76 1
EXTERIOR/INTERIOR TRIM  FRONT BUMPER
FRONT BUMPER
760HX 02
COMPONENTS
Front Bumper Side
Mounting Bracket RH
Front Bumper
Reinforcement
36 (367, 27)
Front Bumper Side
Mounting Bracket LH
36 (367, 27) 5.0 (51, 44 in.Å"lbf)
Radiator Grille
Sub assy
Front Bumper
Energy Absorber
Front Bumper Cover
w/ Fog Light
Front
Bumper
Hole Cover RH
Front Fog Light
Unit RH
x 4
w/
x 4
w/
Retainer
Fog
Retainer
Front
Light
Spoiler
Front Fog Light
Unit LH w/ Front Spoiler
Front RH Spoiler Sub assy Front Bumper Front LH Spoiler Sub assy
Hole Cover LH
NÅ"m (kgfÅ"cm, ftÅ"lbf)
: Specified torque
B58775
2004 COROLLA (RM1037U)
Author : Date : 1856
76 2
EXTERIOR/INTERIOR TRIM  FRONT BUMPER
760HY 02
REPLACEMENT
HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.
1. REMOVE RADIATOR GRILLE SUB ASSY
(a) Remove the 2 bolts and clip.
(b) Using a screwdriver, remove the radiator grille.
HINT:
Tape the screwdriver tip before use.
B59104
2. REMOVE FRONT BUMPER COVER
(a) Remove the 6 screws and 2 clips.
Hook
(b) Disengage the hook, and remove the front bumper cover.
(c) w/ Fog light:
Disconnect the fog light connectors.
3. REMOVE FRONT BUMPER ENERGY ABSORBER
B59105
4. REMOVE FRONT BUMPER REINFORCEMENT
(a) Disconnect the wire harness clamp.
(b) Remove the 4 nuts and front bumper reinforcement.
B59112
5. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET LH
6. REMOVE FRONT BUMPER SIDE MOUNTING BRACKET RH
7. REMOVE FRONT LH SPOILER SUB ASSY (W/ FRONT SPOILER)
(a) Remove the screw and 4 retainers.
(b) Disengage the clip and front LH spoiler.
(c) Employ the same manner described above to the other side.
8. REMOVE FRONT RH SPOILER SUB ASSY (W/ FRONT SPOILER)
9. REMOVE FOG LIGHT UNIT LH (W/ FOG LIGHT)
(a) Remove the nut and fog light unit.
(b) Employ the same manner described above to the other side.
10. REMOVE FOG LIGHT UNIT RH (W/ FOG LIGHT)
11. REMOVE FRONT BUMPER HOLE COVER LH (W/O FOG LIGHT)
12. REMOVE FRONT BUMPER HOLE COVER RH (W/O FOG LIGHT)
2004 COROLLA (RM1037U)
Author : Date : 1857
76 3
EXTERIOR/INTERIOR TRIM  FRONT BUMPER
13. INSTALL FRONT BUMPER REINFORCEMENT
(a) Install the front bumper reinforcement with the 4 nuts.
Torque: 36 NÅ"m (367 kgfÅ"cm, 27 ftÅ"lbf)
B59112
14. INSTALL RADIATOR GRILLE SUB ASSY
(a) Install the radiator grille with the 2 bolts and clip.
Torque: 5.0 NÅ"m (51 kgfÅ"cm, 44 in.Å"lbf)
B59244
2004 COROLLA (RM1037U)
Author : Date : 1858
76 4
EXTERIOR/INTERIOR TRIM  REAR BUMPER
REAR BUMPER
760HZ 02
COMPONENTS
Luggage Compartment Trim Cover Inner RH
Rear Bumper Luggage Compartment
Side Seal LH Trim Cover Inner LH
Spare Wheel
5.5 (56, 49 in.Å"lbf) Cover Assy
Rear Bumper
Side Seal RH
Rear Floor Finish Plate
Rear Bumper
36 (367, 27)
Arm RH
Rear Bumper Arm LH
36 (367, 27)
Rear Bumper
Reinforcement No. 1
36 (367, 27)
Rear Bumper
Reinforcement No. 2
Rear Bumper
Energy Absorber
Bumper Mounting Set
Bolt No. 1
Rear Bumper Cover
x 5
Retainer
w/ Rear Spoiler
x 5
Retainer
Rear No. 2 Spoiler Sub assy Rear No. 1 Spoiler Sub assy
NÅ"m (kgfÅ"cm, ftÅ"lbf)
: Specified torque
B58776
2004 COROLLA (RM1037U)
Author : Date : 1859
76 5
EXTERIOR/INTERIOR TRIM  REAR BUMPER
760I7 02
REPLACEMENT
HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.
