2840A AIRCONDITION RESET

background image

2840

A

TECHNICAL NOTE

YELLOW

Edition Anglaise

The repair methods given by the manufacturer in this document are based on the

technical specifications current when it was prepared.

The methods may be modified as a result of changes by the manufacturer in the

production of the various component units and accessories from which his vehicles

are constructed".

All copyrights reserved by Renault.

Copying or translating, in part or in full, of this document or use of the service part

reference numbering system is forbidden without the prior written authority of

RENAULT.

HEATING - AIR CONDITIONING : PASSENGER COMPARTMENT FAN SPEED

SEPTEMBER 1997

77 11 195 572

Service 0429

Basic manual :

M.R. 315

Other sub-section concerned :

• Engine :

XXX

• Gearbox :

XXX

C

RENAULT 1997

62

CUSTOMER COMPLAINT

- Intermittent operation of the passenger

compartment fan speed.

POSSIBLE CAUSE

- Poor contact caused by the relay on its support .

CLAIM COMPLETION AND CODING

Destination of removed parts :
- As per Warranty Policy and Procedures

Manual.

New NITG Code :

E338

Old NITG Code :

8224

Supplier Code :

258 / 095

Customer Complaint Code : 7S

Operation Code :

8090

Time allowed :

0.2 hours

S/Section

Factory & Fabrication Cut-off

Type

JE0

A

T 000001

t o T 003711

62

T 000001

t o T 005003

62

JE0

E

61

background image

AIR CONDITIONING

Fan motor

AFTER SALES SOLUTION

Operation to be carried out :
- Change the 40A yellow relay for a 50A mauve

relay.

Vehicles concerned :
- See vehicle types and ranges on title page.

When to take action :
- Upon receipt of a customer complaint.

Parts required :
- Mauve 50A relay

Part No. : 77 00 810 396.

Tooling required :
- None.

Description of operation :
- Disconnect the battery.
- Open the engine interconnection box in the

engine compartment.

- Change the fan speed relay (yellow 40A relay)

for a mauve 50A relay for which you will have
to cut the mounting plate.

- For JEO A type vehicles (1).
- For JEO E type vehicles (2).
- Check the condition of the relay support ter-

minals.

- Check the tightening of the bar (3).
- Reconnect the battery.
- Reset the clock.

ATTENTION :

following an operation on the in-

terconnection box, check that the plastic cover is
correctly secured.
- Apply the procedure for self-setting of the

heater controls if necessary (if the three LED
C.I.J. (see Fig.3)
are permanently illuminated).

With the ignition switched off :
- Place control button (A) to the fully cold posi-

tion (button turned left to the end stop).

- Place air flow control (B) to the end stop at 0.
- Press buttons (E) and (J) at the same time and

keep them pressed down, then switch off the
ignition
.

- Tell-tale light (K) will flash and as soon as it

starts to flash, release the two buttons.

- When the set up is completed and is correct,

tell-tale (K) and the tell-tale for button (I) will
be permanently illuminated.

- If the set up is completed and is incorrect, tell-

tale lights on buttons (C, J, I) will be perma-
nently illuminated (see the Fault-finding ma-
nual section of MR 315
).

62

DIM6208-1

Fig. 2

10140M2

Fig. 3

DIM6207-1

Fig. 1

62 - 2


Document Outline


Wyszukiwarka

Podobne podstrony:
launch cresetter oil lamp reset tool introduction
Fan reset Espace
Bmw reset Service e46 e39 e53(1)
easy500 Master reset HLP EN
DIY Auto Computer Reset
Compasseo 500 600 Rendere fruibile WinCE dopo Hard Reset
Alarm Reset
Reset Windows Password OPIS
sciaga MIKRO RESET, Ekonomia, Ekonomia stacjonarna I stopień, I rok, Mikroekonomia
KATALOG AIRCON 2007
Instrukcja Trial Reset by Dj KoKoS
Reset pralki, KODY Pralek i inne
canon reset
Reset
reset DME
Kasowanie Reset Rejestracja Wymiany Akumulatora BMW
canon reset

więcej podobnych podstron