0 38 The servo lag of a moving axis is greater than the value given in machine parameter MP1720 (in lag mode) or MP1420 (in feedforward mode). \n 1 39 An excessively high nominal speed value was calculated. Analog axes: maximum nominal speed value +-10 V Analog spindle: maximum nominal speed value +-10 V Digital axes and spindle: maximum nominal speed value = maximum motor speed \n 2 41 The position deviation at a standstill is greater than the value entered in machine parameter MP1110.x. \n 3 42 During offset adjustment (with code number or cyclic) an offset voltage of more than 100 mV was determined. \n 4 50 In the TCH PROBE 0 (ISO: G55) cycle or during use of the manual probe cycles no touch point was reached within the traverse defined in machine parameter MP6130. \n 5 51 The servo lag of a moving axis is greater than the value given in machine parameter MP1710 (in lag mode) or MP 1410 (feedforward mode). \n 6 52 The stylus is already deflected at the start of a probing movement. \n 7 53 The battery in the touch probe is dead. \n 8 54 - Touch probe is not connected. - Battery in touch probe is dead. - No connection between infrared probe system and receiver unit. \n 9 55 The calculated tool path exceeds the machine's positive traverse limits. Positive traverse range is defined with MP650.x. \n 10 56 The calculated path of the tool exceeds the traversing range (software limit switch) of the machine. \n 11 57 The calculated tool path exceeds the machine's traverse limits. Negative traverse range is defined with MP670.x. \n 12 58 The calculated path of the tool exceeds the traversing range (software limit switch) of the machine. \n 13 59 Forced error through function FN14 (ISO: D14). With this function the TNC calls the preprogrammed messages of the machine manufacturer (e.g. from an OEM cycle). If during a program run or test run the TNC comes to a block with FN14 (D14), it stops operation and displays a message. You must then restart the program. \n 14 60 The NC block TOOL DEF (ISO: G99), is used more than once to define a tool using the same tool number in programs that are nested to each other. \n 15 61 The tool file (TOOL.T) cannot be edited while the TNC is executing a tool call. Pressing the EDIT ON/OFF soft key provokes this error message. \n 16 62 During a reference run on an encoder with distance-coded reference marks a distance of more than 1000 grating periodswas covered without passing over a reference mark. \n 17 63 - Electronic handwheel is not connected. - Incorrect handwheel selected in machine parameter MP7640. - Transmission line is defective or incorrect. \n 18 109 PLC runtime error: - You attempted to nest more than 32 module calls within each other. - You programmed a recursive module call that exceeds the limit of 32 levels. \n 19 110 PLC runtime error: You attempted to retrieve data from the stack, although it had not been written there. \n 20 111 PLC runtime error: You attempted to write more than 128 bytes of data to the stack. Word operands (B/W/D/K) each occupy 4 bytes, Logic operands (M/I/O/T/C) occupy 2 bytes. \n 21 112 PLC runtime error: - The processing of the cyclically executed program section takes too long. Check the subprogram structure for very calculation-intensive sections that you can start as SUBMIT jobs. - The displayed processing time will be increased during data transfer and in handwheel mode. In case of doubt, select handwheel mode and simultaneously start the data transfer at max. baud rate. At the same time, check "MAXIMUM PROCESSING TIME" in the PLC programming. Values should not exceed 150% (safety reserve in the event of unfavorable operating conditions!). \n 22 113 PLC runtime error: The operand for the CASE command contains a value that cannot be interpreted as offset in the CM table (smaller than 0, or greater than or equal to the table length). \n 23 115 PLC runtime error: - The address for a writing access to data types B/W/D/M/I/O/T/C is, through the inclusion of the index register, in an invalid region for these operand types. - The index register contains a value, due to accessing a constant field, which is not possible for this field (less than 0, or greater than or equal to field length). - The address of a string leads through the inclusion of the index register to an invalid value. - The number of a dialog (S#Dn[X]) or an error message (S#En[X]) leads through the inclusion of the index register to an invalid value (less than 0 or greater than 999). - During the addressing of a component string. \n 24 133 PLC runtime error: More than one of the markers M4005 (M03), M4006, (M04), M4007 (M05) is set. \n 25 134 PLC runtime error: More than one of the functions "PLC positioning," "datum shift," or "spindle orientation" has been activated. \n 26 151 Machine parameter input error: A line was found without a machine parameter number (not an empty line or comment). \n 27 152 Machine parameter input error: The given machine parameter does not exist (incorrect number). \n 28 153 Machine parameter input error: No separator (":")was found between the number and value of the machine parameter. \n 29 154 Machine parameter input error: The input value for the machine parameter is incorrect. \n 30 155 Machine paremeter input error: A machine parameter has been defined twice. \n 31 156 Machine parameter input error: A machine parameter is not defined. The line is generated automatically. \n 32 157 Machine parameter input error: Machine parameter cannot be saved. \n 33 159 You attempted to assign a tool to a locked pocket in the tool-pocket table. \n 34 160 - The input value of the pocket number in the tool table is greater than machine parameter MP7261. - MP7261 = 0, pocket output is activated through MP7480 and no pocket has been assigned to the called tool. \n 35 937 - The input value for the pocket number in the tool table is greater than machine parameter MP7261. - MP7261 = 0, pocket output is activated through MP7480, and the called tool is not assigned to a pocket. \n 36 161 You did not program a feed rate. \n 37 162 In a tool call a programmed rotation is active and at the same time the new tool axis is not the same as or parallel to the previous tool axis. \n 38 163 The service life of the called tool has expired and you have not defined a replacement tool. \n 39 164 The voltage of the buffer battery in the power supply unit is too low. \n 40 165 You attempted to call either the Rigid Tapping cyle or the Tapping cycle, although your machine does not have a controlled analog spindle \n 41 166 There are several tool tables in the NC memory and no table is activated in the Test Run operating mode. \n 42 167 A datum table is required to machine a part program. Either there is no table in the control's NC memory, or several tables have be saved and none activated. \n 43 168 This message indicates that there is an error message on the screen now in the background. \n 44 938 In this context the key has no function. \n 45 939 The NC program memory no longer suffices for part programs. \n 46 940 In the NC program the original search address no longer exists. \n 47 941 A tool definition with the number "0" is not permitted. \n 48 169 You attempted to give a tool more than one definition. \n 49 170 In a LBL CALL (ISO: L 0,0) block of a part program or in a jump instruction (parametric calculation) you attempted to program a jump to the label 0. \n 50 942 - The value you entered is out-of-range. - Cycle 209 (ISO: 209): You entered the value 0 as infeed depth for chip breaking (Q257). \n 51 943 You pressed a sequence of keys so quickly that you filled up the keyboard buffer. \n 52 171 In an APPR or DEP block in a part program the use of a Q parameter leads to an illegal intermediate result: The length of the tangential line for approaching or departing the contour becomes negative. \n 53 172 In an APPR or