317

317



INTERIOR AND EXTERIOR

-Exterior (Cont'd)_

'ts.


F280D


d.


:809A

nark gap

13

'P

strip


168B


4; Roof side molding 1. Install front end cap.


Stud bolt


2. Install rear end of roof side molding.


sealant.


After cleaning-.

bonding surface, After applying apply urethane 1 palant, install


O


molding within 5 minutes.


3. Lightly tap molding into flange. (Be careful not to damage vehicle body.)



4. Insert tip of roof side molding into front end cap.    _



(5), (6) Door molding


To remove, draw out molding by rotating upper side of molding.


Pawi


SBF170B


Z Side guard molding

•    Side guard molding is affixed to body panel with seaiant and doubie-faced adhesive tape. And the repair part is affixed with doubie-faced adhesive tape.

•    Remove it only if it is necessary to do so.

•    Removal:

1. Heat molding portion to 30 to 40°C (86 to 104°F) with a heat gun.



S3F455A

2. Raise end of molding and, while cutting off bonding agent, detach molding.

• Instailation

1.    Remove all traces of bonding agent from body panel. Tfaen clean contact face of body.

2.    Heat body panel and molding to 30 to 40°C (86 to 104° F) with a heat gun. Then install molding.


8 Door weatherstrip

Apply butyl tape where necessary while installing the weatherstrip


SBF1713


(9 Door corner finisher

This is madę of plastic. so handle with care when removing it.


Seal rubber


SBF172B



Wyszukiwarka

Podobne podstrony:
INTERIOR AND EXTERIOR_Interior (Cont d)ROOF TRIM INSTALLATION Affix double-faced adhesive tape to bo
INTERIOR AND EXTERIOR_Exterior (Cont d)_ @ Cowl top sealing rubber (Q), @ Hood front sealing rubber
INTERIOR AND EXTERIOR •    When removing clip or fastener, refer to CLIP & FASTEN
INTERIOR AND EXTERIOR_Exterior_ •    Apply sealing compound where necessary while
DSC08479 Interior spraylng Exterior spraylng Wewnętrzny i zewnętrzni! natrysk Wewnętrzny - dysze
MANUAŁ STEERING GEAR AND LINKAGE — R22TDiassembly (Cont d)__Inspection_ RACK 1. Remove tie-rod inner
SERVICE DATA AND SPECIFICATIONS (S.D.S.)-Chassis and Body Maintenance--(Cont d) TIGHTEIMING
“For each word write only the dots and dashes of the Ts’ and ‘t’s’ it contains and you have—.—for
BATTERY.M.F. Battery Test and Charging Chart (Cont d) Chart II-a CAPACITY TEST M.G. • Check battery
iBATTERYM.F. Battery Test and Charging Chart (Cont d) A: SLOW CHARGE Fig. 2 INITIAL CHARGING CURRENT
BATTERYM.F. Battery Test and Charging Chart (Cont d) Fig. 4 INITIAL CHARGING CURRENT SETTING (Standa
BATTERYM.F. Battery Test and Charging Chart (Cont d) ▼ Go to "CAPACITY TEST". Fig 6 INITIA
44243 Suzuki RM2501 FRONT FORK AND STEERING 15-25STEERINGREMOVAL •    Remove the fro
SGGW Forestry and Wood Technology.- 2011, nr 76, s. 234-242, bibliogr.13 poz. Przydomowe oczyszczaln
BIRLA INSTITUTE OF TECHNOLOGY AND SCIENCE, PILANI Higher Degree Admlssion Test: I Semester 2012-13 -
New Forms Taschen 014 Pages 16/17 Rem Koolhaas Grand Palais Lille, France, 1990-94 Exterio

więcej podobnych podstron