{
MILL=T
LATHE=F
SIMPLE_ROT_POS=F
ROTARY_MILL=F
ADV_MILL=F
SUBS=F
MILLTURN_Y-AXIS=F
METRIC=F
}

{Change Comments ***********************************************************}

{7/7/95, Updated for Catalyst v2.20 per Fanuc 6M M001.10 Format, DWB}
{7/18/95, Added IF NOT LastFeat? at CkCRC sub, DWB}

{1/17/96, Updated .85 to .86 version, MPK}

{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{7/12/96
Modified: Fanuc 6M M001.12
Created: Fanuc 6M M001.13.1
For: Gibbs & Associates
Versions: ncCad 4.33.02/ncCAM 4.33.01/ncPost 4.33.09/Catalyst v3.05C/Compost 4.21.37/1.0a
Updated to .13 version.
DWB}

{10/2/96, updated to .14 format per Fanuc 6M (FW) B001.14, MPK}

{11/22/96
Versions: Catalyst v3.23C/Compost 4.21.37/v1.0b1
.14 Additions:
Deleted Flag(2) for CRCOffsetC at ckCRC and ckCRCNum subs and at setup and initializations.
Added NOT LastFeat? AND Equal? SPZ# EPZ# condition at ckCRCNum sub.
Moved contents of FormatLine back to ToolPath LineFeat.
Modified WorkFixtureOffset logic.
Added Flag(2) for WFOStuff at setup and initializations.
Added SetFlag(2) for EquallySpacedOffsets at OpenMP sub.
Added WFONum sub.
Rewrote logic at WFOStuff sub.
Added EOL to NewWFO MP WFOStuff sub Warning.
Deleted SeqC and EOL at WFOStuff sub.
Added Flag(2) logic at start of EachOp/NextOp Loop.
Moved WFOStuff after MP-OTAP-FU condition at FirstOperation and NewTool.
Added WFOStuff for MP-OTAP-ECP condition at FirstOperation and NewTool.
Added AbsOrInc Rapid to StrtPos block for MP-OTAP-ECP condition at FirstOperation and NewTool.
Added SeqC and EOL at WFOStuff calls at GetStartOfSameTool, FirstOperation and NewTool.
Added SetMaxFeed(12700) for Metric VNC files.
Moved Speed SpinOn after MP-OTAP-FU condition at FirstOperation and NewTool.
Added Speed SpinOn for MP-OTAP-ECP condition at FirstOperation and NewTool.
DWB}

{12/23/96
Initial: Fanuc 6M M001.14m
Created: Fanuc 0M [Gimbel] Mxxx.14
ForUser: Gimbel
Control: Fanuc 0M
Machine: ????
Develop: ComPost2 PPC v1.0b4, Virtual Gibbs 3.23
Comment: New processor per fax.
Changed to 0M format per Fanuc 0M G54 M107.89
Added formatter #7
Added format for Repeats
Changed format Program# to #7, reformat to #5 for DoSubComment.
Changed format CallMasterNum# to #7
Changed sub calls
Changed beginning of tool order:
tool change
comments
saftey
postscript
WFO
Change CRCOffset label to an H
Added M29 block for Rigid Tapping.
Jim Radcliffe}

{18Nov97
Original: Fanuc 0M [Gimbel] MZ97.14m
Created: Fanuc 0M [Gimbel] MZ97.14.1m
For: Gimbel
Changes made per: Kim Vind Andersen
Changed CRC label from H to D in MachSpec
Added Pretool in FirstOp2 and NewToolOp4
Charles Winston}

{12/01/98,
Initial: Fanuc 0M [Gimbel] MZ97.14.1m
Created: C-Tek [PJM] NMT59.16m
For: PJ Machine Tools

Changes to Prog:
1) Modified into LongHand post per Fanuc 6M NMU99.16
2) newTool/end - Deleted incValueC OfstOff commands.
CDH}

