURN

NoRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqLabC RapidC MoveSXYC EOL
END
AutoCycCutSub1
Milling
AutoCycCutSub2
NEXTFeat
RETURN

XYZRepAutoCycle:
CycleWarning
EachRep
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqLabC GetConnect MoveSXYC EOL
END
SetAbs
Save# Num#('4') SPX#
Save# Num#('5') SPY#
SetInc
AutoCycCutSub1
Milling
AutoCycCutSub2
SetAbs
TrackXNO# ADD# Recall# Num#('4') Recall# Num#('6')
TrackYNO# ADD# Recall# Num#('5') Recall# Num#('7')
SetAbsOrInc
NEXTFeat
NextRep
RETURN

ZonlyRepAutoCycle:
EACHFeat
DoCycleComment
IF SPXMove? OR SPYMove?
SeqLabC RapidC MoveSXYC EOL
END
AutoCycCutSub1
EachRep
IF FirstCycle?
EntryMove
ELSE
IF NOT FeedConnect?
ExitMove
END
DoCycleComment
IF SPXMove? OR SPYMove?
SeqLabC GetConnect MoveSXYC EOL
END
IF NOT FeedConnect?
EntryMove
END
END
ToolPath
NextRep
AutoCycCutSub2
NEXTFeat
RETURN

DrillStuff:
SeqLabC DrillCP EOL
GetCycle
SeqLabC
IF Tap? AND OptCyc1?
'G84.1'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF Tap?
FadalTapF FadalTapQ
ELSE
FeedEnt
END
EOL
TrackZNO# FIRST SPZ# {.81.2}
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

GetStartOfSameTool:
DoPartCycleComment
DoOpComments
DoPostScript
WFOStuff
CheckPass
RETURN

MasterSub:
IF FirstOperation?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE
IF ToolChangeAtHome?
SetHome
END
DoPartCycleComment
DoOpComments
DoPostScript
SeqLab WFOStuff EOL
IF Drilling? AND RigidTap?
SeqLabC Speed EOL
SeqLabC 'G84.2' EOL
ELSE
SeqLabC Speed SpinOn EOL
END
CheckPass
SeqLabC Plane AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
ELSE

{Finish off last Operation}

SeqLabC CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND WorkFixtureOffsets?
SeqLabC 'G' Recall# Num#('8') EOL
END
DoEndOpPS
IF ToolChangeAtHome?
SetAbs
LoadFeat
SUB# HomeX# CurOriginPosX#
SUB# HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqLabC AbsOrInc Rapid MoveXY SpinOff EOL
ELSE
SeqLabC SpinOff EOL
END
IF LAST ProgStop?
SeqLabC 'M0' EOL
ELSE
SeqLabC ProgStop EOL
END

{Start new Operation}

SeqLab OpToolID EOL
SeqLabC ToolChng EOL
DoPartCycleComment
DoOpComments
DoPostScript
WFOStuff
IF Drilling? AND RigidTap?
SeqLabC Speed EOL
SeqLabC 'G84.2' EOL
ELSE
SeqLabC Speed SpinOn EOL
END
CheckPass
SeqLabC Plane AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLabC CoolOff EOL
SeqLabC SpinOff EOL
SeqLabC 'M0' EOL

{Start new Operation}

GetStartOfSameTool
IF Drilling? AND RigidTap?
SeqLabC Speed EOL
SeqLabC 'G84.2' EOL
ELSE
SeqLabC Speed SpinOn EOL
END
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
IF NewToolOffset?

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC OfstOn EOL
ELSE

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
END
END
END {common point for all operations}
RapidF# { No Output }
IF Milling?
SeqLabC ZCP2C EOL
IF AutoCycle?
IF Repeats?
IF ZShiftOnly?
ZonlyRepAutoCycle
ELSE
XYZRepAutoCycle
END
IF NOT FeedConnect?
SeqLabC ExitMove2 EOL
END
ELSE
NoRepAutoCycle
SeqLabC ExitMove2 EOL
END
ELSE { NOT AutoCycle }
IF Repeats?
XYZRep
ELSE
Milling
END
SeqLabC CRCOffC ExitMove2 EOL
END
ELSE
IF Drilling?
IF Repeats?
EachRep
DoCycleComment
IF FirstCycle?
DrillStuff
END
ToolPath
NextRep
ELSE
DrillStuff
ToolPath
END
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqLabC 'G80' EOL
SeqLabC RapidC ZCP3C EOL
END
END
RETURN

EndPartSub:
{End of program ************************************************************}