1. REMOVE SPARE WHEEL COVER ASSY
2. REMOVE REAR FLOOR FINISH PLATE
(a) Remove the 3 clips.
(b) Using a moulding remover, remove the rear floor finish
plate.
B59106
3. REMOVE LUGGAGE COMPARTMENT TRIM COVER
INNER LH
(a) Remove the 4 clips and the luggage compartment trim
cover.
(b) Employ the same manner described above to the other
side.
4. REMOVE LUGGAGE COMPARTMENT TRIM COVER
INNER RH
B59107
5. DISCONNECT REAR BUMPER SIDE SEAL LH
(a) Remove the clip and a part of the rear bumper side seal,
as shown in the illustration.
HINT:
Do not remove the lower side clip.
(b) Employ the same manner described above to the other
side.
6. DISCONNECT REAR BUMPER SIDE SEAL RH
B59109
7. REMOVE REAR BUMPER COVER
(a) Remove the 4 nuts.
B59108
2004 COROLLA (RM1037U)
Author : Date : 1860
76 6
EXTERIOR/INTERIOR TRIM  REAR BUMPER
(b) Remove the 2 screws and 6 clips.
(c) Disengage the hook, and remove the rear bumper cover.
Hook
B59110
8. REMOVE REAR BUMPER ENERGY ABSORBER
9. REMOVE REAR BUMPER REINFORCEMENT NO.2
(a) Remove the rear bumper reinforcement No. 2 from the rear bumper energy absorber.
10. REMOVE REAR NO.2 SPOILER SUB ASSY (W/ REAR SPOILER)
(a) Remove the 5 retainers, screw and the rear spoiler.
(b) Employ the same manner described above to the other side.
11. REMOVE REAR NO.1 SPOILER SUB ASSY (W/ REAR SPOILER)
12. REMOVE BUMPER MOULDING SET BOLT NO.1
13. REMOVE REAR BUMPER REINFORCEMENT NO.1
(a) Remove the 4 nuts and rear bumper reinforcement No. 1.
14. REMOVE REAR BUMPER ARM LH
(a) Remove the 3 bolts and rear bumper arm.
(b) Employ the same manner described above to the other side.
15. REMOVE REAR BUMPER ARM RH
16. INSTALL REAR BUMPER ARM LH
(a) Install the rear bumper arm with the 3 bolts.
Torque: 36 NÅ"m (367 kgfÅ"cm, 27 ftÅ"lbf)
(b) Employ the same manner described above to the other side.
17. INSTALL REAR BUMPER ARM RH
18. INSTALL REAR BUMPER REINFORCEMENT NO.1
(a) Install the rear bumper reinforcement No. 1 with the 4 nuts.
Torque: 36 NÅ"m (367 kgfÅ"cm, 27 ftÅ"lbf)
19. INSTALL REAR BUMPER COVER
(a) Install the rear bumper cover with the 2 screws, 8 clips and 4 nuts.
Torque: 5.5 NÅ"m (56 kgfÅ"cm, 49 in.Å"lbf) for nuts
2004 COROLLA (RM1037U)
Author : Date : 1861
76 7
EXTERIOR/INTERIOR TRIM  REAR SPOILER
REAR SPOILER
760I1 02
REPLACEMENT
HINT:
Installation is in the reverse order of the removal. But the installation is indicated only when it has a point.
1. REMOVE LUGGAGE COMPARTMENT DOOR COVER
2. REMOVE REAR SPOILER
(a) Remove the 2 screws.
