Haas [MP] DX77 15


{Change Comments ***********************************************************}

{5/20/93
Copied & modified: Fanuc 10M M008.81.2
For: Haas Automation
Combined OpToolID and ToolChng on one block at FirstOperation and NewTool.
Combined WFOStuff Speed SpinOn AbsOrInc Rapid StrtPos and OfstOn on one block at FirstOperation,
NewTool and SameTool.
Added CkCRC sub to cancel CutterRadiusCompensation on LastFeature of ToolPath.
Added literal 'G74' for Left-Handed Tapping at Drilling.
Moved Canned Drill Cycle Block to Main Program when Repeats = TRUE at Drilling.
Main program will output the Canned Drill Cycle, and the SubPrograms will contain only the
positions from the second feature on.
DWB}

{8/2/93
Modified: Haas M573.81.2
For: Haas Automation
Changes made per visit with Harold Moon at Haas Automation.
Added ProgramName$ to SubID block at StartSub.
Added blank lines between subs.
Deleted RepLab OnePart at OpenMP.
Moved Rapid, Feed and Connect Commands to be output in front of AbsOrInc on same block.
Deleted colons from all Comments.
Deleted Spaces following '(, and preceeding )' from ProgramNameComment at FirstOperation.
Changed Seq to 'N' Tool# EOL at FirstOperation and NewTool, output on block by itself.
Changed Safe Start block from G17G80G40 to G0G90G54G40G80G17 at FirstOperation and NewTool.
Changed StrtPos block from WFOStuff Speed SpinOn AbsOrInc Rapid StrtPos OfstOn to
Rapid AbsOrInc WFOStuff StrtPos Speed SpinOn at FirstOperation and NewTool.
Added PlaneC to StrtPos block at NewTool.
Moved OfstOn to beginning of CoolOn block at FirstOperation and NewTool.
Changed WFOStuff PlaneC AbsOrInc Rapid to Rapid AbsOrInc WFOStuff PlaneC at SameTool StrtPos block.
Added IF RetractToCP1 boolean at SameTool.
This is to force output of ZCP1 or ZCP2 for Drilling.
Changed RapidC ZCP3C to Rapid ZCP3 at Drilling.
Moved 'G80' to Rapid ZCP3 at Drilling.
Added literal 'M19', Spindle Orient, at OfstOff block at end of Prog.
Added MasterOp/CallMasterOp PostScript Command support for Drilling.
Routines have been added to call previously created subroutines.
Added MasterOpF and CallMasterOpF at PSInit.
Added PostScript Comments regarding MasterOp and CallMasterOp Commands.
Added support of MasterOp and CallMasterOp Commands at Drilling.
Added FORMAT for Recall# to output called sub.
DWB}

{
Format: Haas C573.00
Updated to C Style .00 format per C001.00.01
TH}

{
Format: Haas C573.00.01
12/22/94
Added ClearCSOffset to OpenMP: CloseMP: and SubCSMP:
Added if AChange? OR BChange? to home postition call-out in SameToolOp1
Started using Flag('3') to determine toggle between incrementing through MPs and decrementing through MPs
Changed CloseMP to check Flag('3'). If true, the WFOs will increment from first to last. If false, the WFOs will
decrement from last to first.
Example:
TRUE for 4 parts: G54P1, G54P2, G54P3, G54P4
FALSE for 4 parts: G54P4, G54P3, G54P2, G54P1
This is most useful for tombstone machining on rotary tables. With this method, the code will machine part1, rotate, part2,
rotate, part3, rotate, part4, tool change, part4, part3, part2, part1, toolchange, etc. It minimizes the rotation and also
stops the machine from "winding up".
To do this a new sub was created called ToggleIncDecWFO. The flag is set to true in ProgStart and toggled inside CloseMP
after running through the parts
Replaced SetZRepInc and RestoreAbsOrInc with one sub called DoAbsOrInc. Any line with SetZRepInc now
has DoAbsOrInc as the first command after the SeqC.
TH}

{
Format: Haas C573.00.02
1/10/95
Started using Flag ('4') to turn on Inc/Dec WFO's (See above). True means use Inc/Dec WFO's.
TH}

{
Format: Haas C573.00.03
1/13/95
Formatted TrackZNO# to #4
}

{ Added ClearCSOffset to SubCSMP TH}

{8/23/95 - Updated to .10 format TH}

{
12/15/95
Added CSAngleA CSAngleB to MP1ToollAllPXcp
Fixed OfstOff to output absvalue after incvalue
TH}

{1/17/96, Updated .10 to .11 version, MPK}

{3/25/96, Tested ZOnlyRepAutoCycle, Changed version # to .12, MPK}

{6/27/97
Initial: Haas C573.12
Created: Haas D573.15
Develop: ComPost2 68K 1.0b11, Virtual Gibbs 3.35 PPC
Comment: New D style Haas per Fanuc 6M (NW) D001.15
Jim Radcliffe}

