{Change Comments ***********************************************************}

{9/23/88
Copied & Modified: Heidenhain TNC 145C M082.53
For: Galaxy Die & Engineering.
Machine:
Control: Heidenhain TNC 145C
Modified to have only 1 space between codes.
Added L address before Z moves.
Use Speed from ncCam.
Modified SpinOn to be M13 [CW] and M14 [CCW].
Added first and last lines.
Added M6 after tool call.
Deleted CoolOn and CoolOff commands.
Jim Radcliffe}

{11/15/88
Updated: Heid TNC151 Bridgeport M139.55
For: Galaxy Die & Engineering.
Changed all RapidF to 'F3999'.
Deleted LBL 1 thru LBL 0 lines, toolchange subroutine, from beginning of prog.
Moved HomePos & CP1 after M06 in FirstOp & NewTool.
Changed M05 to M25 for spindle up.
Added missing FORMAT for ZDepth#.
Changed ClearancePlane2# in Milling to ZCP2.
Added FORMAT #9 for cycle defs SETUP & PECKG that require a negative sign which is literal.
Deleted ZDepth# preceding IncValue and following AbsOrInc.
Changed ZDepth# in PECKG to ZDepthInc#, using FORMAT #9.
Changed FORMAT for ClearancePlane2# to FORMAT #9.
Changed FORMAT for Peck# to FORMAT #9.
Jim Radcliffe}

{7/24/90, Added InitProg globally to posts with this remark, DWB}

{11/29/90
Copied & Modified: Heid TNC151 Bridgeport M139.58
For: Phoenix Machine & Design
Machine: Interact 412
Control: Heidenhain TNC 151B/151Q
Updated to Version 3.2 per Fanuc 6M M001.76.1 Format.
Customer requests:
Added SaveProgNum2 and replaced ProgID1 with Program# at beginning and end becuase decimal point
is not allowed in opening statement.
Add ASCII('3') at end to cause DNC to stop sending.
Form changes:
Modified Rapid FeedRate (XXXX^X) from 0 to 3999
Modified 'F' default format from '00^0' to '###^0'
Prog changes:
Cleaned up FORMATs for better readability.
Added SPZ#, EPX#, EPY#, EPZ#, ArcI# and ArcJ# and FORMATs for same, for AutoCycle output
which requires literal 'I' before each axis address to indicate incremental moves.
Added FORMATs for RepeatX#, RepeatY#, RepeatZ#, OriginUnShiftRX#, OriginUnShiftRY# and
OriginUnShiftRZ# for correct output.
Added TLDia#, TLLength# and TLNum# and FORMATs for same, for Tool Definition Loop at beginning.
Added RapidF# and FORMAT for same, and replaced all literal 'F3999' to RapidF for ease of
future conversions.
DWB}

{6/19/92
Updated: Heid TNC 151 BP M139.76.1 to .81 format
Other changes for simplicity and ease of future updates or modifications.
Changed HomeX# & HomeY# to Home
Changed StartPosX# & StartPosY# to StrtPos
Changed all literal L to use the sub DoL
Changed all literal R0 to use the sub DoR0
Jim Radcliffe}

{6/19/92
Copied & modified: Heid TNC 151 BP M139.81
For: Belden Wire & Cable
Machine: Bridgeport Series 1 Interact
Control: Heidenhain TNC 151A
Summary of major changed per customer requests:
Added an asterisk before comments.
Deleted the Tool List from the beginning of program.
Modified layout of output at beginning and ending of operations.
Modified repeats of subs.
Do a ' STOP' before ' Tool Call'.
Jim Radcliffe}

{11/11/94
Copied & modified: Heid TNC 151A BP S1 M508.81
For: Neilson Machine
Summary of major changed per customer requests:
Removed M25 and STOP M from after every operation except last operation
Added support for Rigid Tapping
Changed Tool Change from Manual to Automatic by removing the STOP M
and adding "L R F M06" to the line after the "TOOL CALL"
Fixed the Spindle on command to output the right command if CoolOff?
and handle CW & CCW spindle directions
Added TOOL DEF lines for every tool to start of program and hardcoded
the L and R values to -1.5 and 0
Tom Hubina}