(b) Disconnect the wire harness connector.
(c) Put protective tape.
(d) Using a heat light, heat the spoiler to 40  60_C (104 
140_F).
(e) Tie both piano wire ends to a wooden block or a similar
object.
(f) Scrape the spoiler protector off by pulling the piano wire
Protective Tape
as shown in the illustration.
NOTICE:
S If reusing the rear spoiler, take care not to damage the
rear spoiler.
S Do not damage the body and wire harness.
Clip
B59776
(g) Remove the 2 clips, wire harness grommet and rear spoil-
Clip er.
3. REMOVE CENTER STOP LAMP ASSY
(a) Remove the 2 bolts and the center stop lamp assembly.
Clip
4. INSTALL REAR SPOILER
(a) Using a heat light, heat the body mounting surface to 40
 60_C (104  140_F).
NOTICE:
Do not heat the body excessively.
B59775
(b) Remove the protective tape from the body.
(c) Wipe off the stains with cleaner.
(d) Clean the rear spoiler (if reusing the rear spoiler).
(1) Using a heat light, heat the rear spoiler to 40  60_C
(104  140_F).
NOTICE:
Do not heat the rear spoiler excessively.
(2) Remove the rear spoiler protector from the rear
spoiler.
(3) Wipe off the stains with cleaner.
2004 COROLLA (RM1037U)
Author : Date : 1862
76 8
EXTERIOR/INTERIOR TRIM  REAR SPOILER
(4) Install 4 new rear spoiler protectors to the rear spoil-
Rear Spoiler Protector RH
er as shown in the illustration.
Rear Spoiler Protector LH
Rear Spoiler Side Protector RH
Rear Spoiler Side Protector LH
B59774
2004 COROLLA (RM1037U)
Author : Date : 1863
76 9
EXTERIOR/INTERIOR TRIM  NAME PLATE
NAME PLATE
760HU 02
REPLACEMENT
3 4
1 2
1 Luggage Compartment Door Name Plate No. 1 2 Luggage Compartment Door Name Plate No. 2
16.5 (0.65)
83.4 (3.28)
15.4 (0.61)
14.8 (0.58)
End of R shape
3 4 Luggage Compartment Door Plate No. 4
End of R shape End of R shape
13.6 (0.54) 14 (0.55)
15.8 (0.62)
20.3 (0.80)
mm (in.)
B59289
2004 COROLLA (RM1037U)
Author : Date : 1864
76 10
EXTERIOR/INTERIOR TRIM  OUTSIDE MOULDING
OUT SIDE MOULDING
7610C 02
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
1. REMOVE OUTSIDE MOULDING
Protective
(a) Put protective tape around the moulding.
Tape
(b) Insert a piano wire between the vehicle body and mould-
ing.
(c) Tie objects that can serve as handles (for example, wood-
en blocks) to all wire ends.
(d) Pull the piano wire and scrape off the double sided tape
that holds the moulding to the vehicle body.
NOTICE:
B57422
S If reusing the moulding, take care not to damage the
moulding.
S Becareful not to damage the body.
(e) Remove the moulding.
2. INSTALL OUTSIDE MOULDING LH
(a) Using a heat light, heat the body.
Heating temperature: 40 to 60_C (104 to 140_F)
NOTICE:
Do not heat the body excessively.
(b) Remove the double sided tape from the body.
(c) Wipe off the stains with cleaner.
(d) Clean the moulding (if reusing).
(1) Using a heat light, heat the body.
Heating temperature: 20 to 30_C (68 to 86_F)
NOTICE:
Do not heat the moulding excessively.
(2) Remove the double sided tape from the moulding.
(3) Wipe off the stains with cleaner.
(4) Apply new adhesive tape to the moulding as shown
in the illustration.
Double sided Tape
B59015
2004 COROLLA (RM1037U)
Author : Date : 1865
76 11
EXTERIOR/INTERIOR TRIM  OUTSIDE MOULDING
(e) Using a heat light, heat the body and moulding.
