• Lexmark Laser Error Codes

• Apr. 2nd, 2008 at 8:48 AM

Hi.. All of you.. here is some of the Lexmark Laser Error Code which i get along some where and Listing all of them together.. So that you find Happy Printer Repair

ERROR 20 / ERROR 200
Input Paper Sensor was not triggered - Paper may be jammed at the sensor. Remove toner cartridge for better access to jammed paper.
69G5480 Pickup Roller  99A0070 Pickup Rollers

Paper not being picked up check paper tray & pickup rollers
Replace rollers if worn smooth or cracked

ERROR 21
The exit sensor was not made in time after the input sensor as made.

ERROR 22
The exit sensor was not unmade in time.

ERROR 23
Jam at the duplex unit. Paper is either not leaving the duplex entry sensor in time or not making or unmaking the duplex exit sensor in time. See “Duplex” on page 2-16

Error 24
The defined paper size is too short to print data as formatted.

Error 25
Input sensor made at wrong time. May be due to the paper feeding manually while motors running and previous page in path.

Error 26
Duplex unit is installed but paper tray is not sensed.

Error 27
Envelopes/paper loaded are wrong size.      Load correct size

Error 28

Input sensor not made after pick attempt. Tray is empty or not installed, paper jam in entry throat, or printer is requesting a manual feed.

Error 29
The output bin sensor has not been unmade.See “Output Bin Sensor” on page 2-22.

Error 30
30 Top Cover Open or Print Cartridge Missing Make sure the spring-mounted pin on the printhead shroud is installed
properly and that it is detected by the ramp on the print cartridge as the cover closes. The pin should enter the tower on the HVPS and depress the cover switch.

Error 31
Error code 31 is displayed when the top front cover is closed and a defective print cartridge is detected. It may take the printer 10-20 seconds to determine if the print cartridge is defective.
Remove and reinstall print cartridge.
Shop for Lexmark print cartridges

Error 32
32 Wrong Print Cartridge installed The installed print cartridge is not supported by the Optra printer.

Error 37
37 Insufficient Collation Memory Memory is too full to collate the print job.

Error 38
38 Memory Full Memory used to store pages is full. To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Make sure the memory shown on the printout matches the installed memory.

Error 39
Page too complex to print.To verify that the printer recognizes all the installed memory, go to the user menus and print the “Print Menus” test page. Make sure the memory shown on the printout matches the installed memory.

Error 43
Font card format not supported by printer.
Error 44     Defective font card installed in font slot.
Error 47     47 Font Card Removed While Printing Printer needs data on removed card.
Error 52     Flash Full - Not enough flash memory for data requested to be stored.

Error 53
Unformatted or Defective Flash - Flash problem at POR or while
attempting to write.

Error 54     Serial Error - Framing or parity error on serial.

Error 58
Duplex Not Attached Duplex is electrically connected but no longer mechanically attached, and printer top cover is closed.

Error 59     Duplex Cover Open Top cover of duplex unit is sensed open.
Error 62
Disk Full Not enough disk space for data that has been requested to be written to disk.

Error 63
Unformatted or Defective Disk The printer will ignore a disk it senses as defective. Run the Quick Disk Test. If the test fails, the disk is defective or the data on track1 is bad. If the Quick Disk Test passes but the disk does not work, run the Disk Test/Clean (2 hr. test). Replace the disk if instructed by the operator panel.

Error 7X
Network Card Codes These user codes are documented in various network card user manuals.

Error 80
Network Card Codes These user codes are documented in various network card user manuals.
Error 80     Printer has reached 200,000 prints without maintenance count reset. It is necessary to replace the fuser assembly, transfer roller, and charge roll at this interval to maintain the print quality and reliability of the printer.

Error 82
Photo Developer Cartridge Exhausted
The Photo Develper (OPC belt cartridge) has reached the end of it's life and must be replaced. Press “GO” to clear message and temporarily continue
Install OPC Belt/Photo Developer

Error 84 Transfer
Drum Exhausted     The Transfer drum has reached the end of it's life and must be replaced.  May require service technician
Press “GO” to clear message and temporarily continue
Install Printer
Transfer
Drum Unit

Error 88     Toner Low Toner sensor detects low toner.
Error 230
Paper Jam - Check Duplex
The paper is most likely jammed in the Duplex Unit. Remove the duplex front cover to access the jam area. If the paper is jammed in the rear of the duplex, replace the duplex front cover and open the duplex rear door. If the paper is not
jammed in the duplex unit, then it may be jammed in the rear of the printer. Open the printer rear door to access the jam.