DEP block of a part program the use of a Q parameter leads to an illegal intermediate result: The center angle of the tangential arc for approaching or departing the contour becomes negative. \n 54 173 In a Contour Train cycle the use of a Q parameter leads to an illegal intermediate result: The length of the tangential line segment for approaching or departing the contour becomes negative. \n 55 174 In a Contour Train cycle the use of a Q parameter leads to an illegal intermediate result: The center angle of the tangential arc for approaching and departing the contour becomes negative. \n 56 175 You have entered a negative value as tolerance for the automatic insertion of a rounding arc (M function M112). \n 57 176 In the programmed positioning of a rotary axis with feed rate in mm/min (M116) an excessively high velocity results for the rotary table. \n 58 177 - In the execution of a Cylindrical Surface cycle the entered milling depth is greater or equal to the radius of the cylindrical surface. - The ratio of the unit radius to the machining radius is too large. \n 59 178 In the execution of a Cylinder Surface cycle the programmed radius of the cylinder surface is less than or equal to 0. \n 60 179 In the superimposition of a handwheel movement (M function M118) the programmed maximum permissible superimposition is less than 0. \n 61 180 Error in the conversion of the programmed workpiece blank in the graphic: - The programmed spindle axis was not X, Y or Z. - An edge length is negative (the minimum and limits were switched). - One edge length is smaller than 0.1 mm. - The length of the shortest edge is less than approx. 1% of the longest edge. \n 63 182 The PLC input for the control-is-ready signal is inactive. On the safety-oriented controls: The PLC input "NE1" is inactive. During the cutout-channel test, the level of the "NE1" and "NE2" input is not identical with that of the "T1" and "T2" safety output. \n 64 183 After an interruption of the program run the TNC can no longer resume the program run from the cursor's present location. \n 65 184 You attempted to call a program that is not stored in TNC memory. \n 66 185 The TNC cannot save any more files. \n 67 944 This file name already exists. \n 68 187 You attempted to program the same label number in several LBL SET (ISO: G98 Lxx) blocks in a part program. \n 69 188 During a program start or a subprogram call, several LBL SET (ISO: G98 Lxx) blocks in a part program were found \n 70 189 E During data transfer with BCC the signal was received 15 times in succession. A to H Error code of the receiver module with one w/o E of the following causes: - The baud rate settings of the TNC and peripheral device do not match. - The parity bit is erroneous. - Erroneous data frame (e.g.: no stop-bit). - The receiver module of the interface is defective. K During transmission of an error to the TNC the <1> character was not transmitted after the character. L After the error sequence <1> an incorrect error number was received (error numbers 0 to 7 are permitted). M During data transmission with BCC the character was transmitted 15 times in succession. N An expected acknowledgment or was not transmitted after a certain time. \n 71 194 Data transmission was interrupted with the key. \n 72 196 You attempted to assign an already occupied data interface. \n 73 197 The baud rates set at the two data interfaces do not permit simultaneous transmission over both interfaces. \n 74 945 This is a general error messsage showing that there is some error in the program data (e.g. an ERROR block). \n 75 946 An error occurred during downloading through the data interface. The TNC marks the erroneous block with ERROR. \n 76 200 - The interface is not connected. - The external device is either switched off or not ready. - The transmission cable is defective or incorrect. \n 77 201 After the control was switched on, a file in NC memory was found faulty and deleted. \n 78 947 The machine parameters have been erased and the PLC program is missing. \n 79 948 You cannot edit or erase this program until the protection has been removed. \n 80 202 - During start-up of a subprogram the control found that the calling program had been changed. - During a return jump from a subprogram the control found that the calling program had been changed. \n 81 203 The internal or external EMERGENCY STOP circuit is found by the system CPU to be defective. \n 82 205 Error message from the PLC (see machine documentation). \n 83 207 During execution of a blockwise transferred part program (DNC mode) the control found that a called subprogram does not exist in NC memory. \n 84 209 You edited the machine or user parameter list and tried to exit the editor with END. This is not permitted if the part program or a PLC positioning operation is running. \n 85 212 You attempted in an FK program to delete a block to which another part of the program makes a reference. \n 86 214 Internal calculations have resulted in a non-representable numerical value. \n 87 215 Internal calculations have resulted in a non-representable numerical value. \n 88 216 The TNC attempted to display a Q parameter whose value lies outside the permissible range of -99 999.9999 to +99 999.9999. \n 89 217 Calculation of a coordinate from a Q parameter resulted in a value outside the permissible range of -99 999.9999 to +99 999.9999. \n 90 218 - Calculation of a spindle speed from a Q parameter resulted in a value outside the permissible range of 0 to +99 999.9999. - A speed limit was defined for the active tool in the tool table (NMAX column). \n 91 219 Calculation of a feed rate from a Q parameter resulted in a value outside the permissible range of 0 to 300 000. \n 92 220 - Calculation of a tool number from a Q parameter resulted in a value outside the permissible range of 0 to 32767. - You have called a tool number that is greater than the number of tools defined in the tool table. \n 93 221 Calculation of a label number from a Q parameter resulted in a value outside the permissible range of 1 to 255. \n 94 222 Calculation of an error number for the FN14 function (ISO: D14) from a Q parameter resulted in a value outside the permissible range of 0 to 499. \n 95 223 Calculation of a scaling factor from a Q parameter resulted in a value outside the permissible range of 0.0001 to +100.007936. \n 96 224 In an NC block you have programmed an incremental polar angle (IPA, ISO: G91 H..) greater than or equal to 5760 degrees (16 full circles). \n 97 225 You have programmed a thread pitch of 0 in the Rigid Tapping cycle or Tapping cycle. \n 98 226 Error in internal calculation, e.g. due to: - Division by 0 - Extracting the root of a negative value. \n 99 227 Calculation of an APPR or DEP block in a part program resulted in an arithmetic error. \n 100 228 Calculation of an APPR or DEP block in a part program resulted in an arithmetical error. \n 101 229 Calculation of an APPR or DEP block in a part program resulted in an arithmetical error. \n 102 230 Calculation of an APPR or DEP block before or after a helix resulted in an arithmetical error. \n 103 231 Calculation of a rounding circle for contour-parallel rough-out resulted in an arithmetical error. \n 104 232 Calculation of the circle center of a "circle with radius" block in a contour pocket resulted in an arithmetical error. \n 105 233 Calculation of a "circle with tangent" block in a contour pocket resulted in an arithmetical error. \n 106 234 Calculation of a rounding circle or chamfer in a contour pocket resulted in an arithmetical error. \n 107 235 Calculation of the intersection of two arcs in the contour pocket resulted in an arithmetical error. \n 108 236 Calculation of the intersection of an arc with a line in a contour pocket resulted in an arithmetical error. \n 109 237 Calculation of the intersection of two lines in the contour