{10/4/95, Updated Heid TNC 151A S1 [NM] M711.81.1 to .85 format per v2.20 Update Instructions .01, JR}

{
Format: Heid TNC 151A S1 [NM] M711.85.1
11/10/95
Changed format of CallMasterNum# to #5
TH}

{12/12/95, M711.85.1, Updated for Catalyst v2.20 per Fanuc 6M M001.85.02 Format, DWB}

{6/4/96, Updated Heid TNC 151A S1 [NM] M711.85.2 to .89 format per Fanuc 6M M001.89, JR}

{12/2/98, added suuport for helical milling in FormatArc. This is only for XY plane.
MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = 'ą####0.0000'
#5 = '#######0'
#6 = '####0.000'
#7 = '+####0.0000'
#8 = '###^0'
#9 = 'ą####0.000'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ClearancePlane1#,4)
FORMAT(StartPosX#,4)
FORMAT(StartPosY#,4)
FORMAT(SPX#,4)
FORMAT(SPY#,4)
FORMAT(SPZ#,4)
FORMAT(EPX#,4)
FORMAT(EPY#,4)
FORMAT(EPZ#,4)
FORMAT(ArcI#,4)
FORMAT(ArcJ#,4)
FORMAT(ZDepth#,4)
FORMAT(RepeatX#,4)
FORMAT(RepeatY#,4)
FORMAT(RepeatZ#,4)
FORMAT(PartShiftX#,4)
FORMAT(PartShiftY#,4)
FORMAT(PartShiftZ#,4)
FORMAT(OriginUnShiftPX#,4)
FORMAT(OriginUnShiftPY#,4)
FORMAT(OriginUnShiftPZ#,4)
FORMAT(OriginUnShiftRX#,4)
FORMAT(OriginUnShiftRY#,4)
FORMAT(OriginUnShiftRZ#,4)
FORMAT(FeedTapIPR#,4)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(TLDia#,4)
FORMAT(TLLength#,4)
FORMAT(TLNum#,5)
FORMAT(CallMasterNum#,5)
FORMAT(Program#,5) {.72}
FORMAT(Program2#,5)
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}
FORMAT(ClearancePlane2#,7)
FORMAT(ZDepthInc#,7)
FORMAT(Peck#,7)
FORMAT(FeedEntry#,8)
FORMAT(RapidF#,8)
FORMAT(ArcAngle#,9)

{Special Subs **************************************************************}

DoL:
' L'
RETURN

DoZL:
' L'
RETURN

Space: { 0 Spaces }
''
RETURN

XYZSpace:
'' Space
RETURN

XYSpace:
'' Space Space
RETURN

ZSpace:
'' Space Space Space
RETURN

IXYZSpace:
Space
RETURN

IXYSpace:
Space Space
RETURN

IZSpace:
Space Space Space
RETURN

DoR0:
IF NOT Flag?('3') { ArcFeat }
''
END
IF Flag?('2') { CutterRadiusCompensation }
IF CRCleft?
' RL'
ELSE
' RR'
END
ELSE
' R0'
END
RETURN

RF: { RapidF }
' F3999'
RETURN

DoM:
' M'
RETURN

ckCRCOff:
IF Flag?('2') { CRCOn }
SetFlagF('2')
SeqLab DoL ' IX+0.0000 IY+0.0000' IXYSpace DoR0 RF DoM EOL
END
RETURN

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? { CAM file is in Metric, tools and tool path }
SetScale('.03937007874') { change to English, this is an English post }
ELSE
SetScale('1')
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'*( SUB NUMBER: ' Program# ' )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'*( OPERATION ' Operation# ': ' OperationType$ ' )' EOL
END
IF OperationComment?
'*( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'*( ' WorkGroupComment$ ' )' EOL
END
IF ToolTypeComment?
'*( TOOL ' Tool# ': ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'*( ' ToolComment$ ' )' EOL
END
RestoreScale
END
RETURN