Error 250
Paper Jam - Check MP Feeder Paper is jammed in the multipurpose feeder.
Remove jammed media

Error 90X
Software Error Unrecoverable software error. If one of these errors appeared during POST, or while the printer was idle (not printing or receiving data), or while trying to print one of the internal test pages, replace the system board. If the error appeared while sending a job from the host to the printer, turn the printer off, then turn it on and try again.

Error 901
Engine Flash
Indicates the Flash with the system code program is defective
Peplace System Board
Request Quote

Error 914
DC Pick Motor - No Encoder Feedback
Check the integrated paper tray, tray 1, for paper loading problems. Reload the paper and do a power on reset. Check connecting cables for continuity. If cables, connectors and connections are good replace assemblies listed.
Replace the Autocompensator Assy.
Replace System Board
Request Quote

Error 917
Transfer Roll Error Cannot start servo operation. Verify correct cable connections from the Engine board to the HVPS. Make sure there is continuity between the transfer roller and its contact on the HVPS; replace the transfer roll if the continuity is correct. If there is no continuity, make sure the HVPS contact returns to its upward limit when depressed, and make sure the left bearing of the transfer roll is making proper contact.

Error 920
920 Fuser Error Fuser is below temperature while printing. A 920 error caused by low line voltage can sometimes be cleared by turning the machine off and then on again.

Error 921     Fuser is below standby temperature when idle.

Error 922
Fuser failed to reach standby temperature. Check the continuity of the fuser lamp at the two heavy leads. If an open circuit, replace the lamp or fuser. Thermistor Check:
HOT - J2-1 - J2-2 = 2.5K ohms
COLD = 150K ohms to 260K ohms            Lexmark Fuser
Replace fuser assembly

Error 923
Fuser is too hot while printing or when idle.
Lexmark Fusers

Error 924
924 Fuser Error - Open circuit detected in thermistor circuit.

Error 925
Wrong fuser lamp installed. Check the fuser lamp for the
correct type of lamp that should be installed.• Verify the line voltage is not exceeding the maximum rating
for the printer.
Lexmark Lamps

Error 927
Main Fan Stalled or Cartridge Fan stalled,     Check fan for binding or defective bearing - Replace Fan

Error 928
Erase lamp assembly missing or disconnected

Error 929
The toner sensor is not operating properly, the developer
drive assembly is not operating properly or the print
cartridge is defective.
Error 931     Printhead error - No first sync
Error 932     Lost hsync
Replace Printhead

Error 934     Printhhead Error - Lost Lock condition
Replace Printhead

Error 935     Printhead Error - Mirror motor unable to reach operational speed     Check cables, look for chafing or damage to ribbon cable at sharp bends around rear cover. Replace printhead or ribbon cable.

Error 936/937 Main Drive Motor, Transport Motor
An error with the main drive motor has been sensed by the printer

Optra s 2450 Optra s 1250 Optra s 1650
Optra s 2455 Optra s 1255 Optra s 1855
Optra s 2420 Optra s 1620 Optra S 1625
Optra Se 3455 Optra t610 Optra t612
Optra t614 Optra t616
t520 t522 t620 t622 t630 t632 t634
Power printer off one to two minutes.
Open doors and covers and remove the toner cartridge. Make sure there is no paper jammed in the printer. Pay close attention to the area where the toner cartridge sits. The main motor is located just to the left of the toner cartridge.

If either the 936 error or the 937 error returns after you power on the printer or when you try to print, the printer will require service. The main motor assembly may need to be replaced.

Error 939
RIP Communications Lost
Controller EngineCommunications Lost
The controller board and the engine board cannot
communicate with one another.

POR several times
Check each board
for secure ground.
Replace the assys
in the following
order
1. Controller Bd
2. Engine Board
3. Intterconnect
Board

Error 940-943
Color Machines
Toner Metering Cycle failure CMKY cartridge
940 = Cyan cartridge
941 = Magenta cartridge
942 = Yellow cartridge
943 = Black cartridge
Toner metering cycle (TMC) is where the code and electronics in the printer sense an addition of toner in the cartridge developing area. If the printer is expecting a toner addition cycle but one is not detected, a 94x TMC Error is displayed.
Check the toner metering cam on back of suspect cartridge. If not present check in printer. Replace defective cartridge.
Check the TMC pin in the cartridge contact error for free non binding movement

If pin does not move freely you may need to replace the contact assembly. Contact service person

Error 940
LV Power Supply
Low voltage power supply cross over test failed. Check connections to the to interconnect card assembly. Check AC power source for noise.
Replace low voltage power supply assembly.
Request Quote

953-954
NVRAM
Failure
NVRAM Failure  953: NVRAM Chip Failure
954: NVRAM CRC Failure

Replace System Board

---