{Change Comments ***********************************************************}

{10/31/89
Copied & modified: Fan 6M MS MV35 [¨] M051.55
For: Accutool
Machine: Matsura RA2
Control: Yasnac MX3
Modified per customer requests.
JR}

{7/24/90, Added InitProg globally to posts with this remark, DWB}

{4/26/91,
Modified: Yasnac MX3 Mat [AM] M267.62
For: Gibbs & Associates
Updated to new 4.0 Version per Fanuc 6M M001.80
DWB}

{8/31/95, Updated Yasnac MX3 Mat [AM] M267.79 to .85 version per Fanuc 6M M001.85.01.03, JR}

{1/17/96, Updated .85 to .86 version, MPK}

{3/22/96, Tested ZOnlyRepAutoCycle, Changed version # to .89, MPK}

{Prog Numeric Format Definitions *******************************************}

#1 = '#.00'
#2 = '###.###;0.'
#3 = '*###.###;0.'
#4 = '####.####;0.'
#5 = '#######0'
#6 = '####^##0'

FORMAT(FileFeet#,1)
FORMAT(FileMeters#,1)
FORMAT(ToolDiameter#,4) {.72}
FORMAT(Program#,5) {.72}
FORMAT(CallMasterNum#,5)
FORMAT(Operation#,5) {.72}
FORMAT(Tool#,5) {.72}
FORMAT(NewWFO#,5) {.72}
FORMAT(Parts#,5) {.72}
FORMAT(Dwell#,6) {.72}

{Prog Subroutines **********************************************************}

RestoreScale:
IF Metric? {CAM file is in Metric, tools and tool path}
SetScale('.03937007874') { change to English, this is an English post}
END
RETURN

DoSubComment:
IF UseComments? AND SubComment?
'( SUB NUMBER- ' Program# ' )' EOL
END
RETURN

DoOpComments:
IF UseComments?
SetScale('1')
IF OperationIDComment?
'( OPERATION ' Operation# '- ' OperationType$ ' )' EOL
END
IF OperationComment?
'( ' OperationComment$ ' )' EOL
END
IF WorkGroupComment?
'( ' WorkGroupComment$ ' )' EOL
END
IF NOT SameTool?
IF ToolTypeComment?
'( TOOL ' Tool# '- ' ToolDiameter# ' ' ToolType$ ' )' EOL
END
IF ToolComment?
'( ' ToolComment$ ' )' EOL
END
END
RestoreScale
END
RETURN

PSInit: {reset flags}
NewWFOF
RotateF
OptCyc1F
MasterOpF
CallMasterOpF
RETURN

PSStuff: {revised.72}
IF FourthCW?
FORMAT(FourthDegree#,2)
SeqC 'A' FourthDegree# EOL
FourthCWF {reset flag}
END
IF FourthCCW?
FORMAT(FourthDegree#,3)
SeqC 'A' FourthDegree# EOL
FourthCCWF {reset flag}
END
IF FifthCW?
FORMAT(FifthDegree#,2)
SeqC 'B' FifthDegree# EOL
FifthCWF {reset flag}
END
IF FifthCCW?
FORMAT(FifthDegree#,3)
SeqC 'B' FifthDegree# EOL
FifthCCWF {reset flag}
END
RETURN

DoPostScript:
PSInit
EachPS
{SeqC PostScript EOL} {literals}
PSStuff {commands}
NextPS
RETURN

DoEndOpPS:
PSInit
EachEOPS
{SeqC EndOpPS EOL} {literals}
PSStuff {commands}
NextPS
RETURN

EntryMove:
IF FeedEntry?
SeqC Feed ZIn FeedEnt EOL
ELSE
SeqC RapidC ZIn EOL
END
RETURN

StartSub:
OpenSub
SubID EOL
DoSubComment
RETURN

SubWarning:
IF NOT FeedConnect?
IF AnyZshift?
' ' EOL
'( WARNING Z CLEARANCE WILL CHANGE WITH EACH CYCLE OF SUB REPEAT )' EOL
' ' EOL
END
END
RETURN