pocket resulted in an arithmetical error. \n 110 238 Calculation of the approaching or departing path with APPR LCT or DEP LCT in the Contour Train cycle resulted in an arithmetical error. \n 111 239 Calculation of the radius compensation in the Contour Train cycle resulted in an arithmetical error. \n 112 240 Calculation of the intersection of the contour with the tool path in the contour pocket resulted in an arithmetical error. \n 113 241 The length of the path to be traversed in the contour pocket or in the Contour Train cycle is too large to be represented as a number. \n 114 242 Calculation of the contour-parallel paths for clearing out a contour pocket resulted in an arithmetic error. \n 115 243 Calculation of the contour elements of a contour pocket resulted in an arithmetical error. \n 116 244 Calculation of the radius compensation of a contour resulted in a mathematical error. \n 117 245 Calculation of the radius compensation of a contour resulted in a mathematical error. \n 118 246 Calculation of the normal from a given point on a contour element for contour-parallel rough-out resulted in an arithmetical error. \n 119 247 Calculation of the intersections in the contour pocket resulted in an arithmetical error. \n 120 250 Calculation of automatically inserted rounding arcs (M function M112) resulted in an arithmetical error. \n 121 251 Calculation of an arithmetical expression in the Q parameter calculation resulted in an arithmetical error. \n 122 252 Checking the software limit switch resulted in an arithmetical error. \n 123 253 You tried to cancel the tool radius compensation with R0 (ISO: G40) in an arc block. \n 124 254 You attempted to program a chamfer before starting the tool radius compensation. \n 125 255 You attempted to program a corner radius before starting the tool radius compensation. \n 126 256 You tried to activate the tool radius compensation with RL or RR (ISO: G41 or G42) in an arc block. \n 127 257 You attempted to program a corner radius between an part program block without radius compensation and a line block with tool radius compensation. \n 128 258 You attempted to take over a pole (or circle center) after the first block with tool radius compensation (empty CC block, ISO: G29). \n 129 259 You attempted to program an APPR block during an active radius compensation. \n 130 260 - You deleted part of a cycle. - You have inserted other part program blocks within a cycle. \n 131 261 - You have programmed a cycle call without first having defined a fixed cycle. - You attempted to call a cycle that automatically becomes effective upon definition. \n 132 263 You programmed the plunging depth 0 in the definition of the called fixed cycle. \n 133 264 You attempted to call a user parameter that is not stored in TNC memory. \n 134 265 You defined a subprogram number in Cycle 14 Contour Geometry (ISO: G37) that does not exist in your program. \n 135 266 You called a user cycle or a subprogram in the definition of a contour, a contour pocket or a cycle contour train. However, the corresponding file could not be opened for reading. \n 136 272 A part program block contains a syntax error. \n 137 274 You programmed a tool definition (TOOL DEF, ISO: G99), although the central tool file is active. \n 138 275 The definition of a tool (TOOL DEF, ISO: G99) is missing the value for tool length or tool radius. \n 139 276 You programmed a tangentially connecting circle (CT) immediately after an APPR block. \n 140 277 You programmed a chamfer (CHF) immediately after an APPR block. \n 141 278 You programmed a rounding radius (RND) immediately after an APPR block. \n 142 279 You programmed a rounding arc (RND, ISO: G25) with the radius 0 in the definition of a contour, a contour pocket or a contour train. \n 143 280 You programmed a chamfer (CHF, DIN/ISO: G24) with the length 0 in the definition of a contour, a contour pocket or a contour train. \n 144 281 You programmed two rounding arcs (RND, ISO: G25) in succession in the definition of a contour, a contour pocket or a contour train. \n 145 282 You programmed a rounding arc (RND, ISO: G25) immediately after a chamfer (CHF, ISO: G24) in the definition of a contour, a contour pocket or a contour train. \n 146 283 You programmed a chamfer (CHF, ISO: G24) immediately after a rounding arc (RND, ISO: G25) in the definition of a contour, a contour pocket or a contour train. \n 147 284 You programmed two chamfers (CHF, ISO: G24) in immediate succession in the definition of a contour, a contour pocket or a contour train. \n 148 285 You programmed a DEP LCT block for departing a contour immediately after a helix. \n 149 286 You programmed the APPR LCT block or APPR PLCT block for approaching a contour immediately before a helix. \n 150 287 You programmed one of the following (non-permissible) blocks within the definition of a contour, a contour pocket or a contour train: - TCH PROBE (ISO: G55) - TOOL DEF (ISO: G99) - TOOL CALL (ISO: T..) - BEGIN PGM (ISO: %..) \n 151 288 You programmed a rounding radius immediately before a CT (ISO: G6) or CTP (ISO: G16) block in the definition of a contour, a contour pocket or a contour train. \n 152 289 You programmed a rounding arc (RND, ISO: G25) as first block in the definition of a contour, contour pocket or contour train. \n 153 290 You programmed a chamfer (CHF, ISO: G24) as first block in the definition of a contour, contour pocket or contour train. \n 154 291 You programmed a DEP block in a position other than last in the definition of a contour or contour train. \n 155 292 You programmed a rounding arc (RND, ISO: G25) as last block in the definition of a contour, contour pocket or contour train. \n 156 293 You programmed a chamfer (CHF, ISO: G24) as last block in the definition of a contour, contour pocket or contour train. \n 157 294 You programmed more than one DEP block in the definition of a contour or a contour train. \n 158 295 You programmed a DEP block in the definition of a contour or contour pocket. \n 159 296 You programmed an APPR block in the definition of a contour or a contour pocket. \n 160 297 You programmed an APPR block in a position other than first in the definition of a contour or contour train. \n 161 299 - During compilation of an FK program a part program "ERROR" block was read-in. - You defined a Cycle 14 in a contour subprogram (ISO: G37). \n 162 300 You attempted to execute an automatic tool call while a part program block with radius compensation was running. \n 163 302 You have programmed a positioning operation with M91 or M92 with a tilted working plane. \n 164 303 You attempted to activate the Tilted Working Plane functions and M114 simultaneously. \n 165 305 You programmed the M function M114 in a block with tool radius compensation. \n 166 307 In the Contour Lines cycle (TCH PROBE 7) you programmed the starting position in one axis twice. \n 167 308 You programmed an axis twice in a single positioning block. \n 168 309 You programmed an axis twice in the Mirror Image cycle. \n 169 310 You called a Slot Milling or Rectangular Pocket cycle in which the same axis is programmed for length and width. \n 170 311 While defining Cycle 26 (axis-specific scaling factor) you programmed the scaling factor or the scaling datum twice in one axis. \n 171 313 The two axes of the circle end point in a circle block (C, ISO: G2, G3, G12, G13)) differ from the axes in the circle center block (CC, ISO: I,J,K). \n 172 314 LN block: Calculation of the plane direction resulted in an error. \n 173 315 The tool axis is not perpendicular to the plane in which the basic rotation is active. \n 174 317 In a circular block you programmed the coordinates for the end point in a principal axis and its associated parallel axis. \n 175 318 You programmed only one axis in a "circle with radius" block (CR, ISO: G2,G3 with R). You also either did not define