{Change Comments ***********************************************************}

{8/16/93
Copied & modified: Fanuc 6M M001.81.2
For: Olson Manufacturing & Distribution, Inc.
Control: Centurion V
Machine: Milltronics Partner 1
Created new processor from FastCAM II manual (same info as Centurion V manual!).
Added 'G20', Inch Program, to Saftey Start Block.
Added 'G32', for a Z move to Tool Change position, to Saftey Start Block.
CRCOff on last non-arc feat.
OfstOn, G43 H value, is applied to the axis perpendicular to the current plane.
Call literal G17 before OfstOn and added sub GetPlane, Plane has not output.
OfstOff outputs G49Z0.
Modifications for support and enhancement Drilling section.
Jim Radcliffe}

{8/19/93, .81.3, corrected an ELSE/END bug in ToolPath, JR}
{8/27/93, .81.4, no Home, machine home at end of program, 4 place O codes, JR}

{12/22/94
Updated: Centurion V M589.81.4
For: Gibbs & Associates/Texas Precision Manufacturing
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.04/Compost 4.21.23
Versions: Catalyst v2.14.22C/Catalyst v2.14.22PPC/Compost 4.21.23
Changes made per Pete Jackson.
Updated to Version 4.2 per Fanuc 6M M001.81.2f Format.
Changed TrackZNO# ZDepth# to TrackZNO# FIRST SPZ# at IF Drilling.
SPZ# is affected by SetScale, whereas ZDepth# is not.
Added CkCRC sub for CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Added logic to output CRCOnC in OneFeat ToolPath.
Added logic to suppress output of CRCOnC on ZMove Feature.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to RapidFeat at ToolPath.
Outputs G40 at all ZMoveOnly Feature Retract blocks.
DWB}

{9/27/95, Updated Centurion V M589.81.5 to .85 format per Fanuc 6M M001.85.01.03, JR}

{
Format: Centurion V M589.85.1
10/12/95
Removed All Seqs and SeqCs from post
Changed all sub calls to use GOSUB and RETURN
Each sub now starts with a sequence number equal to the sub number
Changed G49 (OfstOff) to G32
TH}

{11/30/95
Initial: Centurion V M589.85.1
Created: Centurion V M589.85.2
ForUser: Olson
Develop: ComPost 4.21.33, Catalyst68K v2.30.18C
Comment: Modified per marked up readout from John Langenberg
Deleted 2 places.
Changed OfstOff to output G32 only, no Z0.
Added missing right paren to SubComment.
Jim Radcliffe}
{1/17/96 - Updated .85 to .86 format, MPK}

{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{28Jul97
Original: Centurion V M589.89
Created: Centurion V M589.15
For: Gibbs & Associates
Updated to .15 Format per Fanuc 6M M001.15
Charles Winston}

{28Jul97
Original: Centurion V M589.15
Created: Centurion V B589.15
For: Gibbs & Associates
Created B Style post per Fanuc 6M (FW) B001.15
Charles Winston}

{4/1/98
Original: Centurion V B589.15
Created: Centurion V B589.15.1
For: Gibbs & Associates
Fixed bugs in Sub calls:
Changed ['GOSUB ' Program#] at end of OpenMP:, WorkFixtureOffsets?,
WFOCS? False section of StartSub.
Changed ['GOSUB ' Program#] to ['GOSUB ' CSSubID#] in DoCSWFOOps sub.
Joe Cusimano}

{5/19/98,
Initial : Centurion V B589.15.1
Created: Centurion V [TPIS] BV82.15
Customer: TPI Specialty, Dan Enrics 612/448-5330

Changes to "Form":


1. Under Tool Offsets, changed Tool Lenght Offset Cancel number to 49 and Unchecked
Cancel Offset Only at Good Z.

Changes to "Prog":

1. For Rigid Tapping, added G88 & Feed per Rev. Also added Format for FeedTapIPR#.
2. Moved CoolOn (M8) from the Z-axis motion to the X & Y axes motion.
3. At End, removed G53 block.
4. Added Rapid & ZCP3 to the G80 block.
5. Under SameToolOp1, added OR ChangeCS? before OfstOff.
JHE}


