{Change Comments ***********************************************************}

{added CRCOffC to rapid up and repeats, same as all other Fadal posts, 9/26/88 WFG}
{Changed max rpm from 10000 to 15000 JR 6/5/89}

{1/26/90, Updated: Fadal M003.58, to .69 format, JR}
{2/90/90, Updated: Fadal M003.69, to .70 format, JR}
{3/23/90, 15000 max RPM, JR}

{4/6/90
Added '01' literal for looping once on CallLab line at ZonlyRepAutoCycle & ZonlyRep subs.
DWB}

{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{8/10/90, Updated: Fadal M003.71 to .74 format, JR}

{8/10/90
Copied & modified: Fadal M003.74
For: Admiral
Add CRCOffsetC & ResetCRCNum.
Change to First Tool Not In Spindle.
OpToolID & ToolChng on same line.
WFO's output for MultipleParts & NewWFO only.
Added 'Z0H0' for offset cancel (full up) with CoolOff on same line.
Remove StrtPos from drill cycle line.
CoolOn on same line as OfstOn.
Combine M codes on 1 line.
Jim Radcliffe}

{4/03/91
Modified: Fadal (AEM) M332.74
For: Gibbs & Associates
Updated to Version 4.0 per Fanuc 6M M001.80 Format.
DWB}

{7/2/92
Copied & modified from Fadal (AEM) M332.79
New designation Fadal Format 1 (Amcraft) M---.--
For Amcraft
Add WFO to move to StrtPos.
Add StrtPos to WFO's at multi parts.
Change 'Z0H0' to 'G0G49Z0' for offset cancel and remove CoolOff except at end.
Add 'X0Y10.E0' to bring table to operator for loading. Works with VMC 4020 only. Y value would differ
for other models. Not ideal way to handle but consistent with customers current method.
Add 'M0' before 'M2' at end of program so that table stops at modified E0 position.
Add StrtPos to drill cycle line.
Move Rapid StrtPos lines ahead of IF Multiparts? lines.
KC}

{8/19/92
Added "SetProgNum" to reset subroutine numbers to one "1" regardless of program number
KC}

{2/11/93
Created from Fadal Format 1 [AC] M509.81.2
For: Fadal
By: [cwh]
Changed 'X0Y10.E0' at end to 'X0Y0Z0E0'.
}
{2/16/93
For: Fadal
By: [cwh]
Changed EOP from M2 to M30.
Changed 'G0G49Z0M5M9' at end to 'M5M9' & 'G0G90Z0H0'.
Removed the trailing comments.
Added a 'G8' on a line by itself before the first G1, G2, G3 following a G0.
Changed the tapping cycles back to a standard Fanuc format.
}
{2/22/93
For: Fadal
By: [cwh]
Changed all 'G0G49Z0' to 'G0H0Z0'.
}
{3/8/93
For: Fadal
By: [cwh]
Modified the tap cycle section to test for OptCyc1. ( rigid tap, set
in the post via a PS command. )
Modified the drilling cycle to check for Pulse coolant for use as
a Positive Approach flag. ( set in the post via a PS command. )
}
{5/5/93
For: Gibbs
By: [cwh]
Changed all CRCOffsetC to "'D' Tool#". Also made use of flag('1') to
determine when to output. This was done to counter act a change made
in the Catalyst post code that now adds 50 to the tool number to derive
the CRC Offset value.
}
{5/13/93
For: Fadal
By: [cwh]
Modified the WFOStuff routine to handle work fixture offsets better
with multiple parts by checking the NeedWFO1 boolean.
}
{6/17/93
For: Fadal
By: [cwh]
Modified the second and consequent tool changes from
G0 H0 Z0 M9
T# M6
to
M5 M9
T# M6
Changed the ending sequence to
G0 G90 M5 M9
G53 Z0
X0 Y0 Z0 E0 H0
M30
Changed the spindle on line for Rigid Tap cycles to
S####
G84.2

Added the spindle speed value to the end of the Rigid Tap cycle
definition line.
Changed the coolant on command from M7 to M8.
}
{6/23/93
For: Fadal
By: [cwh]
Modified the second and consequent tool changes to output a
'M5 M9' regardless of the ToolChangeAtHome? result.
}
{12/23/93
For: Fadal
By: [cwh]
Modified to output CRC on leadin arc moves. Also CRC cancelation is on a line by itself.
Modified to limit the maximum number of repeats per sub call to 99.
}