PSInit: {reset flags}
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqLab ' A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqLab ' A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqLab ' B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqLab ' B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
SeqLab PostScript EOL {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
SeqLab EndOpPS EOL {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
SeqLab DoZL
IF NOT AbsValue?
' IZ' SPZ# IZSpace
ELSE
ZIn ZSpace
END
DoR0
IF FeedEntry?
Feed {no output}
FeedEnt Space
ELSE
RF
END
DoM EOL
RETURN

StartSub:
OpenSub
SeqLab ' LBL ' Program# EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'*( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqLab ' CALL LBL ' Program# EOL
StartSub
RETURN

FinishSub1: {part 1}
IF NOT FeedConnect?
SeqLab DoZL ZCP3 ZSpace
IF Flag?('2') { CRCOn }
SetFlagF('2')
DoR0
SetFlag('2')
ELSE
DoR0
END
IF AutoCycle?
RF
ELSE
IF FIFO? {.81}
Feed {no output}
FeedEnt Space
ELSE
RF
END
END
DoM EOL
END
ckCRCOff
RETURN

FinishSubG92: {part 2}
SeqLab ' CYCL DEF 7.0 DATUM SHIFT' EOL
SeqLab ' CYCL DEF 7.1 IX' RepeatX# EOL
SeqLab ' CYCL DEF 7.2 IY' RepeatY# EOL
SeqLab ' CYCL DEF 7.3 IZ' RepeatZ# EOL
SeqLab ' CALL LBL ' Program# ' REP ' RepsLess1 '/ ' RepsLess1 EOL
SeqLab ' LBL 0' EOL
CloseSub
SeqLab ' CYCL DEF 7.0 DATUM SHIFT' EOL
SeqLab ' CYCL DEF 7.1 IX' OriginUnShiftRX#('0') EOL
SeqLab ' CYCL DEF 7.2 IY' OriginUnShiftRY#('0') EOL
SeqLab ' CYCL DEF 7.3 IZ' OriginUnShiftRZ#('0') EOL
RETURN

OpenMP:
IF EquallySpacedOffsets?
NewProg
SeqLab ' CALL LBL ' Program# EOL
StartSub
END
RETURN

CloseMP:
IF EquallySpacedOffsets?
SeqLab ' CYCL DEF 7.0 DATUM SHIFT' EOL
SeqLab ' CYCL DEF 7.1 IX' PartShiftX# EOL
SeqLab ' CYCL DEF 7.2 IY' PartShiftY# EOL
SeqLab ' CYCL DEF 7.3 IZ' PartShiftZ# EOL
SeqLab ' CALL LBL ' Program# ' REP ' PartsLess1 ' / ' PartsLess1 EOL
SeqLab ' LBL 0' EOL
CloseSub
SeqLab ' CYCL DEF 7.0 DATUM SHIFT' EOL
SeqLab ' CYCL DEF 7.1 IX' OriginUnShiftPX#('0') EOL
SeqLab ' CYCL DEF 7.2 IY' OriginUnShiftPY#('0') EOL
SeqLab ' CYCL DEF 7.3 IZ' OriginUnShiftPZ#('0') EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
SetInc
ELSE
IF NOT ZMove? AND NOT AbsValue?
SetAbs
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
SetInc
ELSE
IF NOT SPZMove? AND NOT AbsValue?
SetAbs
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SetAbs
END
RETURN

CheckMove:
IF AutoCycle? OR NOT AbsValue?
IF XMove? OR YMove? OR ArcFeat?
' IX' EPX# ' IY' EPY#
IF ZMove?
' IZ' EPZ# IXYZSpace
ELSE
IXYSpace
END
ELSE
IF ZMove?
' IZ' EPZ# IZSpace
END
END
ELSE
IF XMove? OR YMove? OR ArcFeat?
MoveX MoveY
IF ZMove?
MoveZC XYZSpace
ELSE
XYSpace
END
ELSE
IF ZMove?
MoveZC ZSpace
END
END
END
RETURN

ckCRC:
IF CutterRadiusCompensation?
IF LastFeat?
SetFlagF('2') { CRCOff }
ELSE
IF NOT ZMove?
SetFlag('2') { CRCOn }
END
END
END
RETURN

