{
MILL=T
LATHE=F
SIMPLE_ROT_POS=F
ROTARY_MILL=F
ADV_MILL=T
SUBS=T
MILLTURN_POLAR-SEG=F
MILLTURN_Y-AXIS=F
METRIC=F
}

{Change Comments ***********************************************************}

{9/24/92
Copied & modified: Fanuc 10M [PP] M451.81.2
For: B&C
Customer documentation was poor, and the new information that was added to the end of the
prog was moved down below the 'M99' command.
KM}

{8/18/93
Modified: Seikos M2 HS [BC] M517.81.3
For: B&C
Changes made per conversations with Rick Parks at B&C
Updated to Version 4.1 per Fanuc 6M M001.81.2 Format.
Changed Tap Cycle from G84 to G841 in Composts Drill Cycles Dialog.
This is Direct Rigid Tapping.
Added PostScript OptionalCycle1 for G84 Canned Tap Cycle at Drilling.
Modified output of WorkFixtureOffsets for MultipleParts at openMP.
Configured to output following values, (read from left to right):
G54 G55 G56 G57 G58 G59
G540 G550 G560 G570 G580 G590
G541 G551 G561 G571 G581 G591
G542 G552 G562 G572 G582 G592
G543 G553 G563 G573 G583 G593
G544 G554 G564 G574 G584 G594
G545 G555 G565 G575 G585 G595
G546 G556 G566 G576 G586 G596
G547 G557 G567 G577 G587 G597
G548 G558 G568 G578 G588 G598
G549 G559 G569 G579 G589 G599
DWB}

{9/28/95, Updated Seikos M2 HS [B&C] M517.81.4 to .85 format per Fanuc 6M M001.85.01.03, JR}
{2/9/96, created B style Advanced Mill Version per Fanuc 6M (FW) B001.10.02, JR}

{2/13/96
Initial: Seikos M2 HS [B&C] B517.10.02
Created: Seikos M3 HS [SKS] Bxxx.10.02
ForUser: SKS Machining
Control: Seikos M3
Machine: Hitachi Seiki VK45 with Yuasa Indexer
Develop: ComPost 4.21.33, Catalyst68K v3.0C
Comment: New Processor per marked up readout from Patrick Smolarek.
Deleted literal 'M0' from beginning of program.
Changed literal 'X0Y0' at beginning of first tools to StrtPos.
Changed SpinOn to GetSpinOn.
Outputs M13 for SpinOn and CoolOn.
Outputs M3 if CoolOn was not specified.
Deleted CoolOn except where needed in SameTool.
Added literal 'M123' at end of tools.
Does a full spindle retract
Turns off the spindle
Turns off the coolant
Changed EOP output from M99 to M30.
Indewxer is commanded by M code 70
Combined cSAngleA & cSAngleB
Jim Radcliffe}

{2/16/96, Updated .10 to .11 version
Fixed taping cycles pre customer
removed M15 & g91 line per customer.
JM}

{3/25/96, Tested zonlyRepAutoCycle, Changed version # to .12, MPK}

{4/3/96,
Initial: Seikos M3 HS [SKS] B932.12
Created: Seikos M3 HS [SKS] B932.12.1
Changed tapping cycle (not rigid) to G81, as per customer fax, MPK}

{4/4/96
Initial: Seikos M3 HS [SKS] B932.12.1
Created: Seikos M3 HS [SKS] B932.12.2
Undid my earlier change, added Cycle to drilling section, changed IF Tap? AND OpCyc1?
to IF RigidTap?, MPK}

{7/16/98,
Initial : Seikos M3 HS [SKS] B932.12.2
Created: Seikos M3 HS [SKS] B932.12.3
Customer: Gibbs & Associates

Changes to "Prog":

1. Changed IF WFOCS? OR Flag?('2') to IF Flag?('2') OR WFOCS? in 3 places.
JHE}

{7/16/98,
Initial : Seikos M3 HS [SKS] B932.12.3
Created: Seikos M3 HS [ADB] BU47.15
Customer: ADB Industries, Hector Morales 818/845-6964

