{Change Comments ***********************************************************}

{7/17/90
Copied & modified: Cincinnati Acr 850MC M196.62
For: Viratec
MachSpec:
Added "%" for EOR
Deleted ":" from program ID Label
Changed Sequence label from "N" to "N?"
Prog:
Changed ProgID1 to Program#
Moved OpToolID & ToolChng to same line as WFO1 and added ":?" as Sequence label. (alignment block)
Changed Seq to SeqLab and added Retag, needed due to alignment blocks.
Modified subroutine branching logic to use "=" insted of ">" as ReTag removes the ">".
Added CheckSpinOn sub, turn on spindle and coolant.
Deleted CoolOff, it shuts off with the spindle.
Deleted OfstOff.
Added EOR to end of Prog.
Changed in Drilling for RetractToCP1 to use CP1LessCP2# command.
Updated to .72.1 format
JR}

{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}

{4/3/91
Modified: Cin Acr 850MC (VTF) M328.72.1
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}

{2/3/92
Modified: Cin Acr 850MC (VTF) M328.79
For: Viratec
Updated to Version 4.0 per Fanuc 6M M001.81 Format.
Added a ':' to the Program# Line, per request.
Deleted all 'G80' commands from the form and prog.
KM}

{12/17/92,
Modified: Cin Acr 850MC (VTF) M328.81.1
For: Gibbs & Associates
Updated to Version 4.1 per Fanuc 6M M001.81.2 Format.
DWB}

{7/13/93
Modified: Cin Acr 850MC (VTF) M328.81.2
For: Viratec
Deleted the G94 from the Saftey Start Block at the beginning of the program.
Jim Radcliffe}

{11/3/93
Modified: Cin Acr 850MC (VTF) M328.81.3
For: Viratec
Changed FormatArc to output unconditional end points for their respective planes.
Jim Radcliffe}

{2/9/96, Updated .81 version to .84, MPK}

{3/22/96, Tested ZOnlyRepAutCycle, Incremented number to .87, MPK}

{9/12/96
Initial: Cin Acr 850MC (VTF) M328.87
Created: Cin Acr 850MC (VTF) M328.89
For: Viratec
Updated to .89 format
Changed to use Program# instead of Tag#,
changed ot use absolute drill depths,
Deleted ZCP1 and FromCP from Drilling cycles (The r word in the cycle handles this)
Changed RLevel To RLevelCin
Deleted W word form drill cycles
Deleted all SpinOff calls
Modified tapping operations to output the Speed and Spindle On on the Drill cycle line
modified cutter comp to not output G40 on a z move (it will still output on a z move if the last feature is an arc)
MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '#####.###;0'
#5 = '#######0'
#6 = '##.##;0.'
#7 = '0000'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CP1LessCP2#,4)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Repeats#,5)
FORMAT(Tag#,5)
FORMAT(Program#,5)
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}

{Prog Subroutines **********************************************************}

RestoreScale:
IF NOT Metric? {CAM file is in english, tools and tool path}
SetScale('25.4') { change to Metric, this is an Metric post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'(MSG, SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'(MSG, OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'(MSG, ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'(MSG, ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'(MSG, TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'(MSG, ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLabC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLabC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLabC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLabC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqLabC PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLabC EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqLabC Feed ZIn FeedEnt EOL
ELSE
SeqLabC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
'(DFS,L' Program# ')' EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'(MSG, WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqLabC 'G10=[T2]V0' EOL {sets temporary register #2 to 0}
SeqLabC 'Q' Program# '1' EOL {branch label 1}
SeqLabC '(CLS,L' Program# ')' EOL {call subroutine}
SeqLabC 'G10=[T2]V[T2]+1' EOL {increment register #2 by 1}
SeqLabC 'G11E[T2]=' Repeats# 'L' Program# '2' EOL {if register #2 is equal to number of repeats then jump to branch label 2}
SeqLabC 'G11L-' Program# '1' EOL {jump backwards to branch label 1}
SeqLabC 'Q' Program# '2' EOL {branch label 2}
StartSub
RETURN

FinishSub1: {part 1}
SeqLabC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqLabC Preset ShiftRC EOL
SeqLabC '(ENS)' EOL
CloseSub
SeqLabC Preset UnshftRC EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqLabC SetWFO EOL
SeqLabC '(CLS,L' Program# ')' EOL
IncWFO
NextWFO
ELSE
SeqLabC 'G10=[T1]V0' EOL {sets temporary register #1 to 0}
SeqLabC 'Q' Program# '1' EOL {branch label 1}
SeqLabC '(CLS,L' Program# ')' EOL {call subroutine}
SeqLabC 'G10=[T1]V[T1]+1' EOL {increment register #1 by 1}
SeqLabC 'G11E[T1]=' Parts# 'L' Program# '2' EOL {if register #1 is equal to number of parts then jump to branch label 2}
SeqLabC 'G11L-' Program# '1' EOL {jump backwards to branch label 1}
SeqLabC 'Q' Program# '2' EOL {branch label 2}
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqLabC '(ENS)' EOL
CloseSub
SeqLabC WFO1 EOL
ELSE
SeqLabC Preset ShiftPC EOL
SeqLabC '(ENS)' EOL
CloseSub
SeqLabC Preset UnshftPC EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLabC AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
IF XYPlane?
MoveXY MoveZC
ELSE
IF XZPlane?
MoveX MoveYC MoveZ
ELSE
MoveXC MoveY MoveZ
END
END
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