a tool axis or the programmed axis is the tool axis. \n 176 319 In a CT block (ISO: G6, G16) you defined an axis that is not included in the working plane. \n 177 320 Radius compensation in a circle block is not possible if the circle lies in a plane parallel to the tool axis and a basic rotation or a programmed rotation is active. \n 178 321 Radius compensation is not possible in a circle block (C, ISO: G2, G3) if the starting point and end point do not have the same two axes or those axes are not parallel to the axes of the circle center (CC, ISO: I,J;K). \n 179 322 Radius compensation is not possible in a rounding block (RND, ISO: G25) if two mutually parallel linear axes are programmed in the preceding positioning block (e.g. X and U). \n 180 323 Radius compensation is not possible in a chamfer block (CHF, ISO: G24) if two mutually parallel linear axes are programmed in the preceding positioning block (e.g. X und U). \n 181 324 You programmed a radius-compensated circle block that does not lie in the compensation plane. \n 182 325 You programmed only one axis in a circle center or pole block (CC, ISO: I,J,K) and that axis does not lie in the plane that was previously defined in a CC block, or there is no preceding CC block. \n 183 326 You programmed a circle center block or pole takover block (CC,ISO: I,J,K) without entering coordinates (pole assumption) and without explicitly programming two linear axes in the preceding positioning block. \n 184 327 The calculated positioning operation requires movement in more than five axes. \n 185 328 You programmed a helix for which the axis of linear motion is identical or parallel to one of the axes of circular motion. \n 186 329 You programmed a rotary axis as tool axis. \n 187 950 An incorrect axis is programmed in the highlighted block. \n 188 951 An incorrect axis is programmed in the highlighted block. \n 189 330 - You programmed a locked axis in a part program block. - A traverse was calculated for a locked axis (e.g. due to an active rotation). - A programmed axis is a freely traversing rotary axis. \n 190 331 You called a Slot Milling cycle or Pocket Milling cycle in which the programmed axes for length and width do not lie in the working plane. \n 191 332 You called a Slot Milling cycle or Pocket Milling cycle in which one of the programmed axes for length or width is a rotary axis. \n 192 333 You called a Slot Milling cycle or Pocket Milling cycle in which one of the programmed axes for length or width is a secondary axis, although a programmed rotation or basic rotation is active. \n 193 335 In Cycle 27 (Cylinder Surface, ISO: G127) you did not program the rotary axis corresponding to the linear axis in the first block of the description of a contour. \n 194 337 The axis recognized as main axis in Cycle 27 (Cylinder Surface, ISO: G127) is not a rotary axis. \n 195 338 The linear axis programmed in Cycle 27 (Cylinder Surface, ISO: G127) or the tool axis selected for machining is none of the axes X, Y or Z. \n 196 339 You programmed the slave axis of a gantry axis in a part program block. \n 197 952 You entered an invalid spindle speed. \n 198 340 The spindle speed that you programmed is greater than the maximum spindle speed as defined in machine parameter MP3020. \n 199 341 The spindle speed that you programmed is less than the minimum spindle speed as defined in machine parameter MP3020. \n 200 342 The spindle speed that you programmed is greater than the maximum speed for the analog spindle as defined in machine parameter MP3515. \n 201 343 The spindle speed that you programmed results in an excessively low analog voltage (MP3240.1). \n 202 344 The programmed spindle speed results in an excessively high feed rate in the tool axis during execution of a Rigid Tapping cycle or Tapping cycle. \n 203 345 You called a Rigid Tapping or Tapping cycle with a programmed spindle speed of 0. \n 204 346 The programmed spindle speed does not lie in the pattern of spindle speed ranges defined in machine parameter MP3020. \n 205 347 In the definition of a contour, contour pocket or contour train you programmed a chamfer between two contour elements of which one is an arc. \n 206 348 The positioning block preceding a chamfer block (CHF, ISO: G24) is not a straight line. \n 207 349 The positioning block following a chamfer block (CHF, ISO: G24) is not a straight line. \n 208 350 You programmed in sequence a positioning block without radius compensation, a positioning block with radius compensation, and a chamfer (CHF, ISO: G24). \n 209 351 You programmed in sequence a positioning block without radius compensation, a chamfer (CHF, ISO: G24), and a positioning block with radius compensation. \n 210 352 You programmed in sequence a positioning block with radius compensation, a chamfer (CHF, ISO: G24), and a positioning block without radius compensation. \n 211 353 You programmed a chamfer (CHF, ISO: G24) in a plane perpendicular to the working plane followed by a movement only in the tool axis. \n 212 354 You programmed a chamfer (CHF, ISO: G24) that cannot be inserted because the preceding line is too short. \n 213 355 You programmed a chamfer that (CHF, ISO: G24) cannot be inserted because the subsequent line is too short. \n 214 356 While defining a contour, contour pocket or contour train you programmed a chamfer (CHF, ISO: G24) whose starting and end points no longer lie on one of the adjoining contour elements. \n 215 357 The difference between the radius at the end point of a C block (ISO: G2, G3) and the radius at the starting point exceeds the tolerance defined in machine parameter MP7431. \n 216 358 The difference between the radius at the end point of a C block (ISO: G2, G3) and the radius at the starting point exceeds the tolerance defined in machine parameter MP7431. \n 217 359 The distance between the circle starting point and the circle end point in the CR block (ISO: G2, G3 mit R) is less than 0.2 µm. \n 218 360 You programmed a "circle with radius" block (CR, ISO: G2, G3 with R) such that the distance between the starting point and the end point is greater than the diameter. \n 219 361 After an interruption in a circle block a program run was restarted although the starting position deviates from the arc by a distance greater than the tolerance defined in machine parameter MP7431. This can happen, for example, after you move an axis in a manual mode. \n 220 362 In Cycle 14 (Contour Geometry, ISO: G37) you defined a subprogram number that does not exit. \n 221 363 A contour subprogram defined in Cycle 14 (Contour Geometry, ISO: G37) is not concluded with LBL 0 (ISO: G98). \n 222 364 You attempted to used LBL CALL (ISO: L x,x) to call a subprogram or a program section repeat that does not exist. \n 223 365 In the Contour Geometry cycle you have listed a subprogram number that does not exist. \n 224 366 You tried to move with polar coordinates (LP/CP/CTP, DIN/ISO: G10/G11/G12/G13/G15/G16), without first programming a pole (CC) (ISO: I/J/K). \n 225 367 You programmed a circle block (C, ISO: G2/G3) without first defining a circle center (CC, ISO: I/J/K). \n 226 368 - Cycle 3 (slot): You defined a width greater than four times the tool radius. - Cycle 253 (slot) or Cycle 254 (circular slot): The slot width for roughing (Q219 - Q368) is greater than four times the tool radius. - Cycle 240: You entered a centering diameter greater than the tool diameter. - Cycle 210 (slot) or Cycle 211 (circular slot): The slot width is six times greater than the tool radius. \n 227 369 You called the Slot Milling, Pocket Milling, Circular Pocket Milling, or Contour Pocket cycle although the active tool has a radius of 0. \n 228 370 You programmed a radius-compensated single-axis positioning block which without the radius compensation does not result in tool movement (e.g. IX+0 R+, ISO: G7). \n 229 371 You programmed