{Prog Numeric Format Definitions *****************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####.##'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(TrackZNO#,4)
FORMAT(Retract#,4)
FORMAT(FeedTapIPR#,4) {Added - JHE}
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(CSSubID#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)

{Prog Subroutines **************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

CSPartNum#:
ADD# CS# MUL# NumOfCS# SUB# PartNum# Num#('1')
RETURN

CSWFO:
'G' ADD# CSPartNum# Num#('53')
RETURN

WFO:
'G' ADD# PartNum# Num#('53')
RETURN

WFOStuff:
IF Flag?('2')
IF NOT SameTool?
IF WFOCS?
CSWFO
ELSE
WFO
END
ELSE
IF WFOCS?
IF ChangeCS?
IF MultipleParts?
{MP ChangeCS is handled in SubCSMP and CloseMP}
ELSE
CSWFO
END
END
END
END
END
SetFlagF('2')
RETURN

CSG52:
IF FirstOperation? OR NewTool? OR ChangeCS?
'G52X' CSOffsetX# 'Y' CSOffsetY# 'Z' CSOffsetZ# EOL
END
ClearCSOffset
RETURN

G52Stuff:
IF AAxisAvail? OR BAxisAvail?
IF NOT WFOCS?
IF MultipleParts?
IF WorkFixtureOffsets?
CSG52
END
ELSE
CSG52
END
END
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoCSComment:
IF AAxisAvail? OR BAxisAvail?
'( CS#' CS# ' - ' CSComment$ ' )' EOL
END
RETURN

DoCSWFOComment:
ClearCSOffset
IF AAxisAvail? OR BAxisAvail?
IF FirstOperation? OR NewTool? OR ChangeCS?
'( ' CSWFO ' = X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ#
IF AAxisAvail?
' A' CSOffsetA#
END
IF BAxisAvail?
' B' CSOffsetB#
END
' )' EOL
END
END
RETURN

CSComments:
IF WFOCS?
IF MultipleParts?
IF OneToolAllParts? AND ExitClearancePlane?
ClearCSOffset { Necessary for correct StrtPos in Main }
END
ELSE
DoCSComment
DoCSWFOComment
END
ELSE
DoCSComment
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
CSComments
RETURN

CSAngleA:
IF AAxisAvail?
IF WFOCS?
'A0.'
ELSE
'A' CSOffsetA#
END
END
RETURN

CSAngleAC:
IF AChange?
CSAngleA
END
RETURN

CSAngleB:
IF BAxisAvail?
IF WFOCS?
'B0.'
ELSE
'B' CSOffsetB#
END
END
RETURN

CSAngleBC:
IF BChange?
CSAngleB
END
RETURN

PSInit:
NewWFOF
FourthCWF
FourthCCWF
FifthCWF
FifthCCWF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff:
RETURN

DoPostScript:
PSInit
EachPS
PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
EndOpPS EOL
PSStuff
NextPS
RETURN

EntryMove:
IF FeedEntry?
Feed ZIn FeedEnt EOL
ELSE
RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
'N' Program# EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
'GOSUB ' Program# RepLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
Preset ShiftRC EOL
'RETURN' EOL
CloseSub
Preset UnshftRC EOL
RETURN

ToggleIncDecWFO:
IF Flag?('3')
SetFlagF('3')
ELSE
SetFlag('3')
END
RETURN

DoCSG52Ops:
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
ELSE
SetWFO EOL
END
'GOSUB ' Program# RepLab OnePart EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
IF WFOCS?
StartSub
SaveCSProg
SaveCSOpStart
ClearCSOffset
ELSE
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-OTAP-ECP }
END
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoCSG52Ops
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoCSG52Ops
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
StartSub
END
ELSE
'GOSUB ' Program# RepLab Parts EOL
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('2') { WFOStuff }
END
StartSub
END
RETURN

DoCSWFOOps:
EachCSOp
DoCSComment
DoCSWFOComment
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
ELSE
CSWFO EOL
END
'GOSUB ' CSSubID# EOL
NextCSOp
RETURN