FormatArc:
DoAbsOrInc
SeqLab ' CC'
IF AutoCycle? OR NOT AbsValue? {implies incremental}
' IX' ArcI# ' IY' ArcJ#
ELSE
ArcIJ
END
EOL
IF ZMove?
IF NOT AbsValue?
SetFlag('4')
END
SeqLab ' CPIPA' ArcAngle# SetInc ' IZ' EPZ#
IF NOT Flag?('4')
SetAbs
END
ELSE
SeqLab ' C' CheckMove
END
IF ArcCW?
' DR-' CWArc {no output}
ELSE
' DR+' CCWArc {no output}
END
SetFlag('3')
DoR0
SetFlagF('3')
RETURN

FormatLine:
IF ZMove? AND NOT XMove? AND NOT YMove?
DoZL
ELSE
DoL
END
DoAbsOrInc CheckMove CkCRC DoR0
RETURN

ToolPath:
EACHFeat
IF PointFeat?
IF NOT FirstFeat?
Rapid {no output}
IF AutoCycle?
SeqLab DoL MoveSX MoveSY XYSpace DoR0 RF DoM EOL
ELSE
SeqLab DoL DoDrillAbsOrInc
IF AbsValue?
MoveSX MoveSY
IF SPZMove?
MoveSZ XYZSpace
ELSE
XYSpace
END
ELSE
' IX' SPX# ' IY' SPY# ' IZ' SPZ# IXYZSpace
END
DoR0 RF ' M99' EOL
END
END
IF AutoCycle?
SeqLab ' CALL LBL ' Program# EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
END
ELSE
IF RapidFeat?
Rapid {no output}
IF XMove? OR YMove? OR ZMove?
SeqLab FormatLine RF DoM EOL
END
ELSE
IF LineFeat?
Feed {no output}
IF XMove? OR YMove? OR ZMove?
SeqLab FormatLine FeedRate Space DoM EOL
END
ELSE
IF ArcFeat?
EACHQuadrant
FormatArc ArcFeed Space DoM EOL
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

WFOStuff:
{ NOTE: This Post Processor does not support WorkFixtureOffsets. }
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
SetInc
RETURN

AutoCycCutSub2: {part 2}
ToolPath
SetAbs
IF Repeats? AND FeedConnect? AND ZshiftOnly?
{.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
SeqLab DoZL ZCP2 ZSpace DoR0
IF FIFO? {.81}
FeedEnt Space
ELSE
RF
END
DoM EOL
END
SeqLab ' LBL 0' EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SetAbs
SeqLab DoL StrtPos XYSpace DoR0
IF FeedConnect?
FeedEnt Space
ELSE
RF
END
DoM EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
Feed {no output}
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SetInc
SeqLab DoL ' IX' StartPosX# ' IY' StartPosY# IXYSpace DoR0 FeedEnt Space DoM EOL
SetAbs
END
END
SeqLab DoZL ZInPlusInc ZSpace DoR0 FeedEnt Space DoM EOL
ELSE
IF NOT FirstCycle?
Rapid {no output}
IF SPXMove? OR SPYMove?
SetInc
SeqLab DoL ' IX' StartPosX# ' IY' StartPosY# IXYSpace DoR0 RF DoM EOL
SetAbs
END
IF FeedEntry?
SeqLab DoZL ZCP2PlusInc ZSpace DoR0 RF DoM EOL
Feed {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 FeedEnt Space DoM EOL
ELSE
SeqLab DoZL ZInPlusInc ZSpace DoR0 RF DoM EOL
END
ELSE
IF FeedEntry?
Feed {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 FeedEnt Space DoM EOL
ELSE
Rapid {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 RF DoM EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqLab ' CALL LBL ' Program# EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
IF FeedConnect? {there is no Z up in the sub, .69}
Rapid {no output}
SeqLab DoZL ZCP2 ZSpace DoR0
IF FIFO? {.81}
FeedEnt Space
ELSE
RF
END
DoM EOL {.69}
END {.69}
SeqLab ' LBL 0' EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqLab DoL StrtPos XYSpace DoR0
IF FeedConnect?
FeedEnt Space
ELSE
RF
END
DoM EOL
END
IF FeedConnect?
Feed {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 FeedEnt Space DoM EOL
ELSE
IF FeedEntry?
IF NOT FirstCycle?
Rapid {no output}
SeqLab DoZL ZCP2PlusIncC ZSpace DoR0 RF DoM EOL
END
Feed {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 FeedEnt Space DoM EOL
ELSE
Rapid {no output}
SeqLab DoZL ZInPlusInc ZSpace DoR0 RF DoM EOL
END
END
SeqLab ' CALL LBL ' Program# EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqLab ' LBL 0' EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
SaveProgNum2
SetFlagF('1') { Milling ZShiftOnly SepSubs }
SetFlagF('2') { CRCOff }
SetFlagF('3') { ArcFeat }
SetFlagF('4') { ArcFeat }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END