{6/27/97
Initial: Haas D573.15
Created: Haas [MP] D000.15
ForUser: Moseys' Production
Control: Haas
Machine: Haas VMC
Develop: ComPost2 68K 1.0b11, Virtual Gibbs 3.35 PPC
Comment: New processor per edited output and conversation with Brain Fry.
Changed comment on ProgID1 line from ProgramName$ to Program#.
Added ProgramName$ comment to header comments.
Added start up lines to beginning of program.
Changed to First Tool In Spindle format with PreTool.
Moved OfstOn stuff to StrtPos line at beginning of tools.
Added blank line between tools and subs.
Jim Radcliffe}

{Prog Numeric Format Definitions ****}

#1 = '#.00'
#2 = '#####.##;0.'
#3 = '*#####.##;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(CSOffsetA#,3)
FORMAT(CSOffsetB#,3)
FORMAT(ToolDiameter#,4)
FORMAT(TrackZNO#,4)
FORMAT(ADD#,5)
FORMAT(CS#,5)
FORMAT(Program#,5)
FORMAT(CallMasterNum#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)

{Prog Subroutines ****}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

AbsValueC:
IF NOT AbsValue?
AbsValue
END
RETURN

IncValueC:
IF AbsValue?
IncValue
END
RETURN

AbsOrIncC:
IF AbsoluteMoves?
AbsValueC
ELSE
IncValueC
END
RETURN

MPESWFO: { MultipleParts EquallySpaced }
'G' ADD# PartNum# SUB# NewWFO# Num#('1')
RETURN

WFO:
'G' ADD# PartNum# Num#('53')
RETURN

WFONum:
'G' NewWFO#
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts? AND WorkFixtureOffsets?
EOL
'*** WARNING *** DO NOT USE NEWWFO() WITH MULTIPLE PARTS AND WORK FIXTURE OFFSETS' EOL
ELSE
WFONum
END
ELSE
IF Flag?('2')
IF NOT SameTool?
IF MultipleParts?
IF WorkFixtureOffsets?
WFO
ELSE
MPESWFO
END
ELSE
WFONum
END
END
END
END
SetFlagF('2')
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER ' Program# ' )' EOL
END
RETURN

DoCSComment:
IF AAxisAvail? OR BAxisAvail?
'( CS#' CS# ' - ' CSComment$ ' )' EOL
END
RETURN

CSComments:
IF FirstOperation? OR NewTool? OR ChangeCS?
DoCSComment
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ' ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ' ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
CSComments
RETURN

CSAngleA:
IF AAxisAvail?
'A' CSOffsetA#
END
RETURN

CSAngleAC:
IF AChange?
CSAngleA
END
RETURN

CSAngleB:
IF BAxisAvail?
'B' CSOffsetB#
END
RETURN

CSAngleBC:
IF BChange?
CSAngleB
END
RETURN

PSInit:
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff:
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF
END
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
ASCII('13') SubID
IF UseComments? AND ProgramNameComment?
'(' ProgramName$ ')'
END
EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqC CRCOffC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO?
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
RETURN

FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

ToggleIncDecWFO:
IF Flag?('3')
SetFlagF('3')
ELSE
SetFlag('3')
END
RETURN

DoWFOOps:
IF Flag?('5')
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
ELSE
SeqC SetWFO EOL
END
SeqC SubCall CallLab EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('5') { Suppress Redundant WFO for MP-OTAP-ECP }
END
IF Flag?('3')
NewWFO
EachWFO {simple eachPart}
DoWFOOps
IncWFO
NextWFO {simple NextPart}
DecWFO
ELSE
LastWFO
EachWFO {simple eachPart}
DoWFOOps
DecWFO
NextPrevWFO {simple NextPart}
IncWFO
END
IF Flag?('4')
ToggleIncDecWFO
END
ELSE
SeqC SubCall CallLab RepLab Parts EOL
IF OneToolAllParts? AND ExitClearancePlane?
SetFlag('2') { WFOStuff }
END
END
StartSub
RETURN

