{Change Comments ***********************************************************}
{9/26/88, Added CRCOffC to rapid up and repeats, same as all other Fadal posts, WFG}
{6/5/89, Changed Maximum Spindle RPM from 10000 to 15000 in Form's 'Numbers' Dialog, JR}
{1/26/90, Updated: Fadal M003.58, to .69 format, JR}
{2/90/90, Updated: Fadal M003.69, to .70 format, JR}
{3/23/90, Changed SetMaxRPM from 10000 to 15000 in Prog, JR}
{4/6/90
Added '01' literal for looping once on CallLab line at ZonlyRepAutoCycle & ZonlyRep subs.
DWB}
{7/24/90, Added InitProg globally to posts with this remark, DWB}
{7/24/90, Replaced all occurances of SetSRXYZero with SetSRXYtoSP, DWB}
{8/10/90, Updated: Fadal M003.71 to .74 format, JR}
{3/6/91, Updated: Fadal M003.74 to .76.1 format, JR}
{4/3/91, Updated: Fadal M003.76.1, to .80 format, DWB}
{9/11/91, Updated: Fadal M003.79, to .81 format, DWB}
{* 11/3/93 [cwh]
Modeified: Fadal M003.81
To: Fadal M003.81.1
For: Gibbs and Associates
Modified the form so that it could be used with the 32MP and 32MPOL
versions of Catalyst ( Virtual ).
*}
{11/8/93
Modified: Fadal M003.81.1
For: Gibbs & Associates
Modified to get consecutive sequence numbers thru subroutines:
Changed; Seq to SeqLab, SeqLab to SeqLab and N to N? in MachSpec.
Added Retag
Jim Radcliffe}
{1/3/95
Updated: Fadal M003.81.2
For: Gibbs & Associates
Versions: ncCad 4.33/ncCAM 4.33/ncPost 4.33.04/Compost 4.21.23
Changes made per Pete Jackson
Updated to Version 4.2 per Fanuc 6M M001.81.2f Format.
Corrected FORMAT5 from '########;0' to '#######0'.
Added RestoreScale Sub per 4-Axis Post Processor.
Moved UnSkipZ from FinishSub1 to ZOnlyRep where SkipZ is set.
Changed FeedRateC to FeedEntC for FIFO Exit Moves.
Added CkCRC sub for CRCOffC per version 4.2.
CutterRadiusCompensation ExitLength will output G40 on LastFeat AND LineFeat at StdLine sub.
Changed logic to output CRCOnC in OneFeat ToolPath.
Added logic to suppress output of CRCOnC on ZMove Feature.
Added support of CRC during multiple pocket dog-bone operation.
Added condition to output CRCOnC for XMove OR YMove only at CkCRC sub.
Outputs G41/G42 on First LineFeat after Z Plunge.
Modified condition to output CRCOffC for LastFeat AND AutoCycle at ToolPath RapidFeat.
Assures that G40 is not output prior to LastFeat.
Added CRCOffC to RapidFeat at ToolPath.
Outputs G40 at all ZMoveOnly Feature Retract blocks.
Changed TrackZNO# ZDepth# to TrackZNO# FIRST SPZ# at IF Drilling.
SPZ# is affected by SetScale, whereas ZDepth# is not.
DWB}
{7/19/95, Updated Fadal M003.81.3 to .85 version per v2.20 Update Instructions .01, JR}
{8/15/95,
Fadal M003.85.1
Added literal '01' after CallMasterNum#
Added support for RigidTap per M610.85
TH}
{
Format: Fadal M003.85.2
8/28/95
Fixed duplicate call of Cycle command
Changed SeqLab to SeqLab in rigid tap sections
TH}
{
Format: Fadal M003.85.3
10/12/95
Added UnTool ToolChng to CloseMP: to reload tool1 at the end of each part. This is a First Tool In Spindle post
TH}
{11/17/95
Modified: Fadal M003.85.3
For: Gibbs & Associates
Versions: ncCad 4.33.01/ncCAM 4.33.01/ncPost 4.33.08/Catalyst v2.28.04/Compost 4.21.33/1.0a
Changes made per Mike Dziminowicz of Hughes Aircraft Space & Comm.
Limited UnTool ToolChng block to AllToolsOnePart at CloseMP sub.
