Suzuki RM250 9

Suzuki RM250 9



14 GENERAL INFORMATION

A WARNING


*    Proper semce and repair procedures are important for the safety ot the service mechanic and the safety and reliability of the motorcycle.

*    When 2 or morę persons work together, pay attention to the safety of each other.

*    When handling toxic or flammable materials, make surę that the area you work In Is well-venti-lated and that you follow all of the materiał manufacturer’s instructions.

*    Never use gasoline as a cleaning solvent.

*    After servicing the fuel, oil, exhaust or brake systems, check all lines and fittings related to the system for leaks


_CAUTION_

*    If parts replacement is necessary, replace the parts with Suzuki Genuine Parts or their equiva-lent.

*    When removing parts that are to be reused, keep them arranged in an orderly manner so that they may be reinstalled in the proper order and orientation.

*    Be surę to use the special tools when instructed.    \

*    Make surę that all parts used in reassembly are clean. Lubricate them when specified.

*    Use the specified lubricant, bond, or sealant.    \

*    Whenever you remove oil seals, gaskets, packing, O-rings, locking washęrs, self-locking nuts, circlips and certain other parts as specified, bę śure tp replace them with new ones. Also, before installing these new parts, be surę to remóye ąńy lęft ,over materiał from the mating

surfaces.    \V\ \ <"

\ . . w \ \ \

*    Never reuse a circlip. When installing a new ęlręljp* take care not to expand the end gap larger than required to slip the circlip dyer the śhaft After installing a circlip, always ensure that it is completely seated in its grooye and sećurely fitted.

*    Use a torque wrench tó tighten bblts/niitś to the specified torque. Wipe off grease and oil if a

thread is smeared with them. i ') l

/ ,

*    After reassembling, chectc parts for tightness and proper operation.

*    Use special tools where specified.


*    To protect the em/ironment, do not unławfully dispose of used motor oil and other fluids.

*    To protect Earth’s natural resources, properly dispose of used motorcycle and parts.



Wyszukiwarka

Podobne podstrony:
49586 Suzuki RM250 1-10 GENERAL INFORMATIONSTOPPING THE ENGINE 1)    Shift the trans
79430 Suzuki RM250 8 GENERAL INFORMATION 1-3 GENERAL INFORMATION 1-3 A WARNING A WARNING Fuel can ca
Suzuki RM2508 14-6 FRONT AND REAR BRAKESBRAKE DISC INSPECTION • Measure the front and rear brake di
12121 Suzuki RM2506 14-14 FRONT AND REAR BRAKESREAR MASTER CYLINDER REASSEMBLY Reassemble and remou
suzuki rm25001 9-14 FUEL SYSTEM 9-14 FUEL SYSTEM 14 - 6 kQTHROTTLE POSITION SENSORINSPECTION • Disc
suzuki rm25036 14-4 FRONT AND REAR BRAKES •    Remove the reservoir cap. •  &nb
suzuki rm25038 14-6 FRONT AND REAR BRAKESBRAKE DISC INSPECTION • Measure the front and rear brake d
suzuki rm25040 14-8 FRONT AND REAR BRAKESREAR CALIPER REMOVAL AND DISASSEM-BLY •    
suzuki rm25042 14-10 FRONT AND REAR BRAKES 14-10 FRONT AND REAR BRAKESREAR CALIPER REASSEMBLY Reass
suzuki rm25044 14-12 FRONT AND REAR BRAKES •    Remove the diaphragm. •   
suzuki rm25046 14-14 FRONT AND REAR BRAKESREAR MASTER CYLINDER REASSEMBLY Reassemble and remount th
72010 Suzuki RM2501 9-14 FUEL SYSTEMTHROTTLE POSITION SENSORINSPECTION • Disconnect the throttle po
87472 Suzuki RM2504 14-2 FRONT AND REAR BRAKESCONSTRUCTION H 10 N-m (1.0 kgf-mt 7.0 Ib-ft) H 23 N-m
33596 Suzuki RM2500 14-8 FRONT AND REAR BRAKES 14-8 FRONT AND REAR BRAKES #REAR CALIPER REMOVAL AND

więcej podobnych podstron