{5/24/93
created initial NoSubs Processor to .81 format
FIFO stuff not supported
variables: 1 = tools 1st op; 2 = tools last op; 3 = ncCAMs last op
Jim Radcliffe}

{7/29/93, v.81.1, added FIFO handling, JR}
{8/3/93, v.81.2, SameTool WFO, RapidF#, additional FIFO handling, JR}
{9/12/95, v.81.3, FIFO? queries changed to ExitType & ExitFeed calls, WFO MultipleParts, JR}
{5/8/96, v.89, Return to the StrtPos before next iteration of CutAutoCycle Repeats ZshiftOnly, JR}
{6/4/96, v.89.1, minor corrections SeqC, CRCOff & SameTool, JR}

{12/16/96
Initial: Fanuc 6M NoSubs M877.89.1
Created: Fanuc 15M Mitsui MZ91.89
ForUser: Braden Engineering / Caco Pacific Corp
Control: Fanuc 15M
Machine: Mitsui Seiki Horizontal
Develop: ComPost2 PPC v1.0b4, Virtual Gibbs 3.23
Comment: New processor per notes and marked up readout from, and conversation with Mark Rief.
Added G70 to first op saftey start block.
Modified WFOs to use G54.1P1 thru G54.1P48, moved to StrtPos line.
Added IndexStuff sub and calls to handle 4th axis.
Outputting B0 as default at the beginning of tools.
Added Clamp and UnClamp for Indexer.
Added PreTool.
Moved CoolOn to OfstOn line.
Moved CoolOff to OfstOff line.
Changed OfstOff from G28 to G30.
Added move to XY machine home at tool changes IF NOT ToolChangeAtHome.
Added RigidTap.
Jim Radcliffe}

{2/20/97
Initial: Fanuc 15M Mitsui MZ91.89
Created: Fanuc 15M Mitsui MZ91.89.1
Develop: ComPost2 68K 1.0b11, Virtual Gibbs 3.23
Comment: Modified per faxes and phone consultation with Mark Rief and Larry Monzon
Deleted EOR from beginning of program.
Changed G70 to G20.
Added seperator comment at the beginning of each tool.
Changed TrackZNO# ZDepth# to TrackZNO# FIRST SPZ# and added formatter for TrackZNO#.
Added custom coolant. Changed CoolOn to GetCoolOn.
Deleted SetMaxFeed and SetMaxRPM.
Jim Radcliffe}

{05/29/98,
Initial: Fanuc 15M Mitsui MZ91.89.1
Created: Fanuc 15M Mitsui [PC] MU01.89
For: Placon Corp

Changes to Form:
1) Origins & Values - Changed First Work Fixture Offset to G54. Changed Last Work
Fixture Offset to G59.

Changes to Prog:
1) Deleted all special sub-routines, including Clamp, UnClamp, ClampC, UnclampC and
Indexer.
CDH}

{7/27/98,
Initial : Fanuc 15M Mitsui [PC] MU01.89
Created: Fanuc 15M Mitsui [PC] MU01.89.1
Customer: Placon Corp. Michael Motl 608/278-4902

Changes to "Prog":

1. Added EOR (%) to program start.
JHE}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'
#7 = '#;'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4)
FORMAT(TrackZNO#,4)
FORMAT(Program#,5)
FORMAT(Operation#,5)
FORMAT(Tool#,5)
FORMAT(NewWFO#,5)
FORMAT(Parts#,5)
FORMAT(Dwell#,6)
FORMAT(RapidF#,7)

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( CYCLE START )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF MultipleParts? AND SubComment?
'( PART ' Tag# ' )' EOL
END
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
RETURN

PSStuff: {revised.72}
RETURN

DoPostScript:
PSInit
EachPS
SeqC PostScript EOL
PSStuff
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqC EndOpPS EOL
PSStuff
NextPS
RETURN

ExitType:
IF FIFO?
FeedC
ELSE
RapidC
END
RETURN

ExitFeed:
IF FIFO?
FeedEntC
END
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

StdRapid:
IF LastFeat?
SeqC CRCOffC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC RapidC MoveXYZC CRCOffsetC EOL
END
END
END
RETURN

StdLine: {enables CRC on first call, .70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC CRCOnC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
END
END
RETURN

StdArc:
EACHQuadrant
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
RETURN

ToolPath2: {for AutoCycle element moves}
EACHFeat
IF RapidFeat?
StdRapid
ELSE
IF LineFeat?
StdLine
ELSE
IF ArcFeat?
StdArc
END
END
END
NEXTFeat
RETURN