{finish last operation}
SeqLabC CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND WorkFixtureOffsets?
SeqLabC 'E' Recall# Num#('8') EOL
END
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SetAbs
LoadFeat
SUB# FIRST HomeX# CurOriginPosX#
SUB# FIRST HomeY# CurOriginPosY#
Num#('0') { Dummy Z }
SeqLabC AbsOrInc Rapid MoveXY SpinOff EOL
ELSE
SeqLabC SpinOff EOL
END
IF ProgStop?
SeqLabC 'M0' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqLabC ProgStop EOL
END
END
RETURN

MPLoop:
TagInit
IF AllToolsOnePart?
Save# Num#('9') Recall# Num#('8') { NewWFO# }
EachPart
TagInc
EachOp
MasterSub
NextOp
EndPartSub
Save# Num#('9') ADD# Recall# Num#('9') Num#('1') { NewWFO# }
NextPart
ELSE { OneToolAllParts }
Save# Num#('2') Recall# Num#('1')
IF LTEqual? Recall# Num#('1') Recall# Num#('3')
EachOp
IF Equal? Operation# Recall# Num#('2')
Save# Num#('2') ADD# Operation# Num#('1')
IF NewTool?
IF Equal? Recall# Num#('1') Recall# Num#('3')
Save# Num#('2') Operation#
ELSE
IF NotEqual? Recall# Num#('1') SUB# Recall# Num#('2') Num#('1')
Save# Num#('2') SUB# Operation# Num#('1')
END
END
END
END
NextOp
EachPart
TagInc
EachOp
IF GTEqual? Operation# Recall# Num#('1')
IF LTEqual? Operation# Recall# Num#('2')
IF Equal? Operation# Recall# Num#('1')
IF FirstPart?
Save# Num#('9') Recall# Num#('8') { NewWFO# }
ELSE
Save# Num#('9') ADD# Recall# Num#('9') Num#('1') { NewWFO# }

{Finish off last Operation}

IF FullUp?
SeqLabC CoolOff EOL
END
{DoEndOpPS}

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
IF FullUp?
SeqLabC OfstOn EOL
SeqLabC CoolOn EOL
END
END
END
MasterSub
END
END
NextOp
NextPart
Save# Num#('1') ADD# Recall# Num#('2') Num#('1')
END
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('15000')
SetMaxFeed('500')
Save# Num#('1') Num#('0') { This Tool FirstOp# }
Save# Num#('2') Num#('0') { This Tool LastOp# }
Save# Num#('3') Num#('0') { LastOp# }
Save# Num#('4') Num#('0') { XPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('5') Num#('0') { YPos Status Register Updated Position for Repeated AutoCycles }
Save# Num#('6') Num#('0') { LastFeat EPX# AbsPosValue for Repeated AutoCycles }
Save# Num#('7') Num#('0') { LastFeat EPY# AbsPosValue for Repeated AutoCycles }
Save# Num#('8') Num#('0') { This NewWFO# }
Save# Num#('9') Num#('0') { NewWFO# counter }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EOR EOL
SeqLabC 'O' Program#
IF UseComments? AND ProgramNameComment?
'*' ProgramName$
END
EOL
IF UseComments?
IF ProgramComment?
SeqLabC '* ' ProgramComment$ EOL
END
IF FormatNameComment?
SeqLabC '* FORMAT: ' FormatName$ EOL
END
IF TimeComment?
SeqLabC '* ' Date$ ' AT ' Time$ EOL
END
IF MovesComment?
SeqLabC '* OUTPUT IN ' MoveType$ ' MILLIMETERS' EOL
END
IF PartsComment?
SeqLabC '* PARTS PROGRAMMED: ' Parts# EOL
END
IF StartToolComment?
SeqLabC '* FIRST TOOL IN SPINDLE' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts?
Save# Num#('1') Num#('1')
Save# Num#('8') NewWFO#
IF WorkFixtureOffsets?
IF NotEqual? PartShiftX# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftY# Num#('0')
BadMPWFOReport
ELSE
IF NotEqual? PartShiftZ# Num#('0')
BadMPWFOReport
END
END
END
END
EachOp
IF LastOp?
Save# Num#('3') Operation#
END
NextOp
MPLoop
IF OneToolAllParts?
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
MPLoop MPLoop MPLoop MPLoop MPLoop
EndPartSub
ELSE
IF WorkFixtureOffsets?
SeqLabC 'E' Recall# Num#('8') EOL
END
END
ELSE
EachOp
MasterSub
NextOp
EndPartSub
END
SeqLabC OfstOff UnTool ToolChng EOL
SeqLabC WFOOff EOL
SeqLabC EOP EOL
EOR EOL
'BYE' EOL
Post
Close
ReTag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'* FILE LENGTH: ' FileBytes# ' CHARACTERS' EOL
END
IF FileFeetComment?
'* FILE LENGTH: ' FileFeet# ' FEET' EOL
END
IF FileMetersComment?
'* FILE LENGTH: ' FileMeters# ' METERS' EOL
END
Close
END