CloseMP:
IF WorkFixtureOffsets?
'RETURN' EOL
CloseSub
IF WFOCS?
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-OTAP-ECP }
END
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoCSWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoCSWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
END
ELSE
Preset ShiftPC EOL
'RETURN' EOL
CloseSub
Preset UnshftPC EOL
END
RETURN

SubCSMP:
IF WFOCS?
IF ChangeCS?
'RETURN' EOL
CloseSub
NewProg
StartSub
SaveCSProg
END
ClearCSOffset
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN

ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN

ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
MoveSXYC EOL
'GOSUB ' Program# EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
DoDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF LastFeat?
DoAbsOrInc CRCOffC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
DoAbsOrInc RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
DoAbsOrInc CRCOnC RapidC MoveXYZC ckCRCNum EOL
END
END
END
ELSE
IF LineFeat?
IF LastFeat?
DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
IF Decelerate?
IF RoomToDecel?
DecelMove1
DoAbsOrInc CRCOnC FeedC MoveXYZC FeedRateC ckCRCNum EOL
DecelMove2
END
DoAbsOrInc CRCOnC FeedC MoveXYZC DecelFeed ckCRCNum EOL
ELSE
IF XMove? OR YMove? OR ZMove?
DoAbsOrInc CRCOnC FeedC MoveXYZC FeedRateC ckCRCNum EOL
END
END
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
FormatArc ArcFeedC EOL
DecelMove2
END
FormatArc DecelFeed EOL
ELSE
FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
ELSE
IF FIFO?
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
'RETURN' EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
Feed
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
IncValue StrtPosC EOL
AbsOrInc
END
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
Rapid
IF SPXMove? OR SPYMove?
IncValue StrtPosC EOL
AbsOrInc
END
IF FeedEntry?
ZCP2PlusInc EOL
END
END
IF FeedEntry?
Feed ZInPlusInc FeedEnt EOL
ELSE
IF FirstCycle?
Rapid
END
RapidC ZInPlusInc EOL
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
'GOSUB ' Program# EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
Feed ZCP2 FeedEnt EOL
ELSE
Rapid ZCP2 EOL
END
END
'RETURN' EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
Connect StrtPos EOL
END
IF FeedConnect?
FeedC ZInPlusInc FeedEnt EOL
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
RapidC ZCP2PlusIncC EOL
END
Feed ZInPlusInc FeedEnt EOL
ELSE
RapidC ZInPlusInc EOL
END
END
'GOSUB ' Program# EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
'RETURN' EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

GetPlane:
IF XYPlane?
{G17 is allready active}
ELSE
IF XZPlane?
'G18'
ELSE
'G19'
END
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

OpGuts:
Plane GetPlane EOL
IF Milling?
ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
ZCP3C EOL
ELSE
IF FIFO?
FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
AbsOrInc Rapid StrtPos EOL
END
DrillCP EOL
GetCycle
IF FIFO? AND Dwell?
'G89'
ELSE
IF RigidTap? {Added this check and G88 - JHE}
'G88'
ELSE
IF Tap? AND NOT CWSpindle?
'G74'
ELSE
Cycle
END
END
END
FromCP StrtPos ZDepth RLevel Dwell Peck
IF PeckChipBreaker?
'U' Retract#
END
IF Peck?
'D' Retract#
END
IF RigidTap? {Added this check and IPR - JHE}
'F' FeedTapIPR#('1') EOL
ELSE
FeedEnt EOL
END
IF CallMasterOp?
'GOSUB ' CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
'GOSUB ' Program# EOL
StartSub
ToolPath
'RETURN' EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
Rapid 'G80' ZCP3 EOL {Added Rapid & ZCP3 - JHE}
{RapidC ZCP3C EOL} {Moved to G80 block - JHE}
IF Repeats?
FinishSubG92
END
RapidC ZCP3C EOL
END
END
RETURN

ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('12700')
ELSE
SetMaxFeed('500')
END
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetFlagF('2') { WFOStuff }
SetFlag('3') { True = incrementing WFO numbers for MP. False = decrementing WFO numebrs for MP }
SetFlag('4') { True = toggle between incrementing/decrementing WFO's }
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END

