®
1 of 2
R.60595
Specifications
Power Output
RMS Power (at 12V, 20-20kHz)
Per Channel into 4
Ω
..................... 100W x 2 (0.08% THD)
Per Channel into 2
Ω
........................ 200W x2 (0.3% THD)
Bridged 1 Channel into 4
Ω
........... 400W x 1 (0.3% THD)
Dynamic Power (at 14.4V, 20-20kHz)
Per Channel into 4
Ω
.................... 150W x 2 (0.08% THD)
Per Channel into 2
Ω
....................... 300W x 2 (0.3% THD)
Bridged 1 Channel into 4
Ω
........... 600W x 1 (0.3% THD)
Frquency Response ....................... 10Hz to 50kHz (
±
0, -1 dB)
Signal-to-Noise Ratio . 100dBA(referenced to rated power)
Input Sensitivity (for rated power)
Line inputs .......................... 200mV-4V (500mV at detent)
......................................................................... (1.0V at center)
MRV-1000
2/1 Channel V12 Series Power Amplifier
Specifications and design are subject to change without notice.
Features
•
2/1 CHANNEL OPERATION - Can be used in a 2
channel mode providing 100W x 2 into 4 ohms or
200W x 2 into 2 ohms, or in mono mode producing
400W x 1 into 4 ohms. (all power ratings are from 20Hz
to 20kHz at 12V DC).
•
MULTIMODE™ CAPABILITY - The MRV-1000 can
operate in 2-channel stereo and bridged mono modes
simultaneously.
•
ACTIVE DIVIDING NETWORK - A built in variable
electronic crossover network from 50 - 200Hz (12 dB
per octave) can be used to set up the amplifier for low
pass or high pass applications. This network can also
be switched off for full range applications.
•
DUO ß FEEDBACK CIRCUITRY - Supplies low nega-
tive feedback throughout the audio frequency band-
width and very high negative feedback at DC. This
stabilizes the amplifier, removes the DC offset, offers
excellent total harmonic distortion (THD), and pro-
vides low transient intermodulation distortion (TIM).
•
NO CURRENT LIMITING - Absence of current limit-
ers in the audio section ensures low TIM, excellent
transient response and superb sound quality.
•
S.T.A.R. CIRCUITRY - Alpine-developed Signal Tran-
sient for Accurate Response circuit topology improves
sonic properties by reducing interaction between dif-
ferent sections of the circuitry.
•
INPUT MODE SELECTOR SWITCH - Mono; Stereo;
left + Right.
•
CONTINUOUSLY ADJUSTABLE GAIN CONTROL
•
FULLY DISCRETE, COMPLEMENTARY OUTPUT
CIRCUITRY
•
GOLD PLATED RCA INPUT CONNECTORS AND
SCREW-DOWN POWER AND SPEAKER TERMI-
NALS.
•
DOUBLE BUFFERED PRE-AMP INPUT CIRCUITRY
•
DARLINGTON OUTPUT CIRCUITRY
•
MATCHED POWER SUPPLY MOSFETS
•
HIGH PERFORMANCE, LOW NOISE, AUDIOPHILE
QUALITY ACTIVE AND PASSIVE COMPONENTS
•
DUAL MIRRORED PWM POWER SUPPLIES
•
PULSE WIDTH MODULATED (PWM) DC-DC
POWER SUPPLY - Alpine developed a new type of
PWM power supply that maintains rated power out-
put down to 12V DC and allows for an approximately
40% increase in output power at higher, real world,
battery levels.
•
LED STATUS MONITOR
2/1 CHANNEL
POWER AMPLIFIER
POWER
PHASE
1(MONO) ST 1+2
INPUT MODE
OFF
HP
LP
FILTER
NOM
GAIN
MIN
MAX
50
200
100
(Hz)
CROSSOVER
0
°
180
°
MRV - 1000
Slew Factor .......................................................... Greater than 5
Input impedance ......................................................... 10k ohms
Speaker Impedance .................. 4 or 2
Ω
(stereo) or 4
Ω
mono
Dividing Network Frequency and Slope ............... 50-200Hz
................................................................. 12dB/Octave Slope
Power Requirements ............. 11-16V DC (negative ground)
Dimensions (WxHxD) ............................ 9-7/16"x2-1/16"x13"
...................................................................... (240x53x330mm)
Weight .............................................................. 8lb. 13oz.(4.0kg.)
R.60595
®
2 of 2
2/1 Channel V12 Series Power Amplifier
MRV-1000
Red (Right)
White (Left)
Low Level
Output
Remote - Out
or
Power Antenna Lead
Remote-On Lead
(Blue/White - +12V
Input turns Amp on)
Ground Lead (Black)
Battery Lead (Yellow)
Right Speaker Output Lead (+)
Right Speaker Output Lead (-)
Speaker Output Lead (+)
Speaker Output Lead (-)
4 Ohm ONLY Mono Loading
2 Ohm or 4 Ohm Stereo Loading
This Amplifier is Capable of running MultiMode™
Left Speaker Output Lead (+)
Left Speaker Output Lead (-)
BRIDGED
POWER SUPPLY
-
-
-
+
+
+
CH-2 (R)
CH-1 (L)
BATTERY
REMOTE
GND
20
20
30A
30A
FUSE
CH-2
CH-1
(R)
(L)
SPEAKER OUTPUT
Battery
+
-
Fuse Holder
Battery Power
Wire (Optional)
Power Distribution
Block (Optional)
POWER SUPPLY
BATTERY
REMOTE
GND
BRIDGED
CH-2 (R)
–
–
CH-1 (L)
+
–
+
+
CH-2
CH-1
(R)
(L)