a radius-compensated single-axis positioning block whose path would take a direction opposite to that of the non-compensated path. \n 230 372 You attempted to run a part program block with tool radius compensation after inserting a spherical or toroidal cutter. \n 231 373 - In the definition of a contour, a contour pocket or a contour train you neglected to program radius compensation - You called one of the slot cycles 210 or 211 with tool radius 0 \n 232 374 You called Cycle 22 (Contour-Parallel Roughing, ISO: G122) or Cycle 21 (Pilot Drilling, ISO: G121) although the product of the tool radius and the overlap factor is 0. \n 233 375 In an NC block, you tried to move an axis that had not yet completed a reference run. \n 234 376 You programmed in sequence a positioning block without radius compensation, a rounding arc (RND, ISO: G25), and a circle block with radius compensation. \n 235 377 You programmed a corner radius perpendicular to the working plane, followed only by a movement in the tool axis. \n 236 378 In the positioning block before a rounding arc (RND, ISO: G25) either you programmed a movement only in the tool axis or you used the M function M98 to cancel compensation. \n 237 379 While defining a contour of a contour pocket or of a contour train you programmed a rounding arc (RND, ISO: G25) with so large a radius that it does not fit between the adjoining elements. \n 238 380 In a rounding block approaching a contour, the starting point of the block lies inside the circle of the arc. \n 239 381 In a rounding block approaching a contour the starting point of the block lies too close to the center of the rounding circle (less than 1.6 µm). \n 240 382 In a rounding block departing a contour, the end point of the departing block lies within the rounding circle. \n 241 383 In a rounding block departing a contour, the end point of the departing block lies too close to the center of the rounding circle (less than 1.6 µm). \n 242 384 You programmed a rounding arc (RND) whose starting point does not lie on the contour or on the compensated contour. \n 243 385 You programmed a rounding arc (RND), whose end point does not lie on the contour or on the compensated contour. \n 244 386 You defined a pocket (Cycle 4) in which the sum of twice the corner radius plus the stepover factor is greater than the width of the pocket. \n 245 387 In the Contour Train cycle, you programmed the approach to or departure from a contour with a rounding block whose starting position or target position lies within the arc. \n 246 388 You called a fixed cycle without first switching on the spindle. \n 247 389 You ran a TOOL CALL block (ISO: T..) in which a mirrored axis is given as tool axis. \n 248 390 In Cycle 8 (Mirror Image, ISO: G28) you defined the tool axis as a mirrored axis. \n 249 391 You programmed a positioning block with tool radius compensation without first calling a tool. \n 250 392 You programmed a paraxial positioning block with tool radius compensation without first calling a tool. \n 251 393 You called a fixed cycle without first activating a tool. \n 252 394 You programmed Cycle 10 (Rotation,ISO: G73) without first calling a tool. The tool call defines which working plane the TNC rotates. \n 253 395 You attempted to approach a position using the positioning logic, but did not first define the working plain through a tool call. \n 254 396 You programmed the M function for reducing the feed rate in the tool axis, but did not call a tool first. \n 255 397 You called the TCH PROBE 0 cycle (ISO: G55) without first calling a tool. \n 256 398 In a TOOL CALL (ISO: T..) you entered a tool number for which there is no definition in the program. \n 257 400 You programmed a TOOL CALL (ISO: T..) with a tool number that does not exist in the central tool file (TOOL.T). \n 258 401 You programmed a tool axis in the TOOL CALL block (ISO: T..), but no tool number. \n 259 402 - Contour milling: The radius of an arc block at an inside corner is smaller than the tool radius. - Thread milling: The thread core diameter is smaller than the tool diameter. - Slot milling: The slot width for roughing is smaller than the tool diameter. - Cycle 251, rectangular pocket: The rounding radius Q220 is smaller than the tool radius. - Cycle 214: The given workpiece-blank diameter is smaller than the tool diameter \n 260 403 An inside radius compensation is not possible when the radius of the rounding arc is smaller than the cutter radius. \n 261 404 The compensated path of the straight line or of the circle would take a direction opposite to that of the non-compensated path. \n 262 405 On inside corners the resulting intermediate angle would be smaller than 0.028 degrees. \n 263 406 - Slot Milling cycle: The slot width is less than the tool diameter. - Cylinder Surface cycle: The slot width is less than the tool diameter. \n 264 407 Pocket Milling cycle: The pocket width is less than or equal to the tool diameter. \n 265 408 Pocket Milling cycle: The corner rounding radius is smaller than the cutter radius. \n 266 409 Circular Pocket Milling cycle: The pocket radius is smaller than the cutter radius. \n 267 410 In Cycle 24 (Side Finishing, ISO: G123) the sum of the finishing cutter radius and the finishing allowance is greater than or equal to the sum of the roughing cutter radius and the roughing allowance. \n 268 411 During Cycle 21 (Pilot Drilling for Contour-Parallel Rouch-Out, ISO: G121), the drilling tool radius is so large that it would gouge the workpiece. \n 269 412 The tip edge radius of the toroidal cutter is greater than its shaft radius. \n 270 413 Type of interpolation undefined. \n 271 414 Type of dimensions undefined. \n 272 415 A direction of rotation is required to start a circular movement. \n 273 416 The TNC cannot exactly calculate the geometry from the present position (e.g., the programmed coordinates of the first positioning block are the same as the compensated actual position). \n 274 417 Error after an interruption in program run (with change of operating mode or PLC positioning): A pole cannot be taken over if a CT block was programmed before the interruption. \n 275 418 Error after interruption in program run (with change of operating mode or PLC positioning): After an interruption you attempted to start the program with a cycle call or with the TOUCH PROBE measuring cycle. \n 276 419 - The first block in the part program is a block with automatic pole assumption (CC without coordinates, ISO: G29). - After a program interruption you pressed GOTO to select a block with automatic pole assumption. \n 277 420 - The first positioning block in the part program is a CT block (ISO: G6, G16). - After a program interruption you pressed GOTO to select a CT block (ISO: G6, G16). \n 278 421 - The first positioning block in the part program is an RND block (ISO: G25). - After a program interruption with you pressed GOTO to select an RND block (ISO: G25). \n 279 422 - The first positioning block in the part program is a CHF block (ISO: G24). - After an interruption with GOTO you selected a CHF block (ISO: G24). \n 280 423 After a program interruption with GOTO you attempted to select a departing block. \n 281 424 At the beginning of the program you activated a tilted working plane and M114 at the same time. \n 282 425 During resumption of a part program a tool radius compensation is active RL/RR (ISO: G41, G42) although a PLC datum shift must be executed. \n 283 426 When resuming a part program you selected a CT block (ISO: G6, G16) although a PLC positioning or a PLC datum shift must be executed. \n 284 953 Incorrect block format in the highlighted block. \n 285 427 The radius is missing for a Circle with Radius block (CR, ISO: G02, G03). \n 286 429 You nested more than 8 subprogram calls (CALL LBL xx, ISO: Lx,0). \n 287 430 You nested more than 10 program section