DWB}
{
Format: Fadal M003.85.5
11/28/95
Fixed CloseMP so the UnTool ToolChng block will not be output for WFO's if OneToolAllParts
TH}
{1/17/96, Updated .85 to .86 version, MPK}
{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}
{6/18/96,
Initial: Fadal M003.89
Created: Fadal Format 1 C003.13
Updated to .13, changed all SeqLabC to SeqLab, MPK}
{Prog Numeric Format Definitions *******************************************}
#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '#####.###;0.'
#7 = '00'
FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetX#,4)
FORMAT(CSOffsetY#,4)
FORMAT(CSOffsetZ#,4)
FORMAT(ToolDiameter#,4)
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(SUB#,6)
FORMAT(CSOffsetA#,6)
FORMAT(CSOffsetB#,6)
FORMAT(Recall#,7)
FORMAT(CSSubID#,7)
FORMAT(CallMasterNum#,7)
{Prog Subroutines ****}
RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN
DoSubComment:
IF UseComments? AND SubComment?
SeqLab '* SUB NUMBER: ' Program# EOL
END
RETURN
DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
SeqLab '* OPERATION ' Operation# ': ' OperationType$ EOL
END
IF OperationComment?
SeqLab '* ' OperationComment$ EOL
END
IF WorkGroupComment?
SeqLab '* ' WorkGroupComment$ EOL
END
IF ToolTypeComment?
SeqLab '* TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ EOL
END
IF ToolComment?
SeqLab '* ' ToolComment$ EOL
END
RestoreScale
END
RETURN
CSWFO:
'E' ADD# CS# SUB# NewWFO# Num#('1')
RETURN
CalcCSWFO: {(iPart-1)*NumOfCS#)}
'E' ADD# MUL# NumOfCS# SUB# PartNum# Num#('1') ADD# CS# SUB# NewWFO# Num#('1')
RETURN
CSAngleA:
IF AAxisAvail?
'A'
IF NOT Flag?('9')
IF FirstOperation?
IF LessThan? CSOffsetA# Num#('0')
'-'
END
ELSE
IF LessThan? CSOffsetA# LAST CSOffsetA#
'-'
END
END
END
Save# Num#('1') TRUNC# DIV# CSOffsetA# Num#('360')
IF LessThan? CSOffsetA# Num#('0')
Save# Num#('1') SUB# Recall# Num#('1') Num#('1')
END
SUB# CSOffsetA# MUL# Recall# Num#('1') Num#('360')
END
RETURN
CSAngleAC:
IF AChange?
CSAngleA
END
RETURN
CSAngleB:
IF BAxisAvail?
'B'
IF NOT Flag?('9')
IF FirstOperation?
IF LessThan? CSOffsetB# Num#('0')
'-'
END
ELSE
IF LessThan? CSOffsetB# LAST CSOffsetB#
'-'
END
END
END
Save# Num#('1') TRUNC# DIV# CSOffsetB# Num#('360')
IF LessThan? CSOffsetB# Num#('0')
Save# Num#('1') SUB# Recall# Num#('1') Num#('1')
END
SUB# CSOffsetB# MUL# Recall# Num#('1') Num#('360')
END
RETURN
CSAngleBC:
IF BChange?
CSAngleB
END
RETURN
DoCSWFOComment:
SeqLab '* CS#' CS# ' - ' CSComment$ EOL
SetFlag('9')
SeqLab '* ' CalcCSWFO '= X' CSOffsetX# ' Y' CSOffsetY# ' Z' CSOffsetZ# EOL
SetFlagF('9')
RETURN
PSInit:
OptCyc1F
MasterOpF
CallMasterOpF
RETURN
PSStuff:
RETURN
DoPostScript:
PSInit
EachPS
SeqLab PostScript EOL
PSStuff
NextPS
RETURN
DoEndOpPS:
PSInit
EachEOPS
SeqLab EndOpPS EOL
PSStuff
NextPS
RETURN
EntryMove:
IF FeedEntry?
SeqLab Feed ZIn FeedEnt EOL
ELSE
SeqLab RapidC ZIn EOL
END
RETURN
StartSub:
OpenSub
SeqLab SubIDF EOL
DoSubComment
RETURN
SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
SeqLab '* WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT' EOL
' ' EOL
END
END
RETURN
StdSub:
SeqLab CallLab RepCycs EOL
StartSub
RETURN
FinishSub1: {part 1}
SeqLab CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN
FinishSubG92: {part 2}
SeqLab Preset ShiftR EOL
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftR EOL
RETURN
OpenMP:
IF WFOCS?