Heating temperature:
Item Temperature
Body 40 to 60_C (104 to 140_F)
Moulding 20 to 30_C (68 to 86_F)
NOTICE:
Do not heat the body and moulding excessively.
(f) Remove the peeling paper from the double sided tape on
the moulding face.
NOTICE:
When the peeling paper is removed, take care that no dirt
or dust contaminates the adhesive.
(g) Affix the moulding to the body, as shown in the illustration.
NOTICE:
Do not apply excessive force onto the moulding. Use
steady pressure with your thumbs.
2.6 (0.10)
1.5 (0.059)
26 (1.02)
26 (1.02)
300 (11.81)
66 (2.60)
190 (7.48)
223 (8.78) 233 (9.17)
240 (9.45)
mm (in.)
B59794
2004 COROLLA (RM1037U)
Author : Date : 1866
76 12
EXTERIOR/INTERIOR TRIM  FRONT DOOR BELT MOULDING ASSY LH
FRONT DOOR BELT MOULDING ASSY LH
760I8 02
REPLACEMENT
HINT:
S The installation procedures are the removal procedures in reverse order.
S Use the same procedures for the RH side and LH side.
1. REMOVE FRONT ARMREST ASSY LH (See page 75 7)
2. REMOVE POWER WINDOW REGULATOR MASTER SWITCH ASSY (W/ POWER WINDOW)
(See page 75 7)
3. REMOVE FRONT ARMREST BASE PANEL UPPER LH (W/O POWER WINDOW)
(See page 75 7)
4. REMOVE FRONT DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75 7)
5. REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH LH (See page 75 7)
6. REMOVE FRONT DOOR TRIM BOARD SUB ASSY LH (See page 75 7)
7. REMOVE FRONT DOOR BELT MOULDING ASSY LH
(a) Put protective tape under the weatherstrip.
(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.
HINT:
Tape the moulding remover tip before use.
Tape
Tape
Moulding Remover
B72676
2004 COROLLA (RM1037U)
Author : Date : 1867
76 13
EXTERIOR/INTERIOR TRIM  REAR DOOR BELT MOULDING ASSY LH
REAR DOOR BELT MOULDING ASSY LH
760I5 02
REPLACEMENT
HINT:
S The installation procedures are the removal procedures in reverse order.
S Use the same procedures for the RH side and LH side.
1. REMOVE REAR ARMREST ASSY LH (See page 75 20)
2. REMOVE POWER WINDOW REGULATOR SWITCH ASSY REAR (W/ POWER WINDOW)
(See page 75 20)
3. REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSY (W/O POWER WINDOW)
(See page 75 20)
4. REMOVE REAR DOOR TRIM BOARD SUB ASSY LH (See page 75 20)
5. REMOVE REAR DOOR BELT MOULDING ASSY LH
(a) Put protective tape under the weatherstrip.
(b) Using a moulding remover, pry out the weatherstrip as
shown in the illustration.
HINT:
Tape the moulding remover tip before use.
Tape
Tape
Moulding Remover
B72677
2004 COROLLA (RM1037U)
Author : Date : 1868
76 14
EXTERIOR/INTERIOR TRIM  BODY ROCKER PANEL MOULDING LH
BODY ROCKER PANEL MOULDING LH
760I0 02
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
1. REMOVE BODY ROCKER PANEL MOULDING LH
(a) Remove the 8 retainers.
(b) Using a screwdriver, remove the moulding.
Clip
HINT:
Tape the screwdriver tip before use.
(c) Remove the 7 clips from the moulding.
Retainer
B59781
2. INSTALL BODY ROCKER PANEL MOULDING LH
(a) Install the moulding with 7 new clips.
New
(b) Install the 8 retainer to the moulding.
Clip
Retainer
B59781
2004 COROLLA (RM1037U)
Author : Date : 1869
76 15
EXTERIOR/INTERIOR TRIM  SIDE MUDGUARD SUB ASSY LH
SIDE MUDGUARD SUB ASSY LH
760I4 02
REPLACEMENT
HINT:
Use the same procedures for the RH side and LH side.