CloseMP:
SeqC AbsOrIncC EOL
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqC AbsValue EOL
END
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
DoAbsOrInc MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ckCRC:
IF LastFeat?
CRCOffC
ELSE
IF NOT ZMove?
CRCOnC
END
END
RETURN

ckCRCNum:
IF NOT LastFeat? AND Equal? SPZ# EPZ#
CRCOffsetC
END
RETURN

ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC DoDrillAbsOrInc MoveSXYZC EOL
END
ELSE
IF RapidFeat?
IF XMove? OR YMove? OR ZMove?
SeqC ckCRC RapidC DoAbsOrInc MoveXYZC ckCRCNum EOL
END
ELSE
IF LineFeat?
IF XMove? OR YMove? OR ZMove?
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC ckCRC FeedC DoAbsOrInc MoveXYZC FeedRateC ckCRCNum EOL
DecelMove2
END
SeqC ckCRC FeedC DoAbsOrInc MoveXYZC DecelFeed ckCRCNum EOL
ELSE
SeqC ckCRC FeedC DoAbsOrInc MoveXYZC FeedRateC ckCRCNum EOL
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
Seq IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
IF Repeats? AND FeedConnect? AND ZshiftOnly?
SeqC AbsOrInc EOL
ELSE
IF FIFO?
SeqC FeedC AbsOrInc ZCP2 FeedEntC EOL
ELSE
SeqC RapidC AbsOrInc ZCP2 EOL
END
END
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqC Connect AbsOrInc StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
Feed
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC IncValue StrtPosC EOL
AbsOrInc
END
END
SeqC ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
Rapid
IF SPXMove? OR SPYMove?
SeqC IncValue StrtPosC EOL
AbsOrInc
END
IF FeedEntry?
SeqC ZCP2PlusInc EOL
END
END
IF FeedEntry?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FirstCycle?
Rapid
END
SeqC RapidC ZInPlusInc EOL
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC SubCall CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub}
IF FIFO?
SeqC Feed ZCP2 FeedEnt EOL
ELSE
SeqC Rapid ZCP2 EOL
END
END
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL
END
END
SeqC SubCall CallLab EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqC EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

OpGuts:
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C
ELSE
IF FIFO?
SeqC CRCOffC FeedC ZCP3C FeedEntC
ELSE
SeqC CRCOffC RapidC ZCP3C
END
END
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC Rapid AbsOrInc StrtPos EOL
END
GetCycle
SeqC
IF Tap? AND NOT CWSpindle?
'G74'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
IF CallMasterOp?
SeqC SubCall CallLabB CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqC SubCall CallLab EOL
StartSub
ToolPath
SeqC EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
IF Repeats?
FinishSubG92
END
SeqC Rapid DrillOff ZCP3
END
END
RETURN

ProgStart:
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
IF Metric?
SetMaxFeed('12700')
ELSE
SetMaxFeed('500')
END
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetFlagF('2') { WFOStuff }
SetFlag('3') { True = incrementing WFO numbers for MP. False = decrementing WFO numebrs for MP }
SetFlag('4') { True = toggle between incrementing/decrementing WFO's }
SetFlagF('5') { Suppress Redundant WFO for MP-OTAP-ECP }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
RETURN

InitOp:
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'(' Program# ')'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramNameComment?
'(' ProgramName$ ')' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
SetLineStrtChr('/')
SeqC CRCOff 'G49' DrillOff EOL
SeqC IncValue 'G28X0Y0A0' EOL
SeqC Rapid AbsValue 'G54X0Y0A0M0' ASCII('13') EOL
SetLineStrtChr('')
RETURN

FirstOp1:
DoOpComments
DoPostScript
Seq Rapid AbsOrInc Plane CRCOff DrillOff EOL
RETURN

FirstOp2:
SeqC WFOStuff CoolOn EOL
CheckPass
SeqC Rapid AbsOrInc 'G43' StrtPos ZCP1 CSAngleA CSAngleB ToolOfst Speed SpinOn PreTool EOL
RETURN

FirstOp2Xcp:
SeqC Rapid WFOStuff AbsOrInc StrtPos CSAngleA CSAngleB EOL
RETURN

NewToolOp1:
CoolOff EOL
SeqC IncValueC OfstOff 'M19' EOL
RETURN

NewToolOp2:
DoEndOpPS
IF ToolChangeAtHome?
SeqC Rapid AbsOrIncC Home EOL
END
SeqC AbsOrIncC ToolChng EOL
IF LAST ProgStop?
SeqC 'M0' ASCII('13') EOL
ELSE
SeqC ProgStop ASCII('13') EOL
END
RETURN

NewToolOp3: {Start new Operation}
DoOpComments
DoPostScript
Seq Rapid AbsOrInc Plane CRCOff DrillOff EOL
RETURN

NewToolOp4:
SeqC WFOStuff CoolOn EOL
CheckPass
SeqC Rapid AbsOrInc 'G43' StrtPos ZCP1 CSAngleA CSAngleB ToolOfst Speed SpinOn PreTool EOL
RETURN

NewToolOp4Xcp:
SeqC Rapid WFOStuff AbsOrInc StrtPos CSAngleA CSAngleB EOL
RETURN

SameToolOp1:
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC IncValueC OfstOff SpinOff EOL
SeqC 'M0' EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset? OR ChangeCS?
SeqC IncValueC OfstOff EOL
END
END
RETURN