Changes to "Prog":

1. Force the output of Rapid & ZCP3 after drilling.
2. Added CoolOff (M9), SpinOff (M5) and OfstOff before TC, ProgStop, and End.
Also added OfstOff before NewToolOffset and ChangeCS.
3. Changed rotary output from M70 to standard B-Style.
4. Changed output between Op1, Op2 etc. subs per .15 standard.
JHE}

{22Mar99
Original: Seikos M3 HS [ADB] BU47.15
Created: Seikos M3 HS [ADB] DU47.16
For: ADB Industries
Changes made per: Hector Morales
Develop: Catalyst 5.05/ComPost2 1.7b15
Added Post Header Comment at the top of Prog.
Updated to .16 D-Style Advanced Mill per Fanuc 6M [NW] D001.16.1
Charles Winston}

{Prog Numeric Format Definitions ****}

#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*#####.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(TrackXNO#,4)
FORMAT(TrackYNO#,4)
FORMAT(TrackZNO#,4)
FORMAT(Trunc#,5)
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(CSSubID#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)

{Prog Subroutines ****}

restoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DefaultWFO:
IF NeedWFO1?
WFO1
END
RETURN

cSPartNum#:
ADD# MUL# NumOfCS# SUB# PartNum# Num#('1') CS#
RETURN

CalcCSWFO#:
DIV# ADD# cSPartNum# Num#('5') Num#('6')
RETURN

cSGroup#:
ADD# Trunc# CalcCSWFO# Num#('0')
RETURN

cSGValue#:
ADD# MUL# SUB# CalcCSWFO# cSGroup# Num#('6') Num#('54')
RETURN

cSGroupValue#:
ADD# cSGroup# Num#('-2')
RETURN

cSWFO:
'G' cSGValue#
IF LessThan? cSGroupValue# NUM#('0')
ELSE
cSGroupValue#
END
RETURN

CalcWFO#:
DIV# ADD# PartNum# Num#('5') Num#('6')
RETURN

Group#:
ADD# Trunc# CalcWFO# Num#('0')
RETURN

PlaceValue#:
Sub# CalcWFO# Group#
RETURN

Position#:
Trunc# Add# Num#('0.01') Mul# PlaceValue# Num#('6') { Trunc# requires rounding up }
RETURN

GValue#:
ADD# Position# Num#('54')
RETURN

GroupValue#:
ADD# Group# Num#('-2')
RETURN

doWFO:
'G' GValue#
IF LessThan? GroupValue# NUM#('0')
ELSE
GroupValue#
END
RETURN

wFO:
DefaultWFO
RETURN

wFOStuff:
IF Flag?('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF NOT SameTool?
IF WFOCS?
cSWFO
ELSE
dowFO
END
ELSE
IF WFOCS?
IF ChangeCS?
IF MultipleParts?
{MP ChangeCS is handled in subCSMP and closeMP}
ELSE
cSWFO
END
END
END
END
END
SetFlagF('2') { Do not output WFO second time wFOStuff is called for MP-WFO-OTAP-ECP }
RETURN

cSG52:
SeqC 'G52X' CSOffsetX# 'Y' CSOffsetY# 'Z' CSOffsetZ# EOL
RETURN

g52Stuff:
IF NOT Flag?('7') AND NOT WFOCS?
IF FirstOperation? OR NewTool? OR ChangeCS?
IF MultipleParts?
IF WorkFixtureOffsets?
cSG52
END
ELSE
cSG52
END
END
END
RETURN

doCSComment:
'( CS#' CS# ' - ' CSComment$ ' )' EOL
RETURN

doCSWFOComment:
IF FirstOperation? OR NewTool? OR ChangeCS?
'( ' cSWFO '= X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ#
IF Flag?('6') { TRUE = B-Style Output, FALSE = C-Style Output }
IF AAxisAvail?
' A' CSOffsetA#
END
IF BAxisAvail?
' B' CSOffsetB#
END
END
' )' EOL
END
RETURN