1. REMOVE SIDE MUDGUARD SUB ASSY LH
(a) Using a clip remover, remove the 8 retainers and 9 clips.
(b) Using a moulding remover, remove the mudguard.
Retainer
Clip
B59782
2. INSTALL SIDE MUDGUARD SUB ASSY LH
New Clip
(a) Install the mudguard with 9 new clips.
(b) Install the 8 retainers to the mudguard.
Retainer
Clip
B59782
2004 COROLLA (RM1037U)
Author : Date : 1870
76 16
EXTERIOR/INTERIOR TRIM  LUGGAGE COMPARTMENT DOOR GARNISH
OUTSIDE
LUGGAGE COMPARTMENT DOOR GARNISH OUTSIDE
760I3 02
REPLACEMENT
HINT:
The installation procedures are the removal procedures in reverse order. However, only installation proce-
dures requiring additional information are included.
1. REMOVE LUGGAGE COMPARTMENT LOCK CYLINDER & KEY SET
(a) Remove the 2 nuts and luggage compartment lock cylinder.
2. REMOVE LUGGAGE COMPARTMENT DOOR
Clip
GARNISH OUTSIDE
(a) Remove the nut.
(b) Remove the 4 clips and garnish.
B58077
3. INSTALL SYMBOL EMBLEM
(a) Using white gasoline, clean the garnish installation surface.
(b) Using a heat light, heat the garnish and emblem to 20 to 30_C (68 to 86_F).
NOTICE:
Do not heat the garnish and emblem excessively.
(c) Install the emblem with the 4 clips.
2004 COROLLA (RM1037U)
Author : Date : 1871
76 17
EXTERIOR/INTERIOR TRIM  ROOF DRIP SIDE FINISH MOULDING CENTER LH
ROOF DRIP SIDE FINISH MOULDING CENTER LH
760I2 02
REPLACEMENT
HINT:
S Use the same procedures for the RH side and LH side.
S The installation procedures are the removal procedures in reverse order. However, only installation
procedures requiring additional information are included.
1. REMOVE ROOF DRIP SIDE FINISH MOULDING
Clip
CENTER LH
(a) Apply protective tape onto the circumference of the
moulding for protection.
(b) Using a remover for the roof moulding, release the en-
gagements of the clips both in the front and rear ends of
the moulding. Then remove the moulding.
NOTICE:
Tape
S Do not remove the clips.
B58072
S If clips are damaged during removal or removed acci-
dentally, replace them.
2. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP
NO.1
Front Side
NOTICE:
15 (0.59)
Step 2 should be performed only when replacing the clips.
(a) Remove the double sided tape that remains on the
mounting surface of the body, and then clean the surface
with white gasoline.
(b) Using a heat light, heat the clip installation surfaces of the
body.
Heating temperature:
Item Temperature
Rear Side
Body 40 to 60_C (104 to 140_F)
17 (0.67) Moulding 20 to 30_C (68 to 86_F)
NOTICE:
Do not heat the body and moulding excessively.
(c) Set new clips in the positions as shown in the illustration,
and press fit those clips by hand to install them.
HINT:
mm (in.)
B59795
Clips for the roof drip side finish moulding are supply parts.
(d) After press fitting the clips, wait at last 30 minutes. Then
install the moulding.