{5/12/94
Modified: CNCVIS2 M611.PST
For: Gibbs & Associates
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.02/Compost 4.21.21
Updated to Version 4.2 per Fanuc 6M M001.81.2d Format.
Reorganized Prog Formats.
Added FIFO? at FinishSub1, AutoCycCutSub2, ZonlyRepAutoCycle subs and end of IF Milling.
Added TrackZNO# FIRST SPZ# at IF Drilling? section to allow for conditionality of MoveSXYZC command.
Moved UnSkipZ from FinishSub1 to ZOnlyRep where SkipZ is set.
Added RestoreScale Sub per 4-Axis Post Processor.
Added CkCRC sub for CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Added Move Checker at StdLine.
Deleted StrtPosC at AutoCycCutSub1
Moved SetPass1 from ZonlyRepAutoCycle to AutoCycPat
Made necessary corrections.
Added FORMAT#7 '00' for Recall# to output leading zeros for Repeat Loops value.
Modified OperationIDComment at DoOpComments.
Modified ToolTypeComment at DoOpComments.
Moved CheckPass call to before StrtPos at FirstOperation and NewTool.
This is important for correct AutoCycle SetPass2 StrtPos values.
Changed SeqLabC to SeqLab where ToolPath output CRCOffC for LastFeat of ArcFeat.
Changed SeqC to SeqLab at CoolOff and CoolOn booleans at SameTool.
Change Post to CloseSub and Post2 at end of Prog.
DWB}
{9/26/94
Modified: CNCVIS2 M611.81.2 to CNCVIS2 M611.81.3
For: Star Metal
By: [cwh]
Modified the main section to handle the use of multiple parts better with
respect to initial postioning and spindle on and off commands.
}

{11/16/94 Fixed bug with Program Stops Tom Hubina}

{6/9/95
Fixed CRC so it won't output on a helix
TH}

{7/10/95
Updated: CNCVIS2 M611.81.5
For: Gibbs & Associates
Versions: ncCad 4.33.01/ncCAM 4.33.01/ncPost 4.33.06/Catalyst v2.14.40/Compost 4.21.30/1.0a
Changes made per Pete Jackson
Updated to Version 4.2 per Fanuc 6M M001.81.2g Format.
Modified CkCRC sub.
Added logic to suppress output of CRCOnC on ZMove Feature.
Added logic to suppress output of CRCOnC in OneFeat ToolPath.
Moved ResetCRCNum at start of ToolPath to CkCRC sub.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to ZMoveOnly Feature at ToolPath RapidFeat.
Outputs G40 at all Z Retract blocks.
Deleted DoArcCRC sub.
CkCRC sub now also called at FormatArc sub.
Deletes use of Flag(8)
Deleted CRCValue sub.
Not needed because problem has been resolved, see 5/5/93.
Deleted SetFlagF(9) at setup and initializations.
Was not being used anywhere.
Simplified output of Canned Drill Cycle block at IF Drilling.
DWB}

{7/14/95, Updated CNCVIS2 M611.81.7 to .85 format per v2.20 Update Instructions .01, JR}

{
Format: Fadal Format 2 Mxxx.85.1
12/6/95
Changed comments to output ('s instead of *'s
Changed line at end of output to be Y10.Z0E0H0 instead of X0Y0Z0E0H0
TH}

{1/17/96, Updated .85 to .86 version, MPK}

{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '#####.###;0.'
#7 = '00'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(Recall#,7)
FORMAT(CallMasterNum#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
SeqLab '( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
SeqLab '( OPERATION ' Operation#
IF OperationIDComment?
': ' OperationType$
END
' )' EOL
IF OperationComment?
SeqLab '( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
SeqLab '( ' WorkGroupComment$ ' )' EOL
END
SeqLab '( TOOL ' Tool#
IF ToolTypeComment?
': ' ToolDiameter# ' ' ToolType$
END
' )' EOL
IF ToolComment?
SeqLab '( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLab 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLab 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLab 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLab 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqLab PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLab EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqLab Feed ZIn FeedEnt EOL
ELSE
SeqLab RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
SeqLab SubIDF EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
SeqLab '( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
Save# Num#('10') Num#('0') { FORMATting for Number of Subroutine Loops }
EachRep
Save# Num#('10') ADD# Recall# Num#('10') Num#('1')
IF GreaterThan? Recall# Num#('10') Num#('99')
SeqLab CallLab '99' EOL
Save# Num#('10') Num#('1')
END
NextRep
SeqLab CallLab Recall# Num#('10') EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqLab CRCOffC EOL
SeqLab
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqLab Preset ShiftR EOL
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftR EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqLab Rapid StrtPos SetWFO EOL
SeqLab CallLab OnePart EOL
IncWFO
NextWFO
ELSE
Save# Num#('10') Num#('0') { FORMATting for Number of Subroutine Loops }
EachPart
Save# Num#('10') ADD# Recall# Num#('10') Num#('1')
IF GreaterThan? Recall# Num#('10') Num#('99')
SeqLab CallLab '99' EOL
Save# Num#('10') Num#('1')
END
NextPart
SeqLab CallLab Recall# Num#('10') EOL
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqLab EndSub EOL
CloseSub
ELSE
SeqLab Preset ShiftP EOL
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftP EOL
END
RETURN

CkCRC: { 4.2 }
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
IF NOT ZMove? AND NOT LastFeat?
CRCOnC
IF NOT EmptyLine?
ResetCRCNum
END
END
END
IF LastFeat? AND EmptyLine? AND NOT ArcFeat? { Exit Length Feature }
CRCOffC
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLab AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
CkCRC
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
RETURN