NewProg
StartSub
SaveCSProg
SaveCSOpStart
ClearCSOffset
ELSE
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqLab SetWFO EOL
SeqLab CallLab OnePart EOL
IncWFO
NextWFO
ELSE
SeqLab CallLab Parts EOL
END
StartSub
END
RETURN
CloseMP:
IF WFOCS?
IF AllToolsOnePart?
SeqLab UnTool ToolChng EOL
END
SeqLab EndSub EOL
CloseSub
NewWFO
EachWFO {simple eachPart}
EachCSOp
DoCSWFOComment
ClearCSOffset
SeqLab CalcCSWFO EOL
SeqLab SubCall CallLabB CSSubID# OnePart EOL
NextCSOp
ClearCSOffset
IncWFO
NextWFO {simple NextPart}
ELSE
IF WorkFixtureOffsets?
IF AllToolsOnePart?
SeqLab UnTool ToolChng EOL
END
SeqLab EndSub EOL
CloseSub
SeqLab WFO1 EOL
ELSE
SeqLab Preset ShiftP EOL
IF AllToolsOnePart?
SeqLab UnTool ToolChng EOL
END
SeqLab EndSub EOL
CloseSub
SeqLab Preset UnshiftP EOL
END
END
RETURN
SubCSMP:
IF WFOCS?
IF ChangeCS?
SeqLab EndSub EOL
CloseSub
NewProg
StartSub
SaveCSProg
END
ClearCSOffset
END
RETURN
DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN
RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqLab AbsValue EOL
END
RETURN
FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN
CkCRC: { 4.2 }
IF XMove? OR YMove? { Approach Length Feature and Multiple Pockets }
IF NOT ZMove?
CRCOnC
END
END
IF LastFeat? AND EmptyLine? { Exit Length Feature }
CRCOffC
END
RETURN
StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc CkCRC FeedC MoveXYZC FeedRateC EOL
END
END
RETURN
ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqLab MoveSXYC EOL
SeqLab CallLab OnePart EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqLab DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF AutoCycle?
SeqLab DoAbsOrInc
IF LastFeat?
CRCOffC {.70}
END
RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqLab DoAbsOrInc
IF ZMove? AND NOT XMove? AND NOT YMove?
CRCOffC {.82}
END
RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqLab DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqLab DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqLab FormatArc ArcFeedC EOL
DecelMove2
END
SeqLab FormatArc DecelFeed EOL
ELSE
SeqLab FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN
AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SeqLab IncValue EOL
RETURN
AutoCycCutSub2: {part 2}
ToolPath
SeqLab AbsOrInc
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
END
EOL
SeqLab EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN
AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN
Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN
G92Sub:
SubWarning
StdSub
SeqLab AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN
ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLab Feed IncValue StrtPosC EOL
SeqLab AbsOrInc
ELSE
SeqLab Feed
END
ELSE
SeqLab Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqLab Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqLab AbsOrInc ZCP2PlusInc EOL
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqLab Rapid ZCP2PlusInc EOL
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLab CallLab OnePart EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqLab Feed ZCP2 FeedEnt EOL
ELSE
SeqLab Rapid ZCP2 EOL
END
END
SeqLab EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN
ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLab Connect StrtPos EOL {added Connect}
END
IF FeedConnect?
SeqLab FeedC ZInPlusInc FeedEnt EOL {changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqLab RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqLab Feed ZInPlusInc FeedEnt EOL
ELSE
SeqLab RapidC ZInPlusInc EOL {added Rapid, reads better} {changed to RapidC, reads better}
END
END
SeqLab CallLab OnePart EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqLab EndSub EOL
CloseSub
RETURN
CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN
ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('15000')
SetMaxFeed('500')
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetFlagF('9') { CSAngleA, CSAngleB and DoCSWFOComment }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
IF MultipleParts?
IF WorkFixtureOffsets?
IF LTEqual? MUL# Parts# NumOfCS# Num#('40')
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
SeqLab '* Not enough Work Fixture Offsets to handle this part.' EOL
SeqLab '* Number of parts ( ' Parts# ' ) times CSs ( ' NumOfCS# ' )' EOL
SeqLab '* exceeds the machine limit. Switching to non-WFO output.' EOL
END
END
END
ELSE
IF LTEqual? NumOfCS# Num#('40') {****}
SetWFOCS { use WFO for CS changes }
ELSE
IF UseComments?