cSComments:
doCSComment
IF WFOCS? AND NOT MultipleParts?
doCSWFOComment
END
RETURN

doSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

doOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
restoreScale
cSComments
END
RETURN

cSAngleA:
IF AAxisAvail?
IF Flag?('6') AND WFOCS? { TRUE = B-Style Output, FALSE = C-Style Output }
'A0.'
ELSE
'A' CSOffsetA#
END
END
RETURN

cSAngleAC:
IF AChange?
cSAngleA
END
RETURN

cSAngleB:
IF BAxisAvail?
IF Flag?('6') AND WFOCS? { TRUE = B-Style Output, FALSE = C-Style Output }
'B0.'
ELSE
'B' CSOffsetB#
END
END
RETURN

cSAngleBC:
IF BChange?
cSAngleB
END
RETURN

pSInit:
NewWFOF
FourthCWF
FourthCCWF
FifthCWF
FifthCCWF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

pSStuff:
RETURN

doPostScript:
pSInit
EachPS
SeqC PostScript EOL
pSStuff
NextPS
RETURN

doEndOpPS:
pSInit
EachEOPS
SeqC EndOpPS EOL
pSStuff
NextPS
RETURN

entryMove:
IF FeedEntry?
SeqC Feed ZIn
IF FirstOperation? OR NewTool?
FeedEnt
ELSE
FeedEntC
END
EOL
ELSE
SeqC RapidC ZIn EOL
IF FirstOperation? OR NewTool?
RapidF# { Forces FeedRate }
END
END
RETURN

startSub:
OpenSub
SubID EOL
doSubComment
RETURN

subWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

stdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
startSub
RETURN

finishSub1: {part 1}
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

finishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

absValueC:
IF NOT AbsValue?
AbsValue
END
RETURN

incValueC:
IF AbsValue?
IncValue
END
RETURN

absOrIncC:
IF AbsoluteMoves?
absValueC
ELSE
incValueC
END
RETURN

toggleIncDecWFO:
IF Flag?('3') { Incrementing WFOs in effect }
SetFlagF('3')
ELSE { Decrementing WFOs in effect }
SetFlag('3')
END
RETURN

doWFOOps:
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
ELSE
SeqC doWFO EOL
END
SeqC SubCall CallLab RepLab OnePart EOL
RETURN

openMP:
NewProg
IF WorkFixtureOffsets?
IF WFOCS?
startSub
SaveCSProg
SaveCSOpStart
ELSE
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
END
IF Flag?('3') { Incrementing WFOs in effect }
NewWFO
EachWFO {simple eachPart}
doWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE { Decrementing WFOs in effect }
LastWFO
EachWFO {simple eachPart}
doWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4') { This post supports IncWFO/DecWFO }
toggleIncDecWFO
ELSE
NewWFO {reset to WFO1}
END
startSub
END
ELSE
SeqC SubCall CallLab RepLab Parts EOL
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
startSub
END
RETURN

doCSWFOOps:
EachCSOp
doCSWFOComment
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
ELSE
SeqC cSWFO EOL
END
SeqC SubCall CallLabB CSSubID# RepLab OnePart EOL
NextCSOp
RETURN

closeMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
IF WFOCS?
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
END
IF Flag?('3') { Incrementing WFOs in effect }
NewWFO
EachWFO {simple eachPart}
doCSWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE { Decrementing WFOs in effect }
LastWFO
EachWFO {simple eachPart}
doCSWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4') { This post supports IncWFO/DecWFO }
toggleIncDecWFO
ELSE
NewWFO {reset to WFO1}
END
END
ELSE
SeqC absOrIncC EOL
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