ToolPath:
EACHFeat
IF NOT Rapid?
IF FirstFeat?
SeqLab 'G8' EOL
ELSE
IF LAST Rapid?
SeqLab 'G8' EOL
END
END
END
IF PointFeat?
IF AutoCycle?
SeqLab MoveSXYC EOL
SeqLab CallLab OnePart EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqLab DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF AutoCycle?
SeqLab DoAbsOrInc
IF LastFeat?
CRCOffC {.70}
END
RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC {.82}
END
RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqLab DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLab DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab FormatArc ArcFeedC CRCOffsetC EOL
DecelMove2
END
SeqLab FormatArc DecelFeed CRCOffsetC EOL
ELSE
SeqLab FormatArc ArcFeedC CRCOffsetC EOL
END
NEXTQuadrant
IF LastFeat?
SeqLab CRCOffC EOL
END
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
ELSE
'E' NewWFO#
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
'E' NewWFO#
END
END
END
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLab IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SeqLab AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqLab EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqLab AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLab Feed IncValue StrtPosC EOL
SeqLab AbsOrInc
ELSE
SeqLab Feed
END
ELSE
SeqLab Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLab Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqLab AbsOrInc ZCP2PlusInc EOL
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqLab Rapid ZCP2PlusInc EOL
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLab CallLab '01' EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
IF FIFO? {.81}
SeqLab Feed ZCP2 FeedEnt EOL {.69}
ELSE
SeqLab Rapid ZCP2 EOL {.69}
END
END {.69}
SeqLab EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLab Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqLab FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqLab RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqLab CallLab '01' EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqLab EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

GetStartOfSameTool:
DoOpComments
DoPostScript
WFOStuff
CheckPass
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('15000')
SetMaxFeed('500')
Save# Num#('10') Num#('0') { FORMATting for Number of Subroutine Loops }
SetFlagF('1') { Milling ZShiftOnly SepSubs }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
SeqLab 'O' Program#
IF UseComments? AND ProgramNameComment?
'( ' ProgramName$ ' )'
END
EOL
SetProgNum('0')
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
SeqLab '( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
SeqLab '( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
SeqLab '( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
SeqLab '( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
SeqLab '( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
SeqLab '( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
SeqLab OpToolID ToolChng EOL
DoOpComments
DoPostScript
IF Drilling? AND Tap? AND OptCyc1?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLab Plane AbsOrInc Rapid StrtPos WFOStuff EOL
SeqLab OfstOn CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLab StrtPos EOL
END
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
SeqLab Rapid AbsOrInc SpinOff CoolOff EOL
SeqLab 'G53Z0' EOL { OfstOff }
DoEndOpPS
IF ToolChangeAtHome?
SeqLab 'G53' Home EOL
END
IF LAST ProgStop?
SeqLab 'M00' EOL
ELSE
SeqLab ProgStop EOL
END

{Start new Operation}

SeqLab OpToolID ToolChng EOL
DoOpComments
DoPostScript
IF Drilling? AND Tap? AND OptCyc1?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqLab Plane AbsOrInc Rapid StrtPos WFOStuff EOL
SeqLab OfstOn CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqLab StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLab 'G0H0Z0' CoolOff SpinOff 'M00' EOL

{Start new Operation}

GetStartOfSameTool
IF Drilling? AND Tap? AND OptCyc1?
SeqLab SpeedC EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab SpeedC SpinOn EOL
END
SeqLab PlaneC AbsOrInc Rapid StrtPos WFOStuff EOL
SeqLab OfstOn CoolOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLab CoolOff EOL
END
IF NewToolOffset?

{Start new Operation}

GetStartOfSameTool
SeqLab 'G0H0Z0' EOL
SeqLab SpeedC EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos WFOStuff EOL
SeqLab OfstOn EOL
ELSE

{Start new Operation}

GetStartOfSameTool
SeqLab SpeedC EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos WFOStuff EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLab CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqLab ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqLab ZCP3C EOL
ELSE
SeqLab CRCOffC EOL { Just in case }
IF FIFO? {.81}
SeqLab FeedC ZCP3C FeedEntC EOL
ELSE
SeqLab RapidC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLab AbsOrInc Rapid StrtPos WFOStuff EOL
END
IF Pulse? { Positive Approach On }
SeqLab 'M46' EOL
END
SeqLab DrillCP EOL
GetCycle
SeqLab
IF Tap? AND OptCyc1?
'G84.1'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt
IF Tap? AND OptCyc1?
Speed
END
EOL
IF CallMasterOp?
SeqLab 'L' CallMasterNum# '01' EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLab CallLab '01' EOL
StartSub
ToolPath
SeqLab EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
IF Pulse? { Positive Approach Off }
SeqLab 'M47' EOL
ResetCool
END
SeqLab Rapid 'G80' ZCP3 EOL
IF Repeats?
FinishSubG92
END
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
SeqLab Rapid AbsOrInc SpinOff CoolOff EOL { 'G0G90M5M9' }
SeqLab 'G53Z0' EOL { OfstOff }
DoEndOpPS
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
SeqLab AbsOrInc Rapid FirstHome EOL
END
IF ProgStop?
SeqLab 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqLab 'Y10.Z0E0H0' EOL
SeqLab EOP EOL
EndSubs
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
Reseq
{ File Length Comments deleted 2/16/93 }