SeqLab '* Not enough Work Fixture Offsets to handle this part.' EOL
SeqLab '* Number of CSs ( ' NumOfCS# ' ) exceeds the machine limit.' EOL
SeqLab '* Switching to non-WFO output.' EOL
END
END
END
RETURN
SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN
SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN
OpGuts:
IF Milling?
SeqLab ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqLab ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqLab FeedC CRCOffC ZCP3C FeedEntC EOL
ELSE
SeqLab RapidC CRCOffC ZCP3C EOL
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLab AbsOrInc Rapid StrtPos EOL
END
SeqLab DrillCP EOL
GetCycle
SeqLab
IF Tap? AND OptCyc1?
'G84.1'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract
IF Tap?
FadalTapF FadalTapQ
ELSE
FeedEnt
END
EOL
IF CallMasterOp?
SeqLab 'L' CallMasterNum# '01' EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLab CallLab OnePart EOL
StartSub
ToolPath
SeqLab EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqLab 'G80' EOL
SeqLab RapidC ZCP3C EOL
IF Repeats?
FinishSubG92
END
END
END
RETURN
DefaultWFO:
IF NeedWFO1?
SeqLab 'E' NewWFO# EOL
END
RETURN
DoCSG52:
{This Post does not use G52s}
RETURN
DefaultCSG52:
{This Post does not use G52s}
RETURN
DefaultCSWFO:
IF NOT SameTool?
SeqLab CSWFO EOL
END
RETURN
WFOStuff:
IF MultipleParts?
IF NOT WorkFixtureOffsets?
DefaultWFO
END
ELSE
IF WFOCS?
IF ChangeCS?
DoCSWFOComment
ClearCSOffset
SeqLab CSWFO EOL
ELSE
ClearCSOffset
DefaultCSWFO
END
ELSE
DefaultWFO
END
END
RETURN
InitOp:
EOR EOL
SeqLab 'O' Program#
IF UseComments? AND ProgramNameComment?
'*' ProgramName$
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
SeqLab '* ' ProgramComment$ EOL
END
IF FormatNameComment?
SeqLab '* FORMAT: ' FormatName$ EOL
END
IF TimeComment?
SeqLab '* ' Date$ ' AT ' Time$ EOL
END
IF MovesComment?
SeqLab '* OUTPUT IN ' MoveType$ ' INCHES' EOL
END
IF PartsComment?
SeqLab '* PARTS PROGRAMMED: ' Parts# EOL
END
IF StartToolComment?
SeqLab '* FIRST TOOL IN SPINDLE' EOL
END
END
OpenSub
RestoreScale
SetProgNum('0')
RETURN
FirstOp1:
DoOpComments
DoPostScript
RETURN
FirstOp2:
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
RETURN
FirstOp3:
CheckPass
SeqLab Plane AbsOrInc Rapid StrtPos CSAngleA CSAngleB EOL
RETURN
FirstOp4:
SeqLab OfstOn EOL
SeqLab CoolOn EOL
RETURN
NewToolOp1:
SeqLab CoolOff EOL
RETURN
NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SeqLab AbsOrInc Rapid Home SpinOff EOL
ELSE
SeqLab SpinOff EOL
END
IF LAST ProgStop?
SeqLab 'M0' EOL
ELSE
SeqLab ProgStop EOL
END
RETURN
NewToolOp3: {Start new Operation}
SeqLab OpToolID EOL
SeqLab ToolChng EOL
DoOpComments
DoPostScript
RETURN
NewToolOp4:
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
RETURN
NewToolOp5:
CheckPass
SeqLab Plane AbsOrInc Rapid StrtPos CSAngleA CSAngleB EOL
RETURN
NewToolOp6:
SeqLab OfstOn EOL
SeqLab CoolOn EOL
RETURN
SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqLab CoolOff EOL
SeqLab SpinOff EOL
SeqLab 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqLab CoolOff EOL
END
END
RETURN
SameToolOp2: {Start new Operation}
DoOpComments
DoPostScript
CheckPass
RETURN
SameToolOp3: {Start new Operation}
IF LAST ProgStop?