EntryMove:
IF FeedEntry?
SeqC FeedC ZInC FeedEntC EOL
ELSE
SeqC RapidC ZInC EOL
END
RETURN

CutAutoCycle:
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
SetSRXYtoSP
SeqC IncValue EOL
IF Repeats? AND ZshiftOnly?
EachRep
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
IF FeedConnect?
SeqC FeedC StrtPosC EOL
ELSE
SeqC RapidC StrtPosC EOL
END
END
END
EntryMove
ToolPath2
IF NOT FeedConnect?
SeqC ExitType PRIME ZCP2 ExitFeed EOL
END
NextRep
ELSE
EntryMove
ToolPath2
END
SeqC AbsOrInc ExitType ZCP2 ExitFeed EOL
SetSRSubXY {restore tool position}
SetSRSubMove
ReSetPass2 {restore for positioning moves}
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF AutoCycle?
IF NOT FirstFeat?
SeqC
IF FIFO?
Rapid
END
MoveSXYC EOL
END
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
CutAutoCycle
ELSE
SeqC MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
StdRapid
ELSE
IF LineFeat?
StdLine
ELSE
IF ArcFeat?
StdArc
END
END
END
END
NEXTFeat
RETURN

WFOStuff:
IF MultipleParts? AND WorkFixtureOffsets?
SetWFO
ELSE
IF NewWFO?
'G' NewWFO#
ELSE
IF NOT SameTool?
IF NeedWFO1?
WFO1
END
END
END
END
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

GetCoolOn:
IF NOT CoolOff?
IF Mist?
'M61' { Mist }
ELSE
IF ThruSpin?
'M50' { Thru Spindle }
ELSE
IF Pulse?
'M51' { Thru Side }
ELSE
CoolOn { Flood }
END
END
END
END
RETURN

DoOp:
IF FirstOperation?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
IF FullUp?
SeqC IncValue OfstOff CoolOff EOL
END
DoOpComments
ELSE
'(---------------)' EOL
Seq Plane 'G20' CRCOff DrillOff EOL
SeqC OpToolID ToolChng EOL
DoOpComments
SeqC PreTool EOL
DoPostScript
SeqC Speed SpinOn EOL
END
CheckPass
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane? AND NOT FirstPart?
SeqC Rapid StrtPos WFOStuff EOL
ELSE
SeqC AbsOrInc Rapid StrtPos WFOStuff EOL
SeqC OfstOn GetCoolOn EOL
END
ELSE
IF NewTool?
IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
{only need to set up for tool change on 1st part}
ELSE
SeqC IncValue OfstOff CoolOff EOL
DoEndOpPS
IF ToolChangeAtHome?
SeqC AbsOrInc Rapid Home SpinOff EOL
ELSE
SeqC IncValue 'G30X0.Y0.' SpinOff EOL
END
SeqC AbsOrInc EOL
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
END

{Start new Operation}

IF MultipleParts? AND OneToolAllParts? AND NOT FirstPart?
IF FullUp?
SeqC IncValue OfstOff CoolOff EOL
END
DoOpComments
ELSE
'(---------------)' EOL
Seq Plane 'G20' CRCOff DrillOff EOL
SeqC OpToolID ToolChng EOL
DoOpComments
SeqC PreTool EOL
DoPostScript
SeqC Speed SpinOn EOL
END
CheckPass
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane? AND NOT FirstPart?
SeqC Rapid StrtPos WFOStuff EOL
ELSE
SeqC AbsOrInc Rapid StrtPos WFOStuff EOL
SeqC OfstOn GetCoolOn EOL
END
ELSE
IF SameTool?

{Finish off last Operation}

SeqC
IF LAST ProgStop? OR NewToolOffset?
IncValue OfstOff
END
IF LAST ProgStop?
CoolOff
ELSE
IF CoolOff? AND LAST NOT CoolOff?
CoolOff
END
END
EOL
DoEndOpPS
IF LAST ProgStop?
SeqC SpinOff EOL
SeqC 'M0' EOL
END

{Start new Operation}

DoOpComments
DoPostScript
CheckPass
SeqC PlaneC AbsOrInc Rapid StrtPos WFOStuff SpeedC
IF LAST ProgStop?
SpinOn
END
EOL
SeqC
IF LAST ProgStop? OR NewToolOffset?
OfstOn
END
IF LAST ProgStop?
GetCoolOn
ELSE
IF NOT CoolOff? AND LAST CoolOff?
GetCoolOn
END
END
EOL
END
END
END