StdSub:
SeqC SubCall CallLab RepLab RepCycs EOL
StartSub
RETURN

FinishSub1: {part 1}
SeqC
IF NOT FeedConnect?
IF AutoCycle?
ZCP3C
ELSE
IF FIFO? {.81}
FeedC ZCP3C FeedEntC
ELSE
RapidC ZCP3C
END
END
END
EOL
SeqC CRCOffC EOL
RETURN

FinishSubG92: {part 2}
SeqC Preset ShiftRC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftRC EOL
RETURN

OpenMP:
NewProg
IF WorkFixtureOffsets?
NewWFO
EachWFO
SeqC SetWFO SubCall CallLab RepLab OnePart EOL
IncWFO
NextWFO
ELSE
SeqC SubCall CallLab RepLab Parts EOL
END
StartSub
RETURN

CloseMP:
IF WorkFixtureOffsets?
SeqC EndSub EOL
CloseSub
WFO1
ELSE
SeqC Preset ShiftPC EOL
SeqC EndSub EOL
CloseSub
SeqC Preset UnshftPC EOL
END
RETURN

DoAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF ZMove? AND AbsValue?
IncValue
ELSE
IF NOT ZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

DoDrillAbsOrInc:
IF Flag?('1') AND AbsoluteMoves?
IF SPZMove? AND AbsValue?
IncValue
ELSE
IF NOT SPZMove? AND NOT AbsValue?
AbsValue
END
END
END
RETURN

RestoreAbsOrInc:
IF Flag?('1') AND AbsoluteMoves? AND NOT AbsValue?
SeqC AbsValue EOL
END
RETURN

FormatArc:
DoAbsOrInc
IF ArcCW?
CWArcC
ELSE
CCWArcC
END
MoveXYZC
IF ArcIJFormat?
ArcIJC
ELSE
ArcRC
END
RETURN

ToolPath:
ResetCRCNum
EACHFeat
IF PointFeat?
IF AutoCycle?
SeqC MoveSXYC EOL
SeqC SubCall CallLab EOL
CalcACSRXY {calc tool position after sub call, CalcAutoCycleStatusRecordXY}
ELSE
SeqC DoDrillAbsOrInc MoveSXYZC EOL {.80.01}
END
ELSE
IF RapidFeat?
IF LastFeat?
SeqC DoAbsOrInc CRCOffC RapidC MoveXYZC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC DoAbsOrInc RapidC MoveXYZC EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC DoAbsOrInc CRCOnC RapidC CRCOffsetC MoveXYZC EOL
END
END
END
ELSE
IF LineFeat?
IF LastFeat?
SeqC DoAbsOrInc CRCOffC FeedC MoveXYZC FeedRateC EOL
ELSE
IF ZMove? {skip CRCOn until first non-Z move line, skipping ramps}
SeqC DoAbsOrInc FeedC MoveXYZC FeedRateC EOL
ELSE
IF Decelerate?
IF RoomToDecel?
DecelMove1
SeqC DoAbsOrInc CRCOnC FeedC CRCOffsetC MoveXYZC FeedRateC EOL
DecelMove2
END
SeqC DoAbsOrInc CRCOnC FeedC CRCOffsetC MoveXYZC DecelFeed EOL
ELSE
IF XMove? OR YMove? OR ZMove?
SeqC DoAbsOrInc CRCOnC FeedC CRCOffsetC MoveXYZC FeedRateC EOL
END
END
END
END
ELSE
IF ArcFeat?
EACHQuadrant { Do not use NOT, FIRST, LAST or NEXT modifiers in this loop }
IF LastQuadrant? AND Decelerate?
IF RoomToDecel?
DecelMove1
SeqC FormatArc ArcFeedC EOL
DecelMove2
END
SeqC FormatArc DecelFeed EOL
ELSE
SeqC FormatArc ArcFeedC EOL
END
NEXTQuadrant
END
END
END
END
NEXTFeat
RestoreAbsOrInc
RETURN

WFOStuff:
IF NewWFO?
IF MultipleParts?
EOL
'*** WARNING *** DO NOT USE NEWWFO() WITH NCPOST MULTIPLE PARTS' EOL
SeqC
ELSE
'G' NewWFO#
END
ELSE
IF NOT SameTool?
IF NeedWFO1?
'G' NewWFO#
END
END
END
RETURN