{Prog Numeric Format Definitions ****}

#1 = '#.00'
#2 = '#####.###;0.'
#3 = '*#####.###;0.'
#4 = '####.###;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#'
#8 = '0000'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ADD#,4)
FORMAT(ToolDiameter#,4)
FORMAT(TrackXNO#,4)
FORMAT(TrackYNO#,4)
FORMAT(TrackZNO#,4)
FORMAT(Recall#,5)
FORMAT(PartNum#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)
FORMAT(Program#,8)

{Prog Subroutines ****}

restoreScale:
IF NOT Metric? {CAM file is in English, tools and tool path}
SetScale('25.4') { change to Metric, this is a Metric post}
END
RETURN

wFO:
'G' NewWFO#
RETURN

wFOStuff:
IF NewWFO?
IF MultipleParts? AND WorkFixtureOffsets?
EOL
'*** WARNING *** DO NOT USE NEWWFO() WITH MULTIPLE PARTS AND WORK FIXTURE OFFSETS' EOL
ELSE
wFO
END
ELSE
IF Flag?('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF NOT SameTool?
IF MultipleParts?
IF WorkFixtureOffsets?
SetWFO
ELSE
wFO
END
ELSE
wFO
END
END
END
END
SetFlagF('2') { Do not output WFO second time wFOStuff is called for MP-WFO-OTAP-ECP }
RETURN

resetWFO:
IF WorkFixtureOffsets?
SeqC WFO1 EOL
END
RETURN

doPartCycleComment:
IF MultipleParts? AND UseComments? AND SubComment?
'( PART NO. ' PartNum# ' )' EOL
END
RETURN

doCycleComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN

doOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
restoreScale
END
RETURN

pSInit:
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

pSStuff:
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF
END
RETURN

doPostScript:
pSInit
EachPS
SeqC PostScript EOL
pSStuff
NextPS
RETURN

doEndOpPS:
pSInit
EachEOPS
SeqC EndOpPS EOL
pSStuff
NextPS
RETURN

loadPRIMEZCP2:
LoadFeat Num#('0') Num#('0') PRIME ClearancePlane2#
RETURN

pRIMEZCP2:
PRIME ZCP2
RETURN

loadPRIMEZCP3:
LoadFeat Num#('0') Num#('0') PRIME ClearancePlane3#
RETURN

pRIMEZCP3:
PRIME ZCP3
RETURN

connectC:
IF FeedConnect?
FeedC
ELSE
RapidC
END
RETURN

absValueC:
IF NOT AbsValue?
AbsValue
END
RETURN

incValueC:
IF AbsValue?
IncValue
END
RETURN

absOrIncC:
IF AbsoluteMoves?
absValueC
ELSE
incValueC
END
RETURN

entryMove:
IF Repeats? AND ZShiftOnly? AND FeedConnect?
SeqC FeedC ZInC
IF NOT EmptyLine?
FeedEntC
END
EOL
ELSE
IF FeedEntry?
SeqC FeedC ZInC
IF NOT EmptyLine?
FeedEntC
END
EOL
ELSE
SeqC RapidC ZInC EOL
END
END
RETURN

autoCycExitMove:
SeqC absOrIncC CRCOffC
IF FIFO?
FeedC pRIMEZCP2 FeedEntC
ELSE
RapidC pRIMEZCP2
END
EOL
RETURN

exitMove:
IF AutoCycle?
SeqC CRCOffC ZCP3C EOL
ELSE
IF FIFO?
SeqC CRCOffC FeedC ZCP3C FeedEntC EOL
ELSE
SeqC CRCOffC RapidC ZCP3C EOL
END
END
RETURN

finishSub1:
SeqC CRCOffC
IF NOT FeedConnect?
loadPRIMEZCP3
IF ZMove?
IF AutoCycle?
pRIMEZCP3
ELSE
IF FIFO?
FeedC pRIMEZCP3 FeedEntC
ELSE
RapidC pRIMEZCP3
END
END
END
END
EOL
RETURN

formatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN

ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN

doPeck: { longDrillStuff }
IF GreaterThan? SUB# Recall# Num#('3') Peck# SPZ# { IF OldZ - Peck# > Depth }
Save# Num#('3') SUB# Recall# Num#('3') Peck# { Save New Peck Depth }
SeqC Feed 'Z' Recall# Num#('3') FeedEntC EOL { Move to New Peck Depth }
Rapid
IF PeckFullRetract?
SeqC ZCP2 EOL { Retract Tool Full Out }
END
SeqC 'Z' ADD# Recall# Num#('3') Retract# EOL { Move to Retract Position }
TrackZNO# ADD# Recall# Num#('3') Retract# { Update Status Register }
END
RETURN

drillFeature: { longDrillStuff }
SeqC RapidC MoveSXYC EOL
SeqC ZCP2C EOL
IF Peck?
FORMAT(Recall#,4)
Save# Num#('3') ClearancePlane2#
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck doPeck
FORMAT(Recall#,5)
END
SeqC FeedC MoveSZC FeedEntC EOL
IF Dwell?
SeqC 'G4X' Dwell# EOL
END
IF FIFO? OR Tap?
SeqC FeedC ZCP2C EOL
IF RetractToCP1?
SeqC RapidC ZCP1C EOL
END
ELSE
IF RetractToCP1?
SeqC RapidC ZCP1C EOL
ELSE
SeqC RapidC ZCP2C EOL
END
END
RETURN

toolPath:
EACHFeat
IF PointFeat? { Drilling Only }
SeqC MoveSXYZC EOL
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC RapidC MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC FeedC MoveXYZC FeedRateC ckCRCNum EOL
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
SeqC formatArc ArcFeedC EOL
NEXTQuadrant
END
END
END
END
NEXTFeat
RETURN

autoCycCutSub1: {part 1}
CalcACSRXY {calc tool position, CalcAutoCycleStatusRecordXY}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
IF Repeats? AND ZShiftOnly?
entryMove
END
SeqC incValueC EOL
RETURN

autoCycCutSub2: {part 2}
SeqC absOrIncC CRCOffC
IF FIFO?
FeedC ZCP2C FeedEntC
ELSE
RapidC ZCP2C
END
EOL
SetSRSubXY {restore SR to 1st position value}
ReSetPass2 {restore for positioning moves}
RETURN

cutAutoCycle:
IF Repeats? AND NOT ZShiftOnly?
EachRep
IF NOT FirstCycle?
IF FIFO?
Rapid
END
SeqC RapidC StrtPos EOL
IF NOT FeedConnect?
SeqC ZCP2C EOL
END
END
END
EACHFeat
doCycleComment
IF SPXMove? OR SPYMove?
IF FIFO?
Rapid
END
SeqC RapidC MoveSXYC EOL
END
autoCycCutSub1
IF Repeats? AND ZShiftOnly?
EachRep
IF NOT FirstCycle?
doCycleComment
IF SPXMove? OR SPYMove?
SeqC connectC incValueC MoveSXYC EOL
END
absOrIncC
IF FeedConnect?
entryMove
ELSE
IF FeedEntry?
SeqC RapidC ZCP2C EOL
END
entryMove
END
SeqC incValueC EOL
END
toolPath
IF NOT FeedConnect?
autoCycExitMove
END
NextRep
ELSE
entryMove
toolPath
END
autoCycCutSub2
NEXTFeat
IF Repeats? AND NOT ZShiftOnly?
finishSub1
NextRep
END
SetPass1
RETURN

milling:
IF Repeats?
EachRep
doCycleComment
IF SPXMove? OR SPYMove?
SeqC connectC MoveSXYC EOL
END
IF FeedConnect?
entryMove
ELSE
IF FeedEntry?
SeqC RapidC ZCP2C EOL
END
entryMove
END
toolPath
finishSub1
NextRep
ELSE
entryMove
toolPath
END
RETURN

setDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

drilling:
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# FIRST SPZ# {.81.2}
toolPath
setDrillEndOpZ
SeqC DrillOff Rapid ZCP3 EOL
RETURN

longDrilling:
SeqC DrillCP EOL
GetCycle
SeqC StrtPosC EOL
toolPath
LoadFeat Num#('0') Num#('0') ClearancePlane3#
IF ZMove?
SeqC RapidC ZCP3C EOL
END
RETURN

checkPass: {use the correct StrtPos}
IF AutoCycle?
SetPass2
ELSE
SetPass1
END
RETURN

opGuts:
ResetCRCNum
IF FirstOperation? OR NewTool?
RapidF# { Forces FeedEntC/FeedRateC }
END
IF Milling?
SeqC ZCP2C EOL
IF AutoCycle?
cutAutoCycle
ELSE
milling
END
exitMove
ELSE
IF Drilling?
drilling
END
END
RETURN

progStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('2540')
ELSE
SetMaxFeed('100')
END
Save# Num#('1') Num#('0') { MultipleParts Current Tool FirstOp# }
Save# Num#('2') Num#('0') { MultipleParts ToolOp# Counter }
Save# Num#('3') Num#('0') { LongHand PeckCycle }
SetFlagF('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF PSComment? AND UseComments?
'Utility Data:' EOL
' At Op Start: All literals and commands will appear at the beginning of the operation.' EOL
' At Op End: All literals and commands will appear at the end of the operation.' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN

initOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )'
END
EOL
EachOp
IF FirstOperation?
IF ToolChangeAtHome?
SetHome
END
END
NextOp
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' MILLIMETERS )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
restoreScale
RETURN

firstOp1:
Seq OpToolID ToolChng EOL
doOpComments
doPartCycleComment
SeqC Plane 'G80' CRCOff EOL
doPostScript
RETURN

firstOp2:
SeqC wFOStuff EOL
SeqC Speed SpinOn EOL
checkPass
SeqC AbsOrInc Rapid StrtPos
IF NOT LastTool?
PreTool
END
EOL
RETURN

firstOp3:
SeqC OfstOn EOL
SeqC CoolOn EOL
RETURN

newToolOp1:
SeqC CoolOff EOL
RETURN

newToolOp2:
doEndOpPS
IF ToolChangeAtHome?
SeqC absOrIncC Rapid PRIME Home SpinOff EOL
ELSE
SeqC SpinOff EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
RETURN

newToolOp3: {Start new Operation}
Seq OpToolID ToolChng EOL
doPartCycleComment
doOpComments
Seq Plane 'G80' CRCOffC EOL
doPostScript
RETURN

newToolOp4:
SeqC wFOStuff EOL
SeqC Speed SpinOn EOL
checkPass
SeqC AbsOrInc Rapid StrtPos PreTool EOL
RETURN

newToolOp5:
SeqC OfstOn EOL
SeqC CoolOn EOL
RETURN

sameToolOp1:
doEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC incValueC OfstOff EOL
END
END
RETURN

sameToolOp2: {Start new Operation}
doPartCycleComment
doOpComments
doPostScript
checkPass
RETURN

sameToolOp3: {Start new Operation}
SeqC wFOStuff EOL
IF LAST ProgStop?
SeqC PlaneC AbsOrInc Rapid StrtPos Speed SpinOn EOL
SeqC OfstOn EOL
SeqC CoolOn EOL
ELSE
SeqC PlaneC AbsOrInc Rapid StrtPos SpeedC EOL
IF NewToolOffset?
SeqC OfstOn EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
RETURN