subCSMP:
IF WFOCS?
IF ChangeCS?
SeqC EndSub EOL
CloseSub
NewProg
startSub
SaveCSProg
END
END
RETURN

doAbsOrInc:
IF Flag?('1') { Milling ZShiftOnly SepSubs/DrillSubs activated }
IF ZMove?
incValueC
ELSE
absOrIncC
END
END
RETURN

doDrillAbsOrInc:
IF Flag?('1') { DrillSubs activated }
IF SPZMove?
incValueC
ELSE
absOrIncC
END
END
RETURN

restoreAbsOrInc:
IF Flag?('1') { Milling ZShiftOnly SepSubs/DrillSubs activated }
SeqC absOrIncC EOL
END
RETURN

formatArc:
doAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN

ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN

getACEPXY:
SetACSPCompF
Save# Num#('1') SPX# { Status Register Variable for X Axis }
Save# Num#('2') SPY# { Status Register Variable for Y Axis }
SetACSPComp
RETURN

setSRXYtoACEP:
SetPass1
SetSRXYtoEP
LoadFeat Num#('0') Num#('0') Num#('0')
TrackXNO# ADD# Recall# Num#('1') SPX# { Status Register Variable for X Axis }
TrackYNO# ADD# Recall# Num#('2') SPY# { Status Register Variable for Y Axis }
RETURN

toolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
IF LastFeat?
getACEPXY
END
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC doDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC doAbsOrInc ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
SeqC doAbsOrInc ckCRC FeedC MoveXYZC FeedRateC ckCRCNum EOL
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
SeqC formatArc ArcFeedC EOL
NEXTQuadrant
END
END
END
END
NEXTFeat
restoreAbsOrInc
RETURN

autoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
startSub
SetSRXYtoSP
SeqC incValueC EOL
RETURN

autoCycCutSub2: {part 2}
toolPath
SeqC absOrIncC CRCOffC
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

autoCycPat:
SetPass2 {position pattern}
toolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

milling:
IF AutoCycle?
NewProg
autoCycCutSub1
entryMove
autoCycCutSub2
autoCycPat
ELSE
entryMove
toolPath
END
RETURN

g92Sub:
subWarning
stdSub
SeqC absOrIncC Connect StrtPos EOL
milling
finishSub1
finishSubG92
RETURN

doSepSubZMoves:
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusInc EOL
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FirstCycle? AND AutoCycle?
Rapid
END
SeqC RapidC ZInPlusInc EOL
END
END
SeqC SubCall CallLab EOL
IF NOT FeedConnect? AND NOT AbsValue?
TrackZNO# ZCP2PlusInc#
SeqC ZCP2C EOL
IF NOT AutoCycle?
TrackZNO# ClearancePlane3#
END
END
RETURN

setSepSubZ:
TrackZNO# ADD# FIRST SPZ# MUL# RepsLess1# RepeatZ#
RETURN

zonlyRepAutoCycle:
autoCycPat {write pattern moves and main calls}
startSub
NewProg
EachCycle
SetSRXYtoEP
IF NOT FirstCycle?
Connect
IF SPXMove? OR SPYMove?
SeqC incValueC StrtPosC EOL
absOrIncC
END
END
SetStatusOn
doSepSubZMoves
SetStatusOff
NextCycle
SetStatusOn
autoCycCutSub1 {build element sub}
TrackZNO# FIRST SPZ#
autoCycCutSub2
IF FeedConnect?
IF NOT AbsValue?
setSepSubZ
END
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

zonlyRep:
EachCycle
SetSRXYtoEP
IF NOT FirstCycle?
Connect
IF SPXMove? OR SPYMove?
SeqC StrtPosC EOL
END
END
doSepSubZMoves
NextCycle
startSub
TrackZNO# FIRST SPZ#
toolPath
finishSub1
SeqC EndSub EOL
CloseSub
IF FeedConnect? AND NOT AbsValue?
setSepSubZ
END
RETURN