CkCRC:
IF LastFeat? { Exit Length Feature }
CRCOffC
ELSE
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
CRCOnC
END
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
END
END
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqLabC MoveSXYC EOL
SeqLabC '(CLS,L' Program# ')' EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqLabC DoDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF AutoCycle?
SeqLabC
IF LastFeat?
CRCOffC
END
DoAbsOrInc RapidC MoveXYZC EOL
ELSE
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC
END
IF XMove? OR YMove? OR ZMove?
SeqLabC DoAbsOrInc RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle?
IF LastFeat?
SeqLabC DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLabC DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLabC FormatArc ArcFeedC EOL
DecelMove2
END
SeqLabC FormatArc DecelFeed EOL
ELSE
SeqLabC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS'
ELSE
'H' NewWFO#
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
'H' NewWFO#
END
END
END
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLabC IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SeqLabC AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqLabC '(ENS)' EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqLabC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Feed IncValue StrtPosC EOL
SeqLabC AbsOrInc
ELSE
SeqLabC Feed
END
ELSE
SeqLabC Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLabC Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqLabC AbsOrInc ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqLabC Rapid ZCP2PlusInc EOL
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLabC '(CLS,L' Program# ')' EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
IF FIFO? {.81}
SeqLabC Feed ZCP2 FeedEnt EOL {.69}
ELSE
SeqLabC Rapid ZCP2 EOL {.69}
END
END {.69}
SeqLabC '(ENS)' EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLabC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqLabC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqLabC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqLabC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLabC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqLabC '(CLS,L' Program# ')' EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
SeqLabC '(ENS)' EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

CheckSpinOn: {turns on spindle and coolant}
IF CoolOff?
SpinOn
ELSE
IF CWSpindle?
'M13'
ELSE
'M14'
END
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

GetStartOfSameTool:
DoOpComments
DoPostScript
SeqLabC WFOStuff EOL
CheckPass
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
FORMAT(Program#,7)
':' Program# EOL
FORMAT(Program#,5)
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramNameComment?
'(MSG, PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'(MSG, ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'(MSG, FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'(MSG, ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'(MSG, OUTPUT IN ' MoveType$ ' MILLIMETERS )' EOL
END
IF PartsComment?
'(MSG, PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'(MSG, FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
SeqLabC Plane CRCOff 'G70' EOL
DoPostScript
':?' OpToolID WFOStuff ToolChng EOL
DoOpComments
SeqLabC Speed CheckSpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLabC AbsOrInc Rapid StrtPos EOL
IF NOT Drilling?
SeqLabC ZCP1 EOL
END
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLabC StrtPos EOL
END
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF ToolChangeAtHome?
SeqLabC AbsOrInc Rapid Home EOL
END
IF LAST ProgStop?
SeqLabC 'M00' EOL
ELSE
SeqLabC ProgStop EOL
END

{Start new Operation}

DoPostScript
':?' Plane OpToolID WFOStuff ToolChng EOL
DoOpComments
SeqLabC Speed CheckSpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLabC AbsOrInc Rapid StrtPos EOL
IF NOT Drilling?
SeqLabC ZCP1 EOL
END
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLabC StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLabC 'M00' EOL

{Start new Operation}

GetStartOfSameTool
SeqLabC Speed CheckSpinOn EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC ZCP1 EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLabC CoolOff EOL
END
IF NewToolOffset?

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
SeqLabC ZCP1 EOL
ELSE

{Start new Operation}

GetStartOfSameTool
SeqLabC SpeedC EOL
SeqLabC PlaneC AbsOrInc Rapid StrtPos EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLabC CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqLabC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqLabC ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqLabC FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqLabC RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLabC AbsOrInc Rapid StrtPos EOL
END
GetCycle
SeqLabC
IF Dwell? AND NOT FIDRO? AND NOT Tap? { IF Bore? AND Dwell? }
'G89'
ELSE
Cycle
END
IF Peck?
IF PeckChipBreaker?
'J0'
ELSE
'J1'
END
END
StrtPos ZDepth RLevelCin Peck FeedEnt EOL
IF CallMasterOp?
SeqLabC '(CLS,L' CallMasterNum# ')' EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLabC '(CLS,L' Program# ')' EOL
StartSub
ToolPath
SeqLabC '(ENS)' EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqLabC Rapid 'G80' ZCP3 EOL
IF Repeats?
FinishSubG92
END
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqLabC AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
SeqLabC 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqLabC EOP EOL
CloseSub
Post2 {organize Subs into one program}
IF UseComments?
SetScale('1') {restore scale for comments}
IF FileBytesComment?
'(MSG, FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'(MSG, FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'(MSG, FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
END
EOR EOL
Close
ReTag