{ Common Point for All Operations }

ResetCRCNum {call here to reset for each new operation only, call in tool path to reset for each repeat in an operation}
RapidF# {forces the output of a conditional feedrate for each operation}

IF Milling?
SeqC ZCP2C EOL
IF Repeats?
IF ZshiftOnly? AND AutoCycle?
{done in CutAutoCycle called from ToolPath}
ELSE
EACHRep
DoSubComment
IF NOT FirstCycle?
SeqC Connect StrtPos EOL
IF NOT FeedConnect?
SeqC ZCP2C EOL
END
END
END
END
IF NOT AutoCycle?
EntryMove
END
ToolPath
IF Repeats?
IF ZshiftOnly? AND AutoCycle?
{done in CutAutoCycle called from ToolPath}
ELSE
SeqC CRCOffC
IF NOT FeedConnect?
ExitType PRIME ZCP3C
END
ExitFeed EOL
NEXTRep
END
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
SeqC CRCOffC ExitType ZCP3C ExitFeed EOL
END
ELSE
IF Drilling?
IF Repeats?
EACHRep
DoSubComment
END
SeqC DrillCP EOL
GetCycle
SeqC
IF RigidTap?
'G84.2'
ELSE
Cycle
END
FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
TrackZNO# FIRST SPZ#
ToolPath
IF RetractToCP1? {.81}
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
SeqC 'G80' EOL
IF Repeats?
NEXTRep
END
SeqC RapidC ZCP3C EOL
END
END
RETURN

FinishLastOp:
SeqC IncValue OfstOff CoolOff EOL
DoEndOpPS
IF FIRST ToolChangeAtHome?
SeqC AbsOrInc Rapid FirstHome SpinOff EOL
ELSE
SeqC IncValue 'G30X0.Y0.' SpinOff EOL
END
SeqC AbsOrInc EOL
IF MultipleParts? AND AllToolsOnePart? AND NOT LastPart? {no tool change after doing last part}
IF ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END
ELSE
SeqC EOP EOL
END
RETURN

DoToolsOps:
EachOp
IF GTEqual? Operation# Recall# Num#('1') AND LTEqual? Operation# Recall# Num#('2')
{Tools1stOp ² op ² ToolsLastOp}
DoOp
END
NextOp
RETURN

NextTools1stOp:
SetNextToolOp Operation#
RETURN

GetToolsOps:
EachOp
IF Equal? Operation# Recall# Num#('1') {if op = Tools1stOp}
IF GreaterThan? NextTools1stOp Recall# Num#('1') {if NextTools1stOp is greater Tools1stOp}
Save# Num#('2') SUB# NextTools1stOp Num#('1') {ToolsLastOp becomes NextTools1stOp less 1}
ELSE {else}
Save# Num#('2') Recall# Num#('3') {ToolsLastOp becomes ncCAMsLastOp}
END
END
NextOp
RETURN

DoTool:
IF NOT Flag?('1')
GetToolsOps
IF WorkFixtureOffsets?
NewWFO
EachWFO
TagInc
DoToolsOps
IncWFO
NextWFO
ELSE
EachPart
TagInc
DoToolsOps
NextPart
END
IF LessThan? Recall# Num#('2') Recall# Num#('3') {if ToolsLastOp < ncCAMsLastOp}
Save# Num#('1') ADD# Recall# Num#('2') Num#('1') {Tools1stOp becomes NextTools1stOp}
ELSE {else}
SetFlag('1') {set DoneFlag}
END
TagInit
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
TagInit
SetFlagF('1') {done flag}
ReverseXZArcs
InitWFONum
SetFlood
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + B move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + A move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL {Added this line - JHE}
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
END
NextOp
IF MultipleParts?
IF AllToolsOnePart?
IF WorkFixtureOffsets?
NewWFO
EachWFO
TagInc
EachOp
DoOp
NextOp
FinishLastOp
IncWFO
NextWFO
ELSE
EachPart
TagInc
EachOp
DoOp
NextOp
FinishLastOp
NextPart
END
ELSE
IF OneToolAllParts?
EachOp
IF FirstOperation?
Save# Num#('1') Operation# {ncCAMs1stOp becomes Tools1stOp}
END
IF LastOp?
Save# Num#('3') Operation# {save ncCAMsLastOp}
END
NextOp
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool DoTool
FinishLastOp
END
END
ELSE
EachOp
DoOp
NextOp
FinishLastOp
END
EOR EOL
CloseSub
Post2
IF UseComments?
SetScale('1')
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
END
Close