HINT:
S Initial hardening time: 30 minutes
S Prefect hardening time: 24 hours
2004 COROLLA (RM1037U)
Author : Date : 1872
76 18
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
ROOF HEADLINING ASSY
760HV 02
COMPONENTS
Front Door Opening Trim RH
Center Pillar Garnish RH
Front Pillar Garnish RH
Rear Door Opening Trim RH
Roof Side Garnish Inner RH
Fixed Type Rear Seat
Rear Seat Side Cover RH
Package Tray
Trim Panel Assy
Rear Door Scuff Plate RH
Separated Type
41.2 (420, 30)
Rear Seat
Center Pillar Garnish
Room Partition Board RH
Lower RH
Front Door
Roof Side Garnish Inner LH
Scuff Plate RH
Rear Door Opening Trim LH
Sholder Anchor
Cover Cap
Center Pillar Garnish LH
41.2 (420, 30)
Room
Cowl Side Trim Board RH
Partition
Board LH
Front Pillar Garnish LH
Rear Seat
Front Door Opening Trim LH
Side Cover LH
Rear Door Scuff Plate LH
Room Partition Board LH
Center Pillar Garnish Lower LH
Front Door Scuff Plate LH
Cowl Side Trim Board LH
: Specified torque
NÅ"m (kgfÅ"cm ftÅ"lbf)
B59264
2004 COROLLA (RM1037U)
Author : Date : 1873
76 19
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
w/ Sliding Roof
Assist Grip Sub assy
Assist Grip Sub assy
Roof Headlining Assy
RH Visor Assy
Assist Grip Sub assy
Assist Grip Sub assy
Visor Holder
LH Visor Assy
Sun Roof Opening Trim Moulding
Room Lamp Assy No.1
Lamp Lens and Cover
Lens Cover
Map Lamp Assy
B59298
2004 COROLLA (RM1037U)
Author : Date : 1874
76 20
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
w/o Sliding Roof
Assist Grip Sub assy
Assist Grip Sub assy
Roof Headlining Assy
RH Visor Assy
LH Visor Assy
Assist Grip Sub assy
Visor Holder
Room lamp Assy No.1
Lens Cover
B59265
2004 COROLLA (RM1037U)
Author : Date : 1875
76 21
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
760HW 02
REPLACEMENT
1. REMOVE FRONT DOOR SCUFF PLATE RH
(a) Using a screwdriver, remove the front door scuff plate RH.
HINT:
Tape the screwdriver tip before use.
2. REMOVE FRONT DOOR SCUFF PLATE LH
B59266
3. REMOVE REAR DOOR SCUFF PLATE RH
(a) Using a screwdriver, remove the rear door scuff plate RH.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
4. REMOVE REAR DOOR SCUFF PLATE LH
B59267
5. REMOVE COWL SIDE TRIM BOARD RH
(a) Remove the clip.
(b) Using a screwdriver, remove the cowl side trim board RH.
Clip
HINT:
Tape the screwdriver tip before use.
(c) Employ the same manner described above to the other
side.
6. REMOVE COWL SIDE TRIM BOARD LH
B59268
7. REMOVE FRONT DOOR OPENING TRIM RH
8. REMOVE FRONT DOOR OPENING TRIM LH
9. REMOVE REAR DOOR OPENING TRIM RH
10. REMOVE REAR DOOR OPENING TRIM LH
11. REMOVE CENTER PILLAR GARNISH LOWER RH
(a) Pull the center pillar garnish lower RH upward to remove
it.
(b) Employ the same manner described above to the other
side.
12. REMOVE CENTER PILLAR GARNISH LOWER LH
B50588
2004 COROLLA (RM1037U)
Author : Date : 1876
76 22
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
13. REMOVE CENTER PILLAR GARNISH RH
(a) Using a screwdriver, remove the shoulder anchor cover
cap.
HINT:
Tape the screwdriver tip before use.
(b) Remove the bolt and front seat outer belt shoulder an-
chor.
(c) Remove the bolt and front seat outer belt floor anchor.
B55754
(d) Using a screwdriver, remove the center pillar upper gar-
nish RH.
Clip
HINT:
Tape the screwdriver tip before use.
(e) Employ the same manner described above to the other
side.
14. REMOVE CENTER PILLAR GARNISH LH
B50773
15. REMOVE REAR SEAT CUSHION ASSEMBLY (See page 72 6, 72 8)
16. REMOVE REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72 8)
17. REMOVE REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72 6)
18. REMOVE REAR SEAT SIDE COVER RH (FIXED TYPE
REAR SEAT)
(a) Using a screwdriver, remove the rear seat side cover RH.
HINT:
Clip
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
side.
19. REMOVE REAR SEAT SIDE GARNISH LH (FIXED
TYPE REAR SEAT)
B59299
20. REMOVE ROOM PARTITION BOARD LH
Built in Clip
(SEPARATED TYPE REAR SEAT)
(a) Remove the 2 clips and 2 built in clips room partition
board LH.
