tmta1

tmta1



Lining

Lining, Fig 12, PI 1

The lining is normally cut to the same shape as the outer layer of the garment. If you don't use a complete pattern for the garment cut the outer materiał and use this as a pattern for the lining.

Make up the lining separately. Put it inside the garment with the wrong sides together, smoothing the layers and pinning them along the seams (Fig 12, Pl 1). Turn in the seam allowances round the edges, tack the two layers together and stitch them from the right side. This method will avoid the hag-like effect, especially for large hems, that can be produced by machining in the lining from the wrong side.

For doublets with eyelets round the lower edge, cut extra seam allowances on the outer materiał and fold this to the inside for 2-3 cm. Make the lining correspondingly shorter (Fig 12).

For long garments with wide hems it is best to pin or tack the lining in as described, leaving them on a hanger or dress-stand overnight to let the skirts drop. Stitch the lining into the neck and armholes, and sleeves; lay the garment fiat and smooth the two layers together, matching the seams and pinning if necessary for their whole length. Trim both layers level, leaving 3-5 cm seam allowance, and turn in the two edges before stitching them together. If you prefer, fold the lining slightly shorter than the outer fabric and hem it down. Despite the length it is still worth finishing the hem by hand: if the lining eventually starts to sag and show round the edge it is easier to unpick.

Lining close-fitting sleeves An alternative lining method for close-fitting set-in sleeves, as on a doublet (Doublets, Fig 9), is to make up each sleeve with its lining, finish off the wrist edge and the shoulder puff (if included), and set the completed sleeves into the armholes.

Make up the lining of the body and pin it into the outer layer; turn in the seam allowances round the armholes, and hem the lining into place. This is a good alternative with any set-in sleeve.

Facings

Facings are used to neaten edges on the inside of unlined garments. The medieval tailor used narrow facing strips, cut on the straight grain, sińce shaped ones were unknown. Being narrow they could be eased round curved edges without much difficulty.

12

12. Lining

The inside of a doublet with the lining pinned in place. Pin, tack, and stitch the lining to the garment round the collar, waist seam and armholes before hemming or top-stitching the edges. Shorten the lining at the lower edge so that the eyelets (to attach hose) can be worked through the unlined folded edge.

Use narrow strips of linen or plain silk, perhaps 3 cm wide (with narrow seam allowances), but allow enough width for any buttonholes. Join the strip to the garment edge at the fitting linę on the right side of the fabric, turn it to the inside and hem down the folded edge. Fig 21 shows a faced edge with buttonholes.

51


Wyszukiwarka

Podobne podstrony:
tmta1 9. Modelling joined hose Prepare the toile and fit each leg as described for separate hose an
carving?ce Fig. 13 Fig. 14The Basic Face 13 One morę smali area is removed, Fig. 12, and the face i
23745 tmta1 1 Platę 6 Early 14th century cote This is similar to Cotes, Fig. 5, in a medium weight
essent?rving?59 Car ved Mo u l dix g s Fig 4.12 After the rim ofthe cup has been stabbed in, a chip
- 12- Hartmann, Sweden meaningful work and training to otherwise idle youth on a rather Iow level of
3 6 Select a keyboard Please select a keyboard. If you don’t find the exact right choice below, plea
scheme Flyback Driver 47 - 200 pH 10A If you don’t have the irfp250’s you can use a couple of semico
Extracting the Install Archive To install MySQL manually, do the following: 1.    If
Jacquard PatternsWeaving In Yarn Carried Across the Back of the Work If you are working large j
Intarsia PatternsFor Attractive Color Changes Jusr as ar rhe heginning of each rew. when you chanie
Ad42456St1Sz1Sq1Id7 K miningco.corrr We minę the Net so you don t have to. allmy

więcej podobnych podstron