SameToolOp2: {Start new Operation}
DoOpComments
DoPostScript
CheckPass
RETURN

SameToolOp3: {Start new Operation}
IF LAST ProgStop?
SeqC WFOStuff CoolOn EOL
SeqC Rapid AbsOrIncC 'G43' PlaneC StrtPos ZCP1 CSAngleA CSAngleB ToolOfst SpeedC SpinOn EOL
ELSE
SeqC WFOStuff
IF NOT CoolOff? AND LAST CoolOff?
CoolOn
END
EOL
IF NewToolOffset? OR ChangeCS?
SeqC Rapid AbsOrIncC 'G43' PlaneC StrtPos ZCP1 CSAngleA CSAngleB ToolOfst SpeedC EOL
ELSE
SeqC Rapid AbsOrIncC PlaneC StrtPos CSAngleA CSAngleB SpeedC EOL
END
END
RETURN

End1:
CoolOff EOL
SeqC IncValueC OfstOff 'M19' EOL
RETURN

End2:
DoEndOpPS
IF FIRST ToolChangeAtHome? {added FIRST modifier}
SeqC Rapid AbsOrIncC FirstHome EOL
END
SeqC AbsOrIncC ToolChng EOL
IF Equal? CSOffsetA# Num#('0') AND Equal? CSOffsetB# Num#('0')
ELSE
SeqC
IF AAxisAvail?
CSAngleA
END
IF BAxisAvail?
CSAngleB
END
EOL
SeqC Preset
IF AAxisAvail?
'A0'
END
IF BAxisAvail?
'B0'
END
EOL
END
IF ProgStop?
SeqC 'M0' EOL
END
RETURN

End3:
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH ' FileMeters# ' METERS )' EOL
END
Close
END
RETURN

MPallTools1P: {Multiple Parts, All Tools 1 Part}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
OpenMP
FirstOp1
FirstOp2
ELSE
IF NewTool?
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
CloseMP
End3
RETURN

MP1ToollAllPfu: {Multiple Parts, 1 Tool all Parts, full up}
EachOp {Start of post processing}
IF EquallySpacedOffsets?
SetFlag('2')
END
IF FirstOperation?
InitOp
FirstOp1
OpenMP
FirstOp2
ELSE
IF NewTool?
NewToolOp1
CloseMP
NewToolOp2 {to tool change, CS problem}
NewToolOp3
OpenMP
NewToolOp4
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
CloseMP
End2
End3
RETURN

MP1ToollAllPXcp: {Multiple Parts, 1 Tool all Parts, exit Clearance plane}
EachOp {Start of post processing}
SetFlag('2')
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
OpenMP
FirstOp2Xcp {need StrtPos in Sub}
ELSE
IF NewTool?
CloseMP
NewToolOp1
NewToolOp2 {to tool change, CS problem}
NewToolOp3
NewToolOp4
OpenMP
NewToolOp4Xcp {need StrtPos in Sub}
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
CloseMP {End of program}
End1
End2
End3
RETURN

NoMPs: {no multiple parts}
EachOp {Start of post processing}
SetFlag('2') { WFOStuff }
IF FirstOperation?
InitOp
FirstOp1
FirstOp2
ELSE
IF NewTool?
NewToolOp1
NewToolOp2
NewToolOp3
NewToolOp4
ELSE {implied SameTool?}
SameToolOp1
SameToolOp2
SameToolOp3
END
END {common point for all operations}
OpGuts
NextOp {loops back to EachOP until last Operation}
End1 {End of program}
End2
End3
RETURN

{Start of executable Prog, Top Level ****}

ProgStart {setup and initializations}

IF MultipleParts?
IF AllToolsOnePart?
MPallTools1P
ELSE {implied OneToolAllParts?}
IF FullUp?
MP1ToollAllPfu
ELSE {implied ExitClearancePlane?}
MP1ToollAllPXcp
END
END
ELSE
NoMPs
END


Wyszukiwarka

Podobne podstrony:
Haas [ADB] CU70 15
Haas [6D] MT11 15
Haas [HPD] CY68 15 2
Haas [GH] MW96 15 2
Haas [QC] D587 15 1
Haas [QC] B587 15 1
Haas [GV] BQ25 15
Haas [SI] BX39 15
Haas [WMF] MZ27 15 3
Haas [HA] MZ67 15
Haas [VT] DQ69 15
Haas [HPD] BY68 15 2
Haas [HPD] DY68 15 2
Haas [BMS] DU54 15
Haas [Gimbel] MV90 15 1m
Haas [WMF] CZ27 15
Haas D573 15

więcej podobnych podstron