IF Drilling? AND RigidTap?
SeqLab Speed EOL
SeqLab 'G84.2' EOL
ELSE
SeqLab Speed SpinOn EOL
END
SeqLab PlaneC AbsOrInc Rapid StrtPos CSAngleA CSAngleB EOL
SeqLab OfstOn EOL
SeqLab CoolOn EOL
ELSE
IF NewToolOffset? OR ChangeCS?
SeqLab SpeedC EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos CSAngleA CSAngleB EOL
SeqLab OfstOn EOL
ELSE
SeqLab SpeedC EOL
SeqLab PlaneC AbsOrInc Rapid StrtPos CSAngleA CSAngleB EOL
END
IF NOT CoolOff? AND LAST CoolOff?
SeqLab CoolOn EOL
END
END
RETURN
End1:
SeqLab CoolOff EOL
RETURN
End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {added FIRST modifier}
SeqLab WFO1 EOL
SeqLab AbsOrInc Rapid FirstHome SpinOff EOL
ELSE
SeqLab SpinOff EOL
END
IF NotEqual? CSOffsetA# Num#('0')
IF AAxisAvail?
SeqLab CSAngleA
END
IF BAxisAvail?
SeqLab CSAngleB
END
EOL
SeqLab Preset
IF AAxisAvail?
'A0'
END
IF BAxisAvail?
'B0'
END
EOL
ELSE
IF NotEqual? CSOffsetB# Num#('0')
IF AAxisAvail?
SeqLab CSAngleA
END
IF BAxisAvail?
SeqLab CSAngleB
END
EOL
SeqLab Preset
IF AAxisAvail?
'A0'
END
IF BAxisAvail?
'B0'
END
EOL
END
END
IF ProgStop?
SeqLab 'M0' EOL
END
RETURN
End3:
SeqLab OfstOff UnTool ToolChng EOL
SeqLab WFOOff EOL
SeqLab EOP EOL
EndSubs
CloseSub
Post2 {organize Subs into one program}
EOR EOL
'BYE' EOL
Close
ReTag
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'* FILE LENGTH: ' FileBytes# ' CHARACTERS' EOL
END
IF FileFeetComment?
'* FILE LENGTH: ' FileFeet# ' FEET' EOL
END
IF FileMetersComment?
'* FILE LENGTH: ' FileMeters# ' METERS' EOL
END
Close
END
RETURN
MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
OpenMP
FirstOp1
WFOStuff
FirstOp2
FirstOp3
FirstOp4
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
SubCSMP
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
NewToolOp6
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
CloseMP
End3
RETURN
MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
WFOStuff
FirstOp2
OpenMP
FirstOp3
FirstOp4
ELSE
IF NewTool?
NewToolOp1
CloseMP
NewToolOp2 {to tool change, CS problem}
NewToolOp3
WFOStuff
NewToolOp4
OpenMP
NewToolOp5
NewToolOp6
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
CloseMP
End2
End3
RETURN
MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp4
OpenMP
FirstOp3 {can't XY position before WFO}
ELSE
IF NewTool?
CloseMP
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp6
OpenMP
NewToolOp5 {can't XY position before WFO}
ELSE {implied SameTool?}
SameToolOp1
SubCSMP
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
CloseMP {End of program}
End1
End2
End3
RETURN
NoMPs: {no multiple parts}
EachOp {Start of post processing}
IF FirstOperation?
InitOp
FirstOp1
WFOStuff
FirstOp2
FirstOp3
FirstOp4
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
WFOStuff
NewToolOp4
NewToolOp5
NewToolOp6
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
WFOStuff
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN
{Start of executable Prog, top level ****}
ProgStart {setup and initializations}
IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END
Wyszukiwarka
Podobne podstrony:
Fadal Format 2 [E] C585 13 1Fadal Format 1 B003 13Fadal Format 2 [AE] B072 13 3mFadal Format 2 G54 VTF BW10 13Fadal Format 2 [G54] B586 13Fadal Format 2 (AC) B807 12Fadal Format 2 [MM] MW60 89Fadal Format 2 [PEP] M116 89 1Fadal Format 2 [HM] MV16 89 1mFadal Format 2 [NW] D611 16 2mFadal Format 1 [DM] M179 15 1Fadal Format 2 LH [Co] MW66 12mFadal Format 1 [6D] MT01 89więcej podobnych podstron