repeats. \n 288 432 Internal stack error in an arithmetical expression (FN20, ISO: D20), e.g. due to excessive nesting. \n 289 433 The algebraic signs of the setup clearance, total hole depth and plunging depth do not match. \n 290 434 The programmed dwell time in the Dwell Time cycle, Peck Drilling cycle, or Tapping cycle is negative (through Q parameter). \n 291 435 In an LP/CP block (ISO: G10, G11, G12, G13) no polar angle or incremental polar angle is defined, i.e.: - The distance between the last programmed position and the pole is less than or equal to 0.1 µm. - No rotation is programmed between pole assumption and an LP/CP block. \n 292 436 You programmed a CT block (ISO: G6, G16; tool compensation active) that only activates the tool axis. \n 293 437 - You programmed a circular movement in which the radius is less than 1.6 µm. - In the thread milling cycle 263, 264 or 265 you entered 0 for the countersinking offset at front. \n 294 438 Contour Pocket or Contour Train cycle: The TNC cannot determine the starting point of the contour. \n 295 439 Contour Pocket or Contour Train cycle: The first or second block in the contour subprogram is a CT block (ISO: G6, G16). The direction of the CT block is therefore undetermined. \n 296 440 You interrupted the part program during a DEP block and then attempted to restart. \n 297 441 You interrupted the part program during a DEP block, then moved the axes, and then attempted to restart. \n 298 442 You did not give any coordinates in the NC block after APPR. \n 299 443 During digitizing the stylus went out of the defined digitizing range. \n 300 444 - Range cycle: MAX value is smaller than MIN value - Range extends past software limit switch - No Range cycle defined \n 301 445 Digitizing with contour lines: Incorrect starting position selected. \n 302 446 Digitizing with contour lines: Touch probe does not reach the starting point within the time set in the cycle. \n 303 447 For digitizing axes: - Probe point interval greater than 65 535 (with Q parameter) - Incorrect line-by-line digitizing axis \n 304 448 SL cycles II or milling cycles 25x: You have entered an allowance for floor greater than the milling depth. \n 305 449 - Rotation not permitted during digitizing. - Rotation not permitted during automatic measuring (measuring cycles 400 to 418) together with 3-D rotation. - 3-D rotation not permitted together with Cycle 247. \n 306 450 You programmed a scaling factor before the TCH PROBE 0 cycle (ISO: G55) or before the digitizing cycles. \n 307 451 You attempted to scale a circular contour element with differing axis-specific scaling factors. \n 308 452 You programmed a mirror image before the TCH PROBE 0 cycle (ISO: G55) or before the digitizing cycles. \n 309 453 Digitizing with contour lines: Datum shift is active. \n 310 454 Digitizing with measuring touch probe: Maximum permissible stylus deflection was exceeded. \n 311 455 Contour Pocket cycle: Internal calculations resulted in too many subcontours. \n 312 456 Contour intersects itself to produce too many subcontours. \n 313 457 The union of cycles results in to many subcontours. \n 314 458 Calculation of the tool path results in more than 12 subcontours. \n 315 459 Calculation of the equidistant results in too many subcontours. \n 316 460 Calculation of the equidistant results in too many subcontours. \n 317 461 A contour subprogram contains more than 128 geometrical elements. \n 318 462 A contour subprogram contains more than 128 geometrical elements. \n 319 463 The union of contours results in too many subcontours. \n 320 464 The union of contours results in too many subcontours. \n 321 465 Calculation of the equidistant results in too many subcontours. \n 322 466 Calculation of the equidistant results in too many subcontours. \n 323 467 Calculation of the equidistant results in too many subcontours. \n 324 468 Contour intersects itself to produce too many subcontours. \n 325 469 The union of contours results in too many subcontours. \n 326 470 Calculation of the equidistant results in too many subcontours. \n 327 471 The contour to be machined in contour-parallel roughing has too many subcontours. \n 328 472 Calculation of the equidistant results in too many subcontours. \n 329 473 Calculation of the equidistant results in too many subcontours. \n 330 474 While defining the range for a measuring touch probe you entered too many subcontours. \n 331 475 A contour starting point lies on a contour intersection: The TNC cannot recognize how you wish to combine the contours. \n 332 477 A contour subprogram contains only one point. \n 333 478 The TNC cannot determine the rotational direction of the programmed contour. \n 334 479 Programmed contour is not continuous. \n 335 480 Contour is too complex. \n 336 481 On a self-intersecting contour the starting point lies on an intersection. \n 337 482 At the starting point of the contour is an intersection that cannot be resolved by the TNC. \n 338 483 Incorrect input in MP810. \n 339 484 Contour cannot be resolved. \n 340 485 Contour cannot be resolved. \n 341 486 Contour cannot be resolved. \n 342 487 Contour cannot be resolved. \n 343 488 Contour cannot be resolved. \n 344 489 Contour cannot be resolved. \n 345 490 Contour cannot be resolved. \n 346 491 Contour cannot be resolved. \n 347 492 Contour cannot be resolved. \n 348 493 Contour cannot be resolved. \n 349 954 You used an address letter incorrectly in an ISO block. \n 350 494 Maximum block length exceeded. \n 351 955 In a part program block you use G codes from the same group (e.g. G01 and G02). \n 352 495 You programmed an unknown G function. \n 353 496 Block number N is missing in the NC block. \n 354 497 Error in compensation value conversion: In the *.CMA file either there is no active line selected or the selected line does not exist. \n 355 500 Error in compensation value conversion: Permissible number of compensation points exceeded. \n 356 501 Error in compensation value conversion: Permissible number of compensation functions exceeded. \n 515 957 The TNC was restarted after a power interruption. \n 518 958 Error message after power interruption. \n 636 859 General indication of a previous error in the graphic simulation. \n 637 860 Simulation of a movement in the axes A, B, C, U, V, or W is not possible in the graphic. \n 638 861 The selected section cannot reduced any further. \n 639 862 The selected section cannot be enlarge any further. \n 640 863 The workpiece blank cannot be displayed: - The workpiece blank is not completely defined. - One edge has a negative length. - The longest edge is too large or too small. - Ratio of edge lengths is excessive. \n 641 864 - The tool axis entered in a tool call does not match the tool axis entered in the BLK FORM block (ISO: G30/G31). - Programming graphics: In an APPR or DEP block you have programmed coordinates that do not lie in the drawing plane. The drawing plane is perpendicular to the tool axis, which is indicated in the BLK FORM. If no BLK FORM has been programmed, the drawing plane lies in the X/Y. \n 642 865 The radius of the active tool cannot be displayed. \n 656 888 The ASCII editor could not find the desired text in a file. \n 692 1086 Automatic establishment of points for the digitizing range in the Positioning with Manual Data Input operating mode: Number of stored points (max. 893) exceeded. \n 694 1097 Geometry error message: The tolerance value entered with M124 is greater than half the tolerance value in M112. \n 699 1106 Warning before deleting an entire HEIDENHAIN cycle. \n 700 1107 HEIDENHAIN cycles usually consist of several component blocks. You have attempted to write another part program block in between these component blocks. \n 711 1125 FK programming: You have attempted to delete a part program block to which another block refers. \n 712 1126 M112 is active during