AutoCycCutSub1: {part 1}
SaveSubStatus {save tool position}
SetPass1 {element cut moves}
StartSub
SetSRXYtoSP
Seq IncValue EOL
RETURN

AutoCycCutSub2: {part 2}
ToolPath
IF Repeats? AND FeedConnect? AND ZshiftOnly?
SeqC AbsOrInc EOL {.69 removed RapidC} {.71.2 removed CRCOffC, gets turned off in ToolPath}
ELSE
SeqC AbsOrInc
IF FIFO? {.81}
FeedC ZCP2 FeedEntC
ELSE
RapidC ZCP2
END
EOL {.71.2 removed CRCOffC, gets turned off in ToolPath}
END
SeqC EndSub EOL
CloseSub
SetSRSubXY {restore SR to 1st position value}
SetSRSubMove
RETURN

AutoCycPat:
SetPass2 {position pattern}
ToolPath {call after NewProg for correct sub calls}
SetPass1 {reset}
RETURN

Milling:
IF AutoCycle?
NewProg
AutoCycCutSub1
EntryMove
AutoCycCutSub2
AutoCycPat
ELSE
EntryMove
ToolPath
END
RETURN

G92Sub:
SubWarning
StdSub
SeqC AbsOrInc Connect StrtPos EOL
Milling
FinishSub1
FinishSubG92
RETURN

ZonlyRepAutoCycle:
AutoCycPat {write pattern moves and main calls}
StartSub
NewProg
EachCycle
SetSRXYtoEP
IF FeedConnect?
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC Feed IncValue StrtPosC EOL
SeqC AbsOrInc
ELSE
SeqC Feed
END
ELSE
SeqC Feed
END
ZInPlusInc FeedEnt EOL
ELSE
IF NOT FirstCycle?
IF SPXMove? OR SPYMove?
SeqC Rapid IncValue StrtPosC EOL
IF FeedEntry?
SeqC AbsOrInc ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC AbsOrInc ZInPlusInc EOL
END
ELSE
IF FeedEntry?
SeqC Rapid ZCP2PlusInc EOL
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
ELSE
IF FeedEntry?
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC Rapid ZInPlusInc EOL
END
END
END
IF FirstCycle?
SetStatusOff {protect Z position for incremental sub}
END
SeqC SubCall CallLab EOL
NextCycle
SetStatusOn
AutoCycCutSub1 {build element sub}
AutoCycCutSub2
{.69, removed FinishSub1}
IF FeedConnect? {there is no Z up in the sub, .69}
IF FIFO? {.81}
SeqC Feed ZCP2 FeedEnt EOL {.69}
ELSE
SeqC Rapid ZCP2 EOL {.69}
END
END {.69}
SeqC EndSub EOL
CloseSub
{Element shift, not pattern}
RETURN

ZonlyRep:
EachCycle
IF NOT FirstCycle?
SeqC Connect StrtPos EOL {.71.2, added Connect}
END
IF FeedConnect?
SeqC FeedC ZInPlusInc FeedEnt EOL {.71.2, changed to FeedC}
ELSE {Entry/Exit Connect}
IF FeedEntry?
IF NOT FirstCycle?
SeqC RapidC ZCP2PlusIncC EOL {can't call for cycle =1} {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
SeqC Feed ZInPlusInc FeedEnt EOL
ELSE
SeqC RapidC ZInPlusInc EOL {.69 added Rapid, reads better} {.71.2, changed to RapidC, reads better}
END
END
SeqC SubCall CallLab EOL
NextCycle
StartSub
TrackZNO# FIRST SPZ#
ToolPath
FinishSub1
SeqC EndSub EOL
CloseSub
RETURN

CheckPass:
IF AutoCycle? {use the correct StrtPos}
SetPass2
ELSE
SetPass1
END
RETURN

SkipToLastFeat:
EachFeat
IF LastFeat?
TrackXNO# SPX#
TrackYNO# SPY#
END
NextFeat
RETURN

