69

69



CYLINDER HEAD

.Assembly


Inspection (Cont’d)


KV10109500 (    -    )

and KV10107500 (    -    )

14.8 - 15.2 mm (0.583 • 0.598 in)


VALVE DIMENSIONS

Check dimensions in each valve. For dimensions, refer to S.D.S.

When valve head has been worn down to 0.5 mm (0.020 in) in margin thickness, replace the valve. Grinding allowance for valve stem end surface is

0.2 mm (0.008 in) or less.

T (Margin thickness)

SEMI 88

VALVE SPRING SOUARENESS

W

Out of square: Less than 2.0 mm (0.079 in)

Oi/tUfi TlAHcYiAO

1. Install valve oil seal.

S6M994

2.    Install valve component parts.

3.    Install camshaft oil seal.

4.    Apply a light coat of engine oil to camshaft, then install it.

When No. 1 cylinder is set at T.D.C. on its com-pression stroke, the camshaft front face is shown below.

Knock pin

SEM99:


•^1 -yrgr-. o O

.    {Ti


Camshaft end play 0.03 - 0.31 mm (0.0012 -0.0122 in)

Limit: 0.15 mn (0.059 ir


FREE LENGTH AND TENSION

Refer to S.D.S.

bri -:    f

"O*'.'/ 3

5. Measure camshaft end play with thermosta housing and gasket installed.

SEMOi:


Wyszukiwarka

Podobne podstrony:
CYLINDER HEAD InspectionDisassembly (Cont d) 6. Remove va!ve component parts. 4.
CYLINDER HEAD 4Inspection (Cont d) Replacement Replace valve or valve guide. 1. Heat cylinder head t
CYLINDER HEAD InstallationAssembly (Cont d) --:l 6. Install rocker shaft with rocker arms. Oil pump
CYLINDER HEAD-Installation (Cont d)- 2.    Install cylinder head with new gasket. a.
Suzuki RM250 8 19-22 SERYICE DATASPARE PARTS ITEM PART NAME PARTNUMBER QTY 1 O-RING, CYLINDER HEA
kolejność dokręcania śrób głowicy chrysler voyager Im porta nt notę Cylinder head bolts Tighten bolt
78685 Suzuki RM250T CYLINDER. CYLINDER HEAD AND PISTON 4-9 ♦    Install new O-rings @
41796 Suzuki RM1258 PERIODIC MAINTENANCE 2-23TIGHTENING TOROUE PART Nm kgf-m Ib-ft Cylinder head
CYLINDER HEAD VALVE INSERTS Check valve inserts for any evidence of pitting at valve contact surface
75 1acd287192 EMOiME DISASSEMBIYENGINE DSSASSEMBLY CYLINDER HEAD, CYLINDER AND PISTON NOTĘ: ________
suzuki rm25013 SERVICE DATA 19-7TIGHTENING TOROUEENGINE PART N-m kgf-m Ib-ft Cylinder head
89 TransAlp Manual Cylinder Head Valve 9 0 CYLINDER HEAD/VALVE 10 N-m (1.0 kg-m. 7 ft-łbl 10 N-m (1.
89 TransAlp Manual Cylinder Head Valve 9 1 9. CYLINDER HEAD/VALVE SERVICE INFORMATION 9-1 CYLINDER
89 TransAlp Manual Cylinder Head Valve 9 Valve guide reamer JCYLINDER HEAD/VALVE Measure and record
89 TransAlp Manual Cylinder Head Valve 9 CYLINDER HEAD/VALVE TOOLS: Valve guide drłver IN:  &n
89 TransAlp Manual Cylinder Head Valve 9 CYLINDER HEAD/VALVE Remove and inspect each valve.CAUTION
89 TransAlp Manual Cylinder Head Valve 9 CYLINDER HEAD/VALVE Use a 60 degree cutter to remove the b

więcej podobnych podstron