IF MultipleParts? AND WorkFixtureOffsets?
'*( *** WARNING *** )' EOL
'*( THIS POST PROCESSOR DOES NOT SUPPORT WORKFIXTURE OFFSETS. )' EOL
'*( PLEASE SELECT EQUALLY SPACED OFFSETS. )' EOL
'*( *** WARNING *** )' EOL
END

EachOp {Start of post processing *********************}
IF FirstOperation?
SeqLab ' BEGIN PGM ' Program# ' INCH' EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramNameComment?
'*( PROGRAM: ' ProgramName$ ' )' EOL
END
IF ProgramComment?
'*( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'*( FORMAT: ' FormatName$ ' )' EOL
END
IF TimeComment?
'*( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'*( OUTPUT IN ABSOLUTE INCHES )' EOL
END
IF PartsComment?
'*( PARTS PROGRAMMED: ' Parts# ' )' EOL
END
IF StartToolComment?
'*( FIRST TOOL NOT IN SPINDLE )' EOL
END
END
OpenSub
SetAbs
Plane Rapid {no output}
EachTool
SetScale('1')
SeqLab ' TOOL DEF ' TLNum#
RestoreScale
DoL '-1.5 R0.0'
EOL
NextTool
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
SeqLab DoL
IF ToolChangeAtHome?
Home XYSpace
END
DoR0 RF ' M' EOL

DoOpComments
DoPostScript
SeqLab ' TOOL CALL ' Tool# ' Z' Speed EOL
SeqLab DoL ' R F M06' EOL
IF MultipleParts? AND OneToolAllParts?
OpenMP
END
CheckPass
SeqLab DoL StrtPos XYSpace DoR0 RF
IF CoolOff?
' ' SpinOn
ELSE
IF CWSpindle?
' M13'
ELSE
' M14'
END
END
EOL
SeqLab DoZL ' Z' ClearancePlane1# ZSpace DoR0 RF DoM EOL
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts?
CloseMP
END
DoEndOpPS
SeqLab DoL
IF ToolChangeAtHome?
Home XYSpace
END

DoR0 RF ' M' EOL

{Start new Operation}

SetAbs
Plane Rapid {no output}
DoOpComments
DoPostScript
SeqLab ' TOOL CALL ' Tool# ' Z' Speed EOL
SeqLab DoL ' R F M06' EOL
IF MultipleParts? AND OneToolAllParts?
OpenMP
END
CheckPass
SeqLab DoL StrtPos XYSpace DoR0 RF
IF CoolOff?
SpinOn
ELSE
IF CWSpindle?
' M13'
ELSE
' M14'
END
END
EOL
SeqLab DoZL ' Z' ClearancePlane1# ZSpace DoR0 RF DoM EOL
ELSE
IF SameTool?
DoEndOpPS
IF LAST ProgStop?
SeqLab DoL DoR0 RF ' M' EOL
END