SetDrillEndOpZ:
IF RetractToCP1?
TrackZNO# ClearancePlane1#
ELSE
TrackZNO# ClearancePlane2#
END
RETURN

{Start of executable Prog **************************************************}

{setup and initializations}
InitProg
ReverseXZArcs
InitWFONum
SetFlood
UseSeparateSubCalls
SetMaxSeparateSubCalls('50')
SetMaxRPM('10000')
SetMaxFeed('500')
SetFlagF('1') { Milling ZShiftOnly SepSubs }
IF PSComment? AND UseComments?
'PostScript:' EOL
' Literals: put between single or double quotes.' EOL
' Separate commands and literals with at least one space.' EOL
' A CR ( RETURN key ) will start a new line.' EOL
' Commands: may be capital and/or lower case letters. Separate commands with a space.' EOL
' EndOP -' EOL
' all literals and commands before an ENDOP command' EOL
' will appear at the beginning of the operation. All ' EOL
' literals and commands after an ENDOP command will appear' EOL
' at the end of the operation. ' EOL
' NewWFO(56), NWFO(56) -' EOL
' The Work Fixture Offset # you specify will be used for all following operations.' EOL
' Do not use with the ncPost multiple part option.' EOL
' 4thAxisCW(12.5), 4ACW(12.5) -' EOL
' generates a + A move of the value you specify' EOL
' 4thAxisCCW(22.5), 4ACCW(22.5) -' EOL
' generates a - A move of the value you specify' EOL
' 5thAxisCW(30), 5ACW(30) -' EOL
' generates a + B move of the value you specify' EOL
' 5thAxisCCW(22.5), 5ACCW(22.5) -' EOL
' generates a - B move of the value you specify' EOL
END
EachOp {Start of post processing *********************}
IF FirstOperation?
EOR EOL
ProgID1
IF UseComments? AND ProgramNameComment?
'( PROGRAM- ' ProgramName$ ' )'
END
EOL
IF ToolChangeAtHome?
SetHome
END
IF UseComments?
IF ProgramComment?
'( ' ProgramComment$ ' )' EOL
END
IF FormatNameComment?
'( FORMAT- ' FormatName$ ' )' EOL
END
IF TimeComment?
'( ' Date$ ' AT ' Time$ ' )' EOL
END
IF MovesComment?
'( OUTPUT IN ' MoveType$ ' INCHES )' EOL
END
IF PartsComment?
'( PARTS PROGRAMMED- ' Parts# ' )' EOL
END
IF StartToolComment?
'( FIRST TOOL IN SPINDLE )' EOL
END
END
OpenSub
RestoreScale
IF MultipleParts? AND AllToolsOnePart?
OpenMP
END
ASCII('13') EOL
DoOpComments
DoPostScript
Seq Rapid Plane CRCOff DrillOff AbsOrInc EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC WFOStuff StrtPos EOL
SeqC OfstOn Speed SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC Rapid StrtPos EOL
END
SeqC
IF Milling?
ZCP2C
END
CoolOn
IF NOT LastTool?
PreTool
END
EOL
ELSE
IF NewTool?

{Finish off last Operation}

IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
EOL
CloseMP
SeqC
END
CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
SeqC OfstOff EOL
DoEndOpPS
CloseMP
SeqC SpinOff EOL
SeqC 'M19' EOL
ELSE
SeqC SpinOff EOL
SeqC OfstOff 'M19' EOL
DoEndOpPS
END
IF ToolChangeAtHome?
SeqC Rapid Home ToolChng EOL
ELSE
SeqC ToolChng EOL
END
IF LAST ProgStop?
SeqC 'M0' EOL
ELSE
SeqC ProgStop EOL
END

{Start new Operation}

ASCII('13') EOL
DoOpComments
Seq Rapid Plane CRCOff DrillOff AbsOrInc EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
OpenMP
END
CheckPass
SeqC WFOStuff StrtPos EOL
DoPostScript
SeqC OfstOn Speed SpinOn EOL
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
OpenMP
SeqC Rapid StrtPos EOL
END
SeqC
IF Milling?
ZCP2C
END
CoolOn PreTool EOL
ELSE
IF SameTool?
IF LAST ProgStop? OR CoolOff? AND LAST NOT CoolOff?
CoolOff
END
EOL
IF LAST ProgStop? OR NewToolOffset?
SeqC IncValue OfstOff EOL
END
DoEndOpPS
IF LAST ProgStop?
SeqC SpinOff EOL
SeqC 'M0' EOL
END