Clip
21. REMOVE ROOM PARTITION BOARD RH
(SEPARATED TYPE REAR SEAT)
(a) Remove the clip and 2 built in clips room partition board
RH.
B59277
2004 COROLLA (RM1037U)
Author : Date : 1877
76 23
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
22. REMOVE ROOF SIDE GARNISH INNER RH
(a) Using a screwdriver, remove the roof side garnish inner
RH.
HINT:
Tape the screwdriver tip before use.
Clip (b) Employ the same manner described above to the other
side.
23. REMOVE ROOF SIDE GARNISH INNER LH
B59566
24. REMOVE PACKAGE TRAY TRIM PANEL ASSY
(a) Using a clip remover, remove the 7 clips.
(b) Pull out the belt from the slit and then remove the package
tray trim panel assembly.
B59276
25. REMOVE FRONT PILLAR GARNISH RH
(a) Using a screwdriver, remove the front pillar garnish RH.
HINT:
Tape the screwdriver tip before use.
(b) Employ the same manner described above to the other
Clip
side.
26. REMOVE FRONT PILLAR GARNISH LH
B59269
27. REMOVE RH VISOR ASSY
(a) Remove the 2 screws and RH visor assembly.
28. REMOVE LH VISOR ASSY
B59270
2004 COROLLA (RM1037U)
Author : Date : 1878
76 24
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
29. REMOVE MAP LAMP ASSY (W/ SLIDING ROOF)
(a) Remove the screw.
(b) Using a screwdriver, remove the map lamp lens and cov-
er.
HINT:
Tape the screwdriver tip before use.
(c) Remove the screw.
(d) Using a screwdriver, remove the glove box lamp assem-
bly.
HINT:
Tape the screwdriver tip before use.
B59271
30. REMOVE ROOM LAMP ASSY NO.1
(a) Using a screwdriver, remove the lens cover.
(b) Using a screwdriver, remove the room lamp assembly
No.1 as shown in the illustration.
B59272
31. REMOVE ASSIST GRIP SUB ASSY
(a) Using a screwdriver, remove the 2 assist grip covers.
(b) Remove the 2 screws and assist grip sub assy.
B50594
2004 COROLLA (RM1037U)
Author : Date : 1879
76 25
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
32. REMOVE VISOR HOLDER
90_
(a) Remove the holder of the sun visor by turning it counter-
clockwise.
B50596
33. REMOVE SUN ROOF OPENING TRIM MOULDING (W/ SLIDING ROOF)
34. REMOVE ROOF HEADLINING ASSY
w/ Sliding Roof
(a) Remove the 3 clips and roof headlining assembly.
w/o Sliding Roof
Clip
B59278
B59931
B59273
2004 COROLLA (RM1037U)
Author : Date : 1880
76 26
EXTERIOR/INTERIOR TRIM  ROOF HEADLINING ASSY
35. INSTALL ROOF HEADLINING ASSY
w/ Sliding Roof
(a) Align the markings, and then install the wire harness with
tape.
Tape
HINT:
Be careful for dirt or foreign objects not to stick to the adhered
part when peeling off the double stick tape.
(b) Attach the roof wire harness across the adhered part.
NOTICE:
Roof wire harness should be attached securely.
(c) Install the 3 clips.
w/o Sliding Roof
Tape
B59275
B59930
B59274
36. INSTALL ROOM PARTITION BOARD RH (SEPARATED TYPE REAR SEAT)
37. INSTALL ROOM PARTITION BOARD LH (SEPARATED TYPE REAR SEAT)
38. INSTALL REAR SEAT SIDE COVER RH (FIXED TYPE REAR SEAT)
39. INSTALL REAR SEAT SIDE GARNISH LH (FIXED TYPE REAR SEAT)
40. INSTALL REAR SEAT BACK ASSY (FIXED TYPE REAR SEAT) (See page 72 8)
41. INSTALL REAR SEAT BACK ASSY (SEPARATED TYPE REAR SEAT) (See page 72 6)
2004 COROLLA (RM1037U)
Author : Date : 1881