{Change Comments ***********************************************************}

{11/17/89
Copied & modified: GN6M Acroloc M12 M096.55
For: Skyball
Use colon for Program number.
Updated to 3.2 Version per Fanuc 6M M001.63.
Commented out SepSubs & PostScript.
JR}

{7/24/90, Added InitProg globally to posts with this remark, DWB}

{4/26/91,
Modified: GN6M Acr M12 [SM] M274.63
For: Gibbs & Associates
Updated to new 4.0 Version per Fanuc 6M M001.80
DWB}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '########;0'
#6 = '####^###;'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}

{Prog Subroutines **********************************************************}

DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF NOT SameTool?
IF ToolTypeComment?
'( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
END
IF Metric? {CAM file is in metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
END
RETURN

PSInit: {reset flags}
RETURN

PSStuff: {revised.72}
RETURN

DoPostScript:
PSInit
EachPS
{SeqC PostScript EOL} {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
{SeqC EndOpPS EOL} {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
SubID EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
UnSkipZ
SeqC CRCOffC
IF NOT FeedConnect?
RapidC ZCP3C
END
EOL
RETURN

FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqC SetWFO EOL
SeqC SubCall CallLab RepLab OnePart EOL
IncWFO
NextWFO
ELSE
SeqC SubCall CallLab RepLab Parts EOL
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
SeqC WFO1 EOL
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

FormatArc:
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

StdLine: {enables CRC on first call, .70}
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
DecelMove2
END
SeqC CRCOnC FeedC MoveXYZC DecelFeed CRCOffsetC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC CRCOnC FeedC MoveXYZC FeedRateC CRCOffsetC EOL
END
END
RETURN

ToolPath:
ResetCRCNum {.72}
EACHFeat
IF PointFeat?
SeqC MoveSXYC EOL
IF AutoCycle?
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
END
ELSE
IF RapidFeat?
IF LastFeat? AND AutoCycle? {.70}
SeqC CRCOffC RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC RapidC MoveXYZC EOL
END
END
ELSE
IF LineFeat?
IF AutoCycle? {.70}
IF LastFeat?
SeqC CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC FeedC MoveXYZC FeedRateC EOL
ELSE
StdLine {enables CRC on first call}
END
END
ELSE
StdLine
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RETURN

WFOStuff:
{ NOTE: This Post Processor does not support WorkFixtureOffsets. }
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
Seq IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
IF Repeats? AND FeedConnect? AND ZshiftOnly?
SeqC AbsOrInc EOL {.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
SeqC AbsOrInc RapidC ZCP2 EOL {.71.2 removed CRCOffC, gets turned off in ToolPath}
END
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
IF FeedConnect?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
SeqC Rapid ZCP2PlusInc EOL {.69 added Rapid, reads better}
{can't call for cycle = 1, .69 changed to ZCP2PlusInc}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL {.69 added Rapid, reads better}
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC SubCall CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
SeqC Rapid ZCP2 EOL {.69}
END {.69}
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqC SubCall CallLab EOL
NextCycle
StartSub
SkipZ
ToolPath
FinishSub1
SeqC EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
SetFlood
{UseSeparateSubCalls}
{SetMaxSeparateSubCalls ('50')}
SetMaxRPM('10000')
SetMaxFeed('500')
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
':' ProgNum EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramNameComment?
'( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
IF Metric? {CAM file is in metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
Seq AbsOrInc 'G80' CRCOff Plane Rapid EOL
SeqC OpToolID EOL
DoOpComments
DoPostScript
SeqC 'M41' TABLE(1, SpeedRPM#, 1) EOL
SeqC SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC OfstOn EOL
SeqC CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqC 'G49' EOL
DoEndOpPS
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
IF LAST ProgStop?
SeqC 'M00' EOL
ELSE
SeqC ProgStop EOL
END

{Start new Operation}

Seq AbsOrInc 'G80' CRCOff Plane Rapid EOL
SeqC OpToolID EOL
DoOpComments
DoPostScript
SeqC 'M41' TABLE(1, SpeedRPM#, 1) EOL
SeqC SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC AbsOrInc Rapid StrtPos EOL
SeqC OfstOn EOL
SeqC CoolOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC StrtPos EOL
END
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqC CoolOff EOL
SeqC IncValue OfstOff EOL
SeqC SpinOff EOL
SeqC 'M00' EOL

{Start new Operation}

SeqC 'M41' TABLE(1, SpeedRPM#, 1) SpinOn EOL
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
DoPostScript
SeqC OfstOn EOL
SeqC CoolOn EOL
ELSE
IF CoolOff? AND LAST NOT CoolOff?
SeqC CoolOff EOL
END
IF NewToolOffset?
SeqC IncValue OfstOff EOL
DoOpComments
SeqC 'M41' TABLE(1, SpeedRPM#, 1) EOL
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
DoPostScript
SeqC OfstOn EOL
ELSE
DoEndOpPS
DoOpComments
SeqC 'M41' TABLE(1, SpeedRPM#, 1) EOL
SeqC PlaneC AbsOrInc Rapid StrtPos EOL
DoPostScript
END
IF NOT CoolOff? AND LAST CoolOff?
SeqC CoolOn EOL
END
END
END
END
END {common point for all operations}
IF Milling?
SeqC ZCP2C EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
FindAnyZMoves {for normal abs subroutine}
IF NoZMoves?
ZonlyRep
ELSE
G92Sub {pattern shift, not element}
END
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
SeqC RapidC CRCOffC ZCP3C EOL
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
SeqC DrillCP EOL
GetCycle
SeqC Cycle FromCP StrtPos ZDepth RLevel Dwell Peck Retract FeedEnt EOL
ToolPath
SeqC 'G80' EOL
IF Repeats?
FinishSubG92
END
SeqC RapidC ZCP3C EOL
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
CloseMP
END
SeqC 'G49' EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
CloseMP
END
DoEndOpPS
SeqC Rapid AbsOrInc 'X0Y0T12' EOL
IF ProgStop?
SeqC 'M00' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
Close
END