checkPass: {use the correct StrtPos}
IF AutoCycle?
SetPass2
ELSE
SetPass1
END
IF NOT Flag?('7')
ClearCSOffset
END
RETURN

skipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

setDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

opGuts:
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
zonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
SetFlag('1') { Milling ZShiftOnly SepSubs activated }
zonlyRep
SetFlagF('1') { Milling ZShiftOnly SepSubs deactivated }
END {end Auto Cycle IF}
ELSE {not Z only}
g92Sub
END {end Z only IF}
ELSE {no repeat OPs}
milling
END
IF AutoCycle?
SeqC CRCOffC ZCP3C EOL
setSRXYtoACEP
ELSE
IF FIFO?
SeqC FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
SeqC DrillCP EOL
GetCycle
SeqC
IF RigidTap?
'G841'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
IF CallMasterOp?
SeqC SubCall CallLabB CallMasterNum# EOL
skipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') { DrillSubs activated }
NewMasterProg
SeqC SubCall CallLab EOL
startSub
toolPath
SeqC EndSub EOL
CloseSub
SetFlagF('1') { DrillSubs deactivated }
ELSE
toolPath
END
END
setDrillEndOpZ
SeqC Rapid DrillOff ZCP3 EOL
END
END
RETURN

GetSpinOn:
IF CoolOff?
SpinOn
ELSE
'M13'
END
RETURN

progStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('12700')
ELSE
SetMaxFeed('500')
END
Save# Num#('1') Num#('0') { Status Register Variable for X Axis }
Save# Num#('2') Num#('0') { Status Register Variable for Y Axis }
Save# Num#('3') Num#('0') { Status Register Variable for Z Axis }
SetFlagF('1') { Milling ZShiftOnly SepSubs/DrillSubs deactivated }
SetFlagF('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
SetFlag('3') { Incrementing WFOs in effect }
SetFlag('4') { This post supports IncWFO/DecWFO }
SetFlagF('5') { Suppress Redundant WFO for MP-WFO-OTAP-ECP }
SetFlag('6') { TRUE = B-Style Output, FALSE = C-Style Output }
SetFlag('7') { TRUE = D-Style Output }
SetFlag('8') { TRUE = D-Style Output, FALSE = Local G52-WFO Coordinates }
IF PSComment? AND UseComments?
'Utility Data:' EOL
' At Op Start: All literals and commands will appear at the beginning of the operation.' EOL
' At Op End: All literals and commands will appear at the end of the operation.' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' OptionalCycle1, OptCyc1 -' EOL
' will output a G84 Tapping Cycle, instead of G841 Rigid Direct Tapping.' EOL
END

IF NOT Flag?('7')
IF Equal? NumOfCS# Num#('1') { 3 Axis Part - Output M-Style }
SetFlag('7')
ELSE
IF MultipleParts?
IF WorkFixtureOffsets?
IF LTEqual? MUL# Parts# NumOfCS# Num#('66')
SetWFOCS { use WFO for CS changes }
ELSE
IF Flag?('8')
SetFlag('7')
END
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of parts [ ' Parts# ' ] times CSs [ ' NumOfCS# ' ] )' EOL
'( exceeds the machine limit. Switching to '
IF Flag?('7')
'non'
ELSE
'G52'
END
'-wfo style output. )' EOL
END
END
ELSE
SetFlag('7')
END
ELSE
IF LTEqual? NumOfCS# Num#('66') {****}
SetWFOCS { use WFO for CS changes }
ELSE
IF Flag?('8')
SetFlag('7')
END
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of CSs [ ' NumOfCS# ' ] exceeds the machine limit. )' EOL
'( Switching to '
IF Flag?('7')
'non'
ELSE
'G52'
END
'-wfo style output. )' EOL
END
END
END
END
END
RETURN

initOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
restoreScale
RETURN

firstOp1:
IF ToolChangeAtHome?
SetHome
END
doOpComments
Seq OpToolID ToolChng EOL
doPostScript
RETURN