end1:
SeqC CoolOff EOL
RETURN

end2:
doEndOpPS
IF FIRST ToolChangeAtHome? {added FIRST modifier}
SeqC absOrIncC Rapid PRIME FirstHome SpinOff EOL
ELSE
SeqC SpinOff EOL
END
IF ProgStop?
SeqC 'M0' EOL
ELSE
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart?
SeqC ProgStop EOL
END
END
RETURN

end3:
SeqC EOP EOL
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

mPallTools1P: {Multiple Parts, All Tools 1 Part}
IF FirstOperation? OR EquallySpacedOffsets?
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
END
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END
opGuts
RETURN

mP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
resetWFO
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END
opGuts
RETURN

mP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
resetWFO
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END
opGuts
RETURN

noMPs: {no multiple parts}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
IF FirstOperation?
firstOp1
firstOp2
firstOp3
ELSE
IF NewTool?
newToolOp1
newToolOp2
newToolOp3
newToolOp4
newToolOp5
ELSE {implied SameTool?}
sameToolOp1
sameToolOp2
sameToolOp3
END
END
opGuts
RETURN

masterSub:
IF MultipleParts?
IF AllToolsOnePart?
mPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
mP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
mP1ToollAllPXcp
END
END
ELSE
noMPs
END
RETURN

endPartSub:
{End of program ************************************************************}

{finish last operation}
end1
IF MultipleParts? AND OneToolAllParts?
resetWFO
END
end2
RETURN

newPart1: {Finish off last Part}
IF FullUp?
SeqC CoolOff EOL
SeqC incValueC OfstOff EOL
END
{doEndOpPS}
RETURN

newPart2: {Start new Part}
sameToolOp2
RETURN

newPart3: {Start new Part}
SetFlag('2') { Need to output wFOStuff twice for MP-ESO-OTAP-ECP, once for all others }
SeqC wFOStuff EOL
SeqC PlaneC AbsOrInc Rapid StrtPos Speed EOL
IF FullUp?
SeqC OfstOn EOL
SeqC CoolOn EOL
END
RETURN

mPLoop:
Save# Num#('2') Recall# Num#('1')
IF WorkFixtureOffsets?
NewWFO
EachWFO
ELSE
EachPart
END
IF AllToolsOnePart?
EachOp
masterSub
NextOp
endPartSub
ELSE { OneToolAllParts }
EachOp
IF Equal? Operation# Recall# Num#('2') { Valid Tool Op }
IF FirstOperation? OR NewTool?
IF FirstPart?
masterSub
ELSE
newPart1
newPart2
newPart3
opGuts
END
ELSE
masterSub
END
IF LastOp?
IF LastPart?
Save# Num#('1') Num#('0')
END
Save# Num#('2') Recall# Num#('1')
ELSE
IF NEXT SameTool?
Save# Num#('2') NEXT Operation#
ELSE
IF LastPart?
Save# Num#('1') NEXT Operation#
Save# Num#('2') Num#('0')
ELSE
Save# Num#('2') Recall# Num#('1')
END
END
END
END
NextOp
END
IF WorkFixtureOffsets?
IncWFO
NextWFO
ELSE
NextPart
END
RETURN

{Start of executable Prog, Top Level ****}

progStart {setup and initializations}
initOp

IF MultipleParts?
IF WorkFixtureOffsets?
{'NOTE: This Post Processor does not support Work Fixture Offsets for Multiple Parts.' EOL
'It is recommended that you change your selection to Equally Spaced Offsets.' EOL}
END
IF AllToolsOnePart?
mPLoop
resetWFO
ELSE
EachOp
IF FirstOperation?
Save# Num#('1') Operation#
END
NextOp
mPLoop mPLoop mPLoop mPLoop mPLoop
mPLoop mPLoop mPLoop mPLoop mPLoop
mPLoop mPLoop mPLoop mPLoop mPLoop
mPLoop mPLoop mPLoop mPLoop mPLoop
mPLoop mPLoop mPLoop mPLoop mPLoop
endPartSub
END
ELSE
EachOp
masterSub
NextOp
endPartSub
END
end3