GSM/GPRS/GPS TRACKER

MANUAL

UPreface

Thank you for purchasing the tracker. This manual shows how to operate the device smoothly and correctly. Make sure to read this manual carefully before using this product. Please note that specification and information are subject to changes without prior notice in this manual. Any change will be integrated in the latest release. The manufacturer assumes no responsibility for any errors or omissions in this document.

Contents

1. Summary

Working Based on existing GSM/GPRS network and GPS satellites, this product can locate and monitor any remote targets by SMS or internet. Device is transmitting data by inspecting vibration of device.

2. Application

• Protect child / the old / the disabled / pet etc

• Provide peace-of-mind for businessmen

• Personnel Management

• Criminals Tracking

3 Usage

3.1 SIM card installation

Make sure that there is no call transfer and call display is on, and PIN code off. The SMS message must in Text format, can't be identified for PDU format.

3.2 Battery and Charger

Do charge the battery to capacity in 8 -12 hours for first time. Please use the battery and charger provided by the manufacturer. This unit adopts built-in Li-ion battery, and full battery can standby 48 hours. After first use, the battery usually should be charged fully in 10 hours.

3.3. Startup

• Put the SIM card in SIM card slot, device will start automatically, red light keep stable lighting, device light turns off and enter into power-saving mode after 5 minutes.

• In 10 - 40 seconds, the unit will begin to work and acquire the GSM signal as well as the GPS signal and start normal working.

• Device has GPS and LBS two working mode, when in GPS mode, device must be put open outside.

• For first use, please initialize the unit and restore it to default setting.

• When device can work normally, you can use it and do any setting as the instructions of this manual.

• Device Parameter Settings

4.1 Initialization

Send SMS “SBCZ” to the tracker, it will reply “RESET OK” and initialize all the settings. (Default password: 000000).

Remark: initialization is resetting all the parameters to factory defaults.

4.2 Set password

4.2.1Set Password: Send SMS: “#mm#old password#new password#” to the unit to change the password.

For Example, send SMS: “#mm#000000#123456#” to device, it will reply SMS: “MM OK”.

4.2.2 Make sure the new password is in 6 digits arabic numbers, or the device cannot recognize the password.

4.3 Authorization

Please set authorization number before using, it has 2 numbers can be set.

1. Send SMS “#BD#1#000000#number#” to set up first authorized number; send SMS “#BD#2#000000#number#” to set up second

authorized number device will reply “BD OK”.

4.4 Mode switch between GPS and LBS

4.4.1 Send SMS“#DW1#”, device will switch to GPS mode.

4.4.2 Send SMS “#DW2#”, device will switch to LBS mode.

4.5 Single Locating

4.5.2Send SMS“123” (LBS mode), it will reply address: around 118m, jianhui rd, bao'an district, Shenzhen, China.

4.5.3 Send SMS“321” (GPS mode), it will reply a real-time

Google link message as below:

https://maps.google.com/maps?q=N22.669973,E114.011467

4.6 Voice Surveillance

Dialing device number, device will get though and enter into voice listening mode.

4.7 Geo-fence

4.7.1 Set up: When the unit stays immobile in a place, send SMS “#WL#semidiameter#”, device will reply “WL OK”. In case of breach, it will send SMS “Geo-fence alert” to the authorized number.

4.7.2 Cancel: Send SMS “GWL” to deactivate this function, it will reply “GWL OK”.

4.8 Vibration alarm

4.8.1 Set up: When the unit stays immobile in a place, send SMS “kzd”, device will reply “KZD OK”. In case of vibration happened, it will send SMS “Vibration alert” to the authorized number and make a call to authorized number .

4.8.2 Cancel: Send SMS “gzd” to deactivate this function, it will reply “GZD OK”.

4.9 SOS alarm

Press the SOS for 3 seconds, it will send “SOS Alarm” to the authorized number.

4.10 GPRS setting

User must send SMS via cell phone to set IP, port and APN before starting GPRS.

4.10.1 Setting APN

4.10.1.1 APN standards for Access Point Name and differs from country to country. For more information about the local APN, inquiry from your local GPRS network operator.

4.10.1.2 Send SMS “#apn#password#APN content#APN user name#APN password#”, device will reply “APN OK”.

E.g. send SMS command “#apn#000000#cmnet#”.

Notes: CMNET is the APN content of China Mobile (it has no APN user name and password).

4.10.2 IP and Port setting

Send SMS “#IP#ip address#port number#”. If succeeded, device will reply SMS “IP OK”

Note: “IP” in SMS must be capital letter.

4.11 Check device setting

Send SMS “cx” to device, it device will reply as below:

4.12 Device restart

Send SMS “SBCQ” to device, it device will reply “ RESTART OK”.

---