firstOp2:
SeqC wFOStuff EOL
g52Stuff
SeqC Speed GetSpinOn EOL
checkPass
SeqC Rapid Plane AbsOrInc StrtPos PreTool cSAngleA cSAngleB EOL
RETURN

firstOp3:
SeqC OfstOn EOL
RETURN

newToolOp1:
SeqC CoolOff EOL
SeqC Rapid IncValue OfstOff EOL
RETURN

newToolOp2:
SeqC SpinOff EOL
doEndOpPS
IF ToolChangeAtHome?
SeqC absOrIncC Home EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN

newToolOp3: {Start new Operation}
doOpComments
Seq OpToolID ToolChng EOL
doPostScript
RETURN

newToolOp4:
SeqC wFOStuff EOL
g52Stuff
SeqC Speed GetSpinOn EOL
checkPass
SeqC Rapid PlaneC AbsOrInc StrtPos PreTool cSAngleA cSAngleB EOL
RETURN

newToolOp5:
SeqC OfstOn EOL
RETURN

sameToolOp1:
doEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC RapidC IncValue OfstOff EOL
SeqC SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset? OR AChange? OR BChange?
SeqC RapidC IncValue OfstOff EOL
END
END
RETURN

sameToolOp2: {Start new Operation}
doOpComments
doPostScript
checkPass
RETURN

sameToolOp3: {Start new Operation}
SeqC wFOStuff EOL
g52Stuff
IF LAST ProgStop?
SeqC Speed GetSpinOn EOL
SeqC Rapid PlaneC AbsOrInc StrtPos cSAngleA cSAngleB EOL
SeqC OfstOn EOL
ELSE
SeqC Rapid PlaneC AbsOrInc StrtPos SpeedC cSAngleAC cSAngleBC EOL
IF NewToolOffset? OR AChange? OR BChange?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN

end1:
SeqC CoolOff EOL
SeqC Rapid IncValue OfstOff EOL
RETURN

end2:
SeqC SpinOff EOL
doEndOpPS
IF FIRST ToolChangeAtHome? {added FIRST modifier}
SeqC absOrIncC RapidC FirstHome EOL
END
IF Equal? CSOffsetA# Num#('0') AND Equal? CSOffsetB# Num#('0')
ELSE
SeqC absOrIncC
IF AAxisAvail?
cSAngleA
END
IF BAxisAvail?
cSAngleB
END
EOL
SeqC Preset
IF AAxisAvail?
'A0'
END
IF BAxisAvail?
'B0'
END
EOL
END
IF ProgStop?
SeqC 'M0' EOL
END
RETURN

end3:
SeqC UnTool ToolChng EOL
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

mPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
IF FirstOperation?
openMP
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2 {to tool change, CS problem}
subCSMP
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
end2
closeMP
end3
RETURN

mP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
IF FirstOperation?
firstOp1
openMP
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
closeMP
newToolOp2 {to tool change, CS problem}
newToolOp3
openMP
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
closeMP
end2
end3
RETURN

mP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
openMP
firstOp2 {need StrtPos in Sub}
ELSE
IF NewTool?
closeMP
newToolOp1
newToolOp2 {to tool change, CS problem}
newToolOp3
newToolOp4
newToolOp5
openMP
newToolOp4 {need StrtPos in Sub}
ELSE {implied SameTool?}
sameToolOp1
subCSMP
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
closeMP
end1
end2
end3
RETURN

noMPs: {no multiple parts}
EachOp {Start of post processing}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END {common point for all operations}
opGuts
NextOp {loops back to EachOP until last Operation}
end1 {End of program}
end2
end3
RETURN

{Start of executable Prog, Top Level ****}

progStart {setup and initializations}
initOp

IF MultipleParts?
IF AllToolsOnePart?
mPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
mP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
mP1ToollAllPXcp
END
END
ELSE
noMPs
END