a cycle call. \n 725 1141 M120 with LA = 0 during active tool radius compensation not permitted. \n 726 1142 M120 with LA greater than 0 permitted only during active tool radius compensation. \n 727 1143 - You cannot change the tool radius compensation while M120 is active. - You programmed a tool radius compensation RR/RL in an LN block, but the TNC will calculate the compensation from the normal vector NX, NY, NZ. \n 728 1144 Paraxial radius compensation (R+/R-, ISO: G43/G44) is not permitted when M120 is active. \n 729 1145 When M120 is active, rounding radius is permitted only in the compensation plane. \n 730 1146 When M120 is active, chamfer is permitted only in the compensation plane. \n 731 1147 Function definition for laser power control missing in machine parameter 3013/3014. \n 732 1148 Ambiguous function definition for laser power control in machine parameter 3013/3014. \n 733 1149 The permissible input range of a machine parameter was exceeded. \n 734 1150 The probe system is not ready. \n 735 1151 Re-entry with GOTO during active M120 not permitted. \n 736 1154 File name/path is not allowed. \n 737 1170 You have attempted to start a digitizing cycle for a triggering probe, although a measuring probe is defined in machine parameter 6200. \n 738 1171 You have attempted to start a digitizing cycle for a measuring probe, although a triggering probe is defined in machine parameter 6200. \n 739 1172 You have attempted to automatically measure a tool, although the table probe is not yet calibrated. \n 745 1178 You have attempted to traverse the reference marks with NC start, although the "rotate working plane" function is active. \n 749 1182 An incorrect value exists in a machine parameter. \n 750 1186 This error message will be displayed upon opening a binary file (*.H,*.T...) if the binary format has changed since the previous output version. \n 751 1187 M89 is not allowed during Cycle 9 PGM CALL. \n 753 1192 - The solid angles programmed in Cycle 19 Tilt Working Plane (DIN/ISO: G80) cannot be realized with the current attachment (e.g. universal head where only one hemisphere is accessible). - Run probing cycle only with paraxial angular position. - The point angle (T-ANGLE) defined for the active tool is 180°. \n 754 1193 Automatic tool measurement: Number of teeth not transferred into the tool table. \n 766 1266 Binary format of a plain language block is incorrect. \n 767 1521 A PLC error table selected in the OEM.SYS file has been recompiled after a change. \n 768 1523 After an interruption in power, the PLC error table cannot be automatically compiled because there is no table selected in OEM.SYS. \n 769 1524 There is no PLC error table. - A PLC error module 9085/9086 was called although no error table was compiled, or there were no entries in the table. - A PLC error module 9085/9086 was called or an error marker was set, although the error table was edited or erased after compilation. \n 770 1525 The PLC error table selected in OEM.SYS is not a PET file. \n 771 1527 The PLC error table in the OEM.SYS file was not found. \n 772 1528 PLC error table: The error table selected in the OEM.SYS file does not have an up-to-date binary format (e.g. after a software exchange). \n 803 1568 In the selected point file, which limits the digitizing range, no coordinates of the working plane have been saved. \n 809 1590 The value entered for 'DIST' in the digitizing cycle 16.0 MEANDER or 18.0 LINE is smaller than the minimum permissible distance that the TNC calculates from the machine data. \n 810 1682 Cycle 22 needs informaion on the tooth length and the plunge angle of the active tool. - The data for LCUTS and ANGLE are missing in the tool table - The tool table is not active \n 822 1745 - You attempted to open a file during a write access - e.g. through the data interface - or vice versa. - You attempted to open a locked file. - You attempted to erase or rename a protected file. - You attempted to erase the main directory (TNC:\) \n 825 1749 The number combination of the system datum (FN17/FN18, ISO: D17/D18) is not permitted. \n 827 1750 Fatal error during PLC module call (e.g. Module 9031: error converting MP). \n 829 1789 The tool was locked (e.g. after breakage). \n 830 1790 Cycle 15 (RANGE) is active during the start of a contour line cycle. \n 831 1791 The probe point interval in a digitizing cyle was programmed by Q parameter as a value greater than 6,5535 mm. \n 832 1792 - During a meander or contour line cycle the line axis is the same as the probe axis. - There is no line axis in the range definition (RANGE cycle). \n 833 1793 Digitizing with measuring touch probe: In the meander or contour line cycle you defined a rotary axis as column axis. \n 834 1794 During digitizing with rotary axes the rotary axis is not parallel to the line axis or column axis. \n 835 1795 - A rotary axis is active in the range during the start of a contour line cycle. - Digitizing with measuring touch probe: A rotary axis is defined in the range during the start of a meander cycle. - Touch probe axis in the range cycle is not the same as the calibrated touch probe axis in the manual mode. \n 836 1796 - The point spacing in a digitizing cycle was programmed by Q parameter at a value greater than 6.5535 mm. - The line spacing in a digitizing cycle was programmed by Q parameter as a negative value. - Digitizing with measuring touch probe: The minimum line spacing is greater than the line spacing, or it was entered as zero. \n 837 1797 There was no range cycle defined before the start of a digitizing cycle. \n 838 1798 The digitizing range exceeds the traversing range (limit switch). \n 839 1799 The clearance height entered in Cycle 8 or Cycle 18 was less than the MIN point of the touch probe axis in the Range cycle. \n 847 1807 Syntax error during file-name input. \n 849 1809 The M functions M114 and M116 cannot be used together. \n 850 1810 This error occurs when the TNC does not have enough buffer memory for calculations, e.g. for generating complex FK graphics while machining a complex part. \n 879 1845 The system files on your hard disk are no longer up-to-date. \n 882 1848 You attempted to erase a directory that still contains files. \n 884 1850 The main axis and its associated parallel axis is not permitted in the rectangular pocket cycle. \n 885 1851 The function M130 is permitted only for a tilted working plane. \n 886 1852 The function M130 is not permitted together with M114. \n 887 1853 The function M130 is permitted only for line interpolation. \n 888 1854 The function M130 is not permitted at together with radius compensation. \n 891 1855 There is no fixed cycle defined before Cycle 220/221 (circular/linear point pattern). \n 896 1856 In the Rough-Out cycle, the reciprocation feed rate has not yet been defined. \n 897 1857 Rough-Out Cycle: The radius of the fine-roughing tool is too large. \n 916 1892 Condition in FN20 (ISO: D20): Wait is not permitted. \n 925 1900 You attempted to interrupt the connection to a device (e.g. network), although the TNC is still accessing the device. \n 926 1901 The NFS server cannot find the drive that you selected. \n 933 1914 Automatic tool measurement: The breakage tolerance (LBREAK or RBREAK) from the tool table was exceeded. \n 935 2039 You have called a datum number that does not exist in the active datum table. \n 936 2040 The width defined in the slot cycle cannot be machined with the active tool. \n 937 2041 The side lengths defined in the Pocket Milling cycle are too small. \n 938 2042 There is no plunging depth (Q202) defined in the fixed cycles 200 to 215. \n 939 2043 In the Universal Drilling cycle, you have not defined the minimum plunging depth. \n 940 2044 Pocket milling cycle: Q218 must be greater than Q219. \n 941 2045 Cycle 210 cannot be run in the CIRCULAR PATTERN or LINEAR PATTERN cycle. \n 942 