{Start new Operation}

DoOpComments
DoPostScript
CheckPass
SeqC Rapid PlaneC WFOStuff StrtPos SpeedC
IF LAST ProgStop?
SpinOn
END
EOL
IF LAST ProgStop? OR NewToolOffset?
SeqC OfstOn EOL
END
SeqC
IF Milling?
ZCP2C
ELSE
ZCP1C
END
IF LAST ProgStop? OR NOT CoolOff? AND LAST CoolOff?
CoolOn
END
EOL
END
END
END {common point for all operations}
IF Milling?
IF Repeats?
NewProg
IF ZshiftOnly?
IF AutoCycle? {incremental Autocycle sub can have Z moves}
ZonlyRepAutoCycle
ELSE {Z shift only, NOT Auto Cycle}
IF UseSeparateSubCalls? AND CyclesLessThanMaxSubCalls?
SetFlag('1') { Milling ZShiftOnly SepSubs }
ZonlyRep
SetFlagF('1')
ELSE {no sep subs desired}
G92Sub
END
END {end Auto Cycle IF}
ELSE {not Z only}
G92Sub
END {end Z only IF}
ELSE {no repeat OPs}
Milling
END
IF AutoCycle?
SeqC ZCP3C EOL
ELSE
IF FIFO? {.81}
SeqC FeedC ZCP3C FeedEntC EOL
ELSE
SeqC RapidC ZCP3C EOL
END
END
SeqC CRCOffC
ELSE
IF Drilling?
IF Repeats?
NewProg
StdSub
SeqC AbsOrInc Rapid StrtPos EOL
END
GetCycle
SeqC FromCP Cycle ZDepth RLevel Dwell Peck Retract FeedEnt EOL
IF CallMasterOp?
SeqC SubCall CallLabB CallMasterNum# EOL
SkipToLastFeat
ELSE
TrackZNO# FIRST SPZ#
IF MasterOp?
SetFlag('1') {std sep sub Zreps in effect}
NewMasterProg
SeqC SubCall CallLab EOL
StartSub
ToolPath
SeqC EndSub EOL
CloseSub
SetFlagF('1') {not std sep sub Zreps in effect}
ELSE
ToolPath
END
END
SetDrillEndOpZ
SeqC DrillOff
IF Repeats?
EOL
FinishSubG92
SeqC
END
ZCP3
END
END
NextOp {loops back to EachOP until last Operation}

{End of program ************************************************************}

{finish last operation}
IF MultipleParts? AND OneToolAllParts? AND ExitClearancePlane?
EOL
CloseMP
SeqC
END
CoolOff EOL
IF MultipleParts? AND OneToolAllParts? AND FullUp?
SeqC OfstOff EOL
DoEndOpPS
CloseMP
SeqC SpinOff EOL
SeqC 'M19' EOL
ELSE
SeqC SpinOff EOL
SeqC OfstOff 'M19' EOL
DoEndOpPS
END
SeqC
IF FIRST ToolChangeAtHome? {.71.2 added FIRST modifier}
Rapid FirstHome
END
IF ToolOver?('1')
ToolChng
END
EOL
IF ProgStop?
SeqC 'M0' EOL
END
IF MultipleParts? AND AllToolsOnePart?
CloseMP
END
SeqC EOP EOL
CloseSub
Post2 {organize Subs into one program}
EOR EOL
Close
IF UseComments?
SetScale('1') {restore scale for comments}
Reopen
IF FileBytesComment?
'( FILE LENGTH- ' FileBytes# ' CHARACTERS )' EOL
END
IF FileFeetComment?
'( FILE LENGTH- ' FileFeet# ' FEET )' EOL
END
IF FileMetersComment?
'( FILE LENGTH- ' FileMeters# ' METERS )' EOL
END
Close
END