{Start new Operation}

DoOpComments
DoPostScript
CheckPass
SetAbs
Plane Rapid {no output}
SeqLab DoL StrtPos XYSpace DoR0 RF DoM EOL
IF LAST ProgStop?
SeqLab DoZL ' Z' ClearancePlane1# ZSpace DoR0 RF DoM EOL
END
END
END
END {common point for all operations}
IF Milling?
SeqLab DoZL ZCP2 ZSpace DoR0 RF DoM EOL
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
LoadFeat Num#('0') Num#('0') ClearancePlane3#
IF ZMove?
SeqLab DoZL ZCP3 ZSpace
IF Flag?('2') { CRCOn }
SetFlagF('2')
DoR0
SetFlag('2')
ELSE
DoR0
END
IF AutoCycle?
RF
ELSE
IF FIFO? {.81}
Feed {no output}
FeedEnt Space
ELSE
RF
END
END
DoM EOL
END
ckCRCOff
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqLab DoL StrtPos XYSpace DoR0 RF DoM EOL
END
IF NOT RetractToCP1?
SeqLab DoZL ZCP2 ZSpace DoR0 RF DoM EOL
END
GetCycle
IF Tap?
IF OptCyc1?
SeqLab ' CYCL DEF 17.0 RIGID TAPPING' EOL
SeqLab ' CYCL DEF 17.1 SETUP -' ClearancePlane2# EOL
SeqLab ' CYCL DEF 17.2 DEPTH ' ZDepth# EOL
SeqLab ' CYCL DEF 17.3 PITCH ' FeedTapIPR# ('1') EOL
ELSE
SeqLab ' CYCL DEF 2.0 TAPPING' EOL
SeqLab ' CYCL DEF 2.1 SETUP -' ClearancePlane2# EOL
SeqLab ' CYCL DEF 2.2 DEPTH ' ZDepth# EOL
SeqLab ' CYCL DEF 2.3 DWELL 0' EOL
SeqLab ' CYCL DEF 2.4 F' FeedEntry# EOL
END
ELSE
SeqLab ' CYCL DEF 1.0 PECKING' EOL
SeqLab ' CYCL DEF 1.1 SETUP -' ClearancePlane2# EOL
SeqLab ' CYCL DEF 1.2 DEPTH ' ZDepth# EOL
SeqLab ' CYCL DEF 1.3 PECKG -'
IF Peck?
Peck#
ELSE
ZDepthInc#
END
EOL
SeqLab ' CYCL DEF 1.4 DWELL '
IF Dwell?
Dwell#
ELSE
'0'
END
EOL
SeqLab ' CYCL DEF 1.5 F' FeedEntry# EOL
END
IF CallMasterOp?
SeqLab ' CALL LBL ' CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqLab ' CALL LBL ' Program# EOL
StartSub
SeqLab DoL StrtPos XYSpace DoR0 RF ' M99' EOL
ToolPath
SeqLab ' LBL 0' EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
SeqLab DoL StrtPos XYSpace DoR0 RF ' M99' EOL
ToolPath
END
END
{SetDrillEndOpZ}
Rapid {no output}
SeqLab DoZL ZCP3 ZSpace DoR0 RF DoM EOL
IF Repeats?
FinishSubG92
END
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts?
CloseMP
END
DoEndOpPS
Rapid {no output}
SeqLab DoL
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
FirstHome XYSpace
END
DoR0 RF ' M25' EOL
IF ProgStop?
SeqLab ' STOP M02' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqLab ' STOP M02' EOL
Post
Close
Reopen
IF UseComments?
SetScale('1') {restore scale for comments}
IF FileBytesComment?
'*( FILE LENGTH: ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'*( FILE LENGTH: ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'*( FILE LENGTH: ' FileMeters# ' METERS )' EOL
END
END
SeqLab ' END PGM ' Program2# ' INCH' EOL
ASCII('3') EOL
Close
Retag