The Reset Glitch Hack Using the Matrix Glitcher 2.
PHAT XBOX360 TUTORIAL
Required Hardware:
•
Matrix Glitcher
•
Matrix NAND Programmer or any other USB SPI Programmer to dump/flash the
Xbox360's NAND
•
Soldering Material
Required Software:
•
Python and Python Crypto
•
NandPro V 2.0e or greater
Identification of NAND Size:
As a first step we should identify the NAND size that is installed into the XBOX360.
The skilled ones can simply read the NAND size directly from the code written on the NAND.
The second solution is to go to the memory tab under the settings menu.
•
If there is no memory unit shown there then you have a 16MB NAND.
•
If there is a Memory Unit showing 214MB then you have a 256MB NAND.
•
If there is a Memory Unit showing 451MB, then you have 512MB NAND.
1
1.Dumping NAND
•
Use the following diagram to solder your NAND Programmer
•
O pen windows' command prompt and Launch NandPro
•
D ump your NAND twice by using the read command for 16MB
NAND :
nandpro
usb: -r16 nanddumpname.bin
2
•
Compare the two dumps with the following command (you can
use MD5 Checksums too) :
fc /b nanddumpname.bin nanddumpname2.bin
•
You should see something like FC: No difference found. If the
two dumps don't match, do a new dump and check again.
3
•
If you have a 256 MB or 512 MB NAND you can run the following
commands:
nandpro usb: -r64 nanddumpname.bin
2 .Installation of Python and Python Crypto
•
Install Python 2.7 (32bit!) with the default settings:
4
•
Install PyCrypto 2.3 with the default settings :
To enable python in windows' command prompt, we will have to modify
the environment variables .
•
Go in Control Panel
>
System
> Advanced System Settings
5
•
Click on Environment variable
6
•
Click on New in system variables
•
A dd this for the name and the value of the variable :
PYTHONPATH
%PYTHONPATH%;C:\Python27;
7
3.Creating the Hack image
•
D ownload the gggggg-hack (from our website or from “Free60-Git Repository”).
•
Put your original NAND dump in the root of the gggggg-folder
and create a folder named “output” (in the root as well).
•
O pen windows' command prompt again and navigate to the
gggggg-folder than type this Python command (don’t forget to
modify it with your NAND dump name) :
python common/imgbuild/build.py nanddumpname.bin
common/cdxell/CD common/xell/xell-gggggg.bin
8
You should see the following
The file image
_00000000.ecc
is located in the output folder now.
9
•
Copy this file into your Nandpro folder and navigate to the
folder via command prompt again
•
Use the following command to flash the image to your console's
NAND.
nandpro usb: +w16 image_00000000.ecc
nandpro usb: +w64 image_00000000.ecc ( 256 and 512 mb ONLY)
/!\ Pay attention that you have to use the +w16 or +w64 switch and not
the -w16 or –w64 one /!\
The flashed file has a size of 50 blocks so you should see 004F when
the flashing is done.
10
4.Wiring and Setting the Glitcher2
•
Select the correct Switch settings on Glitcher2 to enable the FAT model.
•
Select the correct DIP Switch combination correct for your console model:
•
Proceed directly to solder the Matrix Glitcher directly to the XBOX360
motherboard. Use the diagrams that are supplied together with this tutorial.
A copy is available on our website:
WWW.INFINITYMOD.COM
11
5.Fine tuning your console:
The Matrix Glitcher2 has an innovative fine tuning system that allows you to fine tune
your console timings to get the optimal boot rate.
This feature has been mainly developed for installers, but can be used also by end users.
To use this features you will need an external programmer.
People already owning a Freedom PCB can use the External programmer that comes
together with the Freedom PCB.
WARNING:
The Matrix Glitcher2 MUST be installed into the Xbox and the console must be turned ON.
PROCEDURE:
•
Connect the 4 pin flat cable to the Matrix Glitcher2 and to the external programmer.
•
Place the Matrix Glitcher2 in programming mode by placing all the four DIP
switches in the OFF position:
•
Connect the USB cable to the external programmer and to the PC and take note of
the COM port that is assigned to the external programmer.
12
•
Download the “Fine Tuning Software” from our website and unzip it to a folder.
•
Run a DOS session, navigate to the folder where you unzipped the “Fine Tuning
Software” and type the following command:
C:\MtxGL2FineTuning COMxx (where xx is the COM port assigned to the programmer)
This command will check synchronization with the Glitcher 2 and will return the actual
setting value stored into the Glitcher2. The default value is “0”.
For FAT models the significant values can be “-3”, “-2”, “-1”, “0”, “+1”, “+2”, “+3”.
•
To change the value simply type the following command:
C:\MtxGL2FineTuning COMxx yy (where yy is the new value assigned)
13
•
Turn ON the Xbox360, and place back the DIP switch in the corresponding FAT
model position. The Matrix Glitcher2 will automatically reset itself and
attempt to glitch with the new settings.
•
In case the results are not suitable simply put again all the four DIP switches in the
OFF position and try another value.
•
Is better to try at least 5 Glitching attempts and make an average of them to judge
the quality of the glitching time.
6.Enjoy
You can now start your console normally and see XeLL boot within 30 seconds.
You can now enjoy unsigned code on your slim.
14