IF MultipleParts?
IF WorkFixtureOffsets?
IF LTEqual? MUL# Parts# NumOfCS# Num#('6')
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of parts [ ' Parts# ' ] times CSs [ ' NumOfCS# ' ] )' EOL
'( exceeds the machine limit. Switching to G52 style output. )' EOL
END
END
END
ELSE
IF LTEqual? NumOfCS# Num#('6')
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
'( Not enough Work Fixture Offsets to handle this part. )' EOL
'( Number of CSs [ ' NumOfCS# ' ] exceeds the machine limit. )' EOL
'( Switching to G52 style output. )' EOL
END
END
END
RETURN

InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
RETURN

FirstOp1:
'G17' 'G20' 'G32' CRCOff DrillOff EOL
OpToolID ToolChng EOL
DoOpComments
DoPostScript
RETURN

FirstOp2:
WFOStuff EOL
G52Stuff
Speed SpinOn EOL
CheckPass
Rapid AbsOrInc StrtPos CSAngleA CSAngleB CoolOn EOL {Added CoolOn - JHE}
RETURN

FirstOp3:
OfstOn EOL {Removed CoolOn - JHE}
RETURN

NewToolOp1:
CoolOff EOL
OfstOff EOL
RETURN

NewToolOp2:
DoEndOpPS
SpinOff EOL
IF LAST ProgStop?
'M0' EOL
ELSE
ProgStop EOL
END
RETURN

NewToolOp3: {Start new Operation}
'G17' 'G20' 'G32' CRCOff DrillOff EOL
OpToolID ToolChng EOL
DoOpComments
DoPostScript
RETURN

NewToolOp4:
WFOStuff EOL
G52Stuff
Speed SpinOn EOL
CheckPass
Rapid AbsOrInc StrtPos CSAngleA CSAngleB CoolOn EOL {Added CoolOn - JHE}
RETURN

NewToolOp5:
OfstOn EOL {Removed CoolOn - JHE}
RETURN

SameToolOp1:
DoEndOpPS
IF LAST ProgStop? OR CoolOff? AND LAST NOT CoolOff?
CoolOff EOL
END
IF LAST ProgStop? OR NewToolOffset? OR ChangeCS? {Added OR ChangeCS? - JHE}
OfstOff EOL
END
IF LAST ProgStop?
SpinOff EOL
'M0' EOL
END
IF LAST ProgStop? OR NewToolOffset? OR ChangeCS?
'G17' 'G20' CRCOff DrillOff EOL
END
RETURN

SameToolOp2: {Start new Operation}
DoOpComments
DoPostScript
CheckPass
RETURN

SameToolOp3: {Start new Operation}
WFOStuff EOL
G52Stuff
SpeedC
IF LAST ProgStop?
Speed SpinOn {Added Speed - JHE}
END
EOL
Rapid AbsOrInc StrtPos CSAngleA CSAngleB SpeedC EOL
IF LAST ProgStop? OR NewToolOffset? OR ChangeCS?
OfstOn
END
IF LAST ProgStop? OR NOT CoolOff? AND LAST CoolOff?
CoolOn
END
EOL
RETURN

End1:
CoolOff EOL
OfstOff EOL
RETURN

End2:
DoEndOpPS
SpinOff EOL
IF ProgStop?
'M0' EOL
END
{'G53' Rapid 'Y0.' EOL} {Removed this block - JHE}
RETURN

End3:
EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
OpenMP
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
SubCSMP
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
CloseMP
End3
RETURN

MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
FirstOp1
OpenMP
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
CloseMP
NewToolOp2 {to tool change, CS problem}
NewToolOp3
OpenMP
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
CloseMP
End2
End3
RETURN

MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
SetFlag('2')
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
OpenMP
FirstOp2 {need StrtPos in Sub}
ELSE
IF NewTool?
CloseMP
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
NewToolOp5
OpenMP
NewToolOp4 {need StrtPos in Sub}
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
CloseMP {End of program}
End1
End2
End3
RETURN

NoMPs: {no multiple parts}
EachOp {Start of post processing}
SetFlag('2') { WFOStuff }
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
FirstOp3
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
NewToolOp5
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN

{Start of executable Prog, Top Level ****}

ProgStart {setup and initializations}

IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END