2046 Cycle 211 cannot be run in the CIRCULAR PATTERN or LINEAR PATTERN cycle. \n 943 2047 Pocket finishing or stud finishing cycle: Rounding radius Q220 is too large. \n 944 2048 Stud finishing cycle: Workpiece blank diameter Q222 must be greater than the finished part diameter Q223. \n 945 2049 Circular Pattern cycle: You entered a pitch circle diameter of zero. \n 946 2050 Circular Pattern cycle: Enter a stopping angle equal to the starting angle. \n 947 2051 Circular Pattern cycle: You entered an angle range greater than 360°. \n 956 2100 Pallet changer: The part program that was started belongs to another pallet. \n 957 2101 Pallet changer: A pallet change was started although there is no NCMACRO.SYS file. \n 958 2102 Pallet changer: A pallet change was started although the PALLET entry is missing in the NCMACRO.SYS file. \n 959 2103 Pallet changer: You started a part program that does not belong to any pallet. \n 960 2186 Tilting the working plane: Tool axis for the setup clearance in Cycle 19 is missing. \n 961 2211 A TOOL CALL is not permitted with M128 active. \n 962 2212 M91 or M92 were programmed with M128 active. \n 963 2213 M128 without machine geometry description MP 7500 and following. \n 970 312 While defining the Contour Lines cycle (TCH PROBE 7) you programmed a height axis in the starting point. \n 972 2222 You attempted to use a workpiece-material table or a tool-material table, although your machine manufacturer has not made the required entries in OEM.SYS. \n 973 2223 You searched for a table that does not have the file extension .TAB. \n 974 2224 In the definition of a freely definable table you used a field name that is not an element of the table. \n 975 2225 You attempted to select a tool material or a cutting material, although the corresponding table has no entries. \n 976 2226 The workpiece material entered in OEM.SYS was not found. \n 977 2227 The cutting material table integrated in OEM.SYS was not found. \n 978 2228 You attempted to have the TNC automatically calculate the feed rate without first selecting a workpiece material in the workpiece blank definition. \n 979 2229 In the tool table you refer to a cutting-data table in which the workpiece-material/tool-material combination that you selected does not exist. \n 980 2230 You attempted to call a tool without first assigning it a cutting data table. \n 997 2231 The highlighted block is not permitted with M112 active. \n 998 2232 In the active part program there are ERROR blocks that cannot be run by the TNC (e.g. TOOL DEF block - ISO: G99 block - with active tool file). \n 999 2233 You attempted to resume the program at an FK block that contains Q parameters. \n 1000 2238 In the Circular Pocket Finishing cycle (Cycle 212, ISO: G212), you entered a finished-part diameter (Q223) smaller than the workpiece-blank diameter (Q222). \n 1004 2243 Cycle 22 (ISO:G122) ROUGH-OUT: The plunge angle of the active tool is too small. \n 1011 2253 The machine control voltage is still switched on. \n 1012 2254 In the relay chain the normally closed contact of one or more relays is open. \n 1013 2255 The machine control voltage is switched off. \n 1014 2273 During multiple measurement with the automatic probe cycle the variance of the individual measured values is greater than the value defined in machine parameter MP6171. \n 1015 2284 The window for the help text could not be displayed. It could be that a help window is already open in another operating mode. \n 1016 2285 The datum point for this axis is disabled in machine parameter MP7295. \n 1017 2288 The tool holder does not open or close. \n 1023 2300 You have altered the entries for automatic cutting data calculation in the part program block WMAT or in the TOOL CALL block (ISO: G99 block). \n 1026 2315 In the definition of Cycle 204 you have entered the disengaging direction 0. \n 1027 2316 In the system file OEM.SYS the file defined with PLCEVENTS= was not found. \n 1028 2317 More than 15 events were defined for the current SPAWN process (cooperative multitasking). \n 1029 2319 The tool type table entered in OEM.SYS was not found. \n 1030 2320 The path entered in OEM.SYS for the display of cutting data (CDT files) was not found. \n 1031 2321 There are more than 128 cutting data tables (*.CDT) in the specified directory. \n 1034 2336 Safety-oriented input of MC is not equal to input of CC. Example: RRK.x, SRG.AS.x, SRG.T.x, BA3.x \n 1036 2339 The connection to the NFS server was interrupted. \n 1037 2342 In the function "Write System Data" you entered an assignment value that lies outside of the permitted input range. \n 1039 2344 You forgot to enter an element required to complete the block or cycle. \n 1040 2345 You have called a tool that is not defined in the tool table. \n 1066 2375 You must not program M112 together with M128. \n 1067 2377 You have traversed the hardware limit switch. \n 1068 2378 During acceleration or deceleration the machine did not behave as instructed by the software. \n 1071 2377 You have traversed the hardware limit switch. \n 1073 2384 While editing the structure of a freely definable table you erased all the elements. \n 1074 2385 While editing the structure of a freely definable table you deleted an element that is always required by the TNC (mandatory element). \n 1075 2386 In a freely definable table, the sum of the column widths of all elements exceeds the maximum permissible line length of 200 characters. \n 1076 2387 You changed the structure of a freely definable element. During conversion of an element one of the following errors occurred: - Incorrect number range defined - Permissible column width was exceeded - An element contains impermissible characters \n 1146 2500 You attempted a mid-program startup by pressing GOTO block number, although it is defined in machine parameter 7680 that a spline be inserted as connecting element at radius- compensated outside corners. \n 1147 2504 In a probing cycle you entered 0 for the traverse direction Q267. \n 1148 2505 Probing cycle for datum setting: You want the TNC to write the measured point into a datum table, but you have not activated a datum table in a program run mode (status M). \n 1149 2506 Probing cycle for workpiece measurement: Center of 1st axis outside of position tolerance. \n 1150 2507 Probing cycle for workpiece measurement: Center of 2st axis outside of position tolerance. \n 1151 2508 Probing cycle for workpiece measurement: Hole diameter too small for tolerance. \n 1152 2509 - Probing cycle for workpiece measurement: Hole diameter tolerance exceeded. - Cycle 208: The programmed hole diameter (Q335) cannot be machined with the active tool. \n 1153 2510 Probing cycle for workpiece measurement: Stud diameter too small for tolerance. \n 1154 2511 Probing cycle for workpiece measurement: Stud diameter too large for tolerance. \n 1155 2512 Probing cycle for workpiece measurement: Pocket length in 1st axis too small for tolerance. \n 1156 2513 Probing cycle for workpiece measurement: Pocket width in 2nd axis too small for tolerance. \n 1157 2514 Probing cycle for workpiece measurement: Pocket length in 1st axis too large for tolerance. \n 1158 2515 Probing cycle for workpiece measurement: Pocket width in 2nd axis too large for tolerance. \n 1159 2516 Probing cycle for workpiece measurement: Stud length in 1st axis too small for tolerance. \n 1160 2517 Probing cycle for workpiece measurement: Stud width in 2nd too small for tolerance. \n 1161 2518 Probing cycle for workpiece measurement: Stud length in 1st axis too large for tolerance. \n 1162 2519 Probing cycle for workpiece measurement: Stud width in 2nd axis too large for tolerance. \n 1163 2520 Probing cycle 425 or 427: The measured length exceeds the maximum permissible value. \n 1164 2521 Probing cycle 425 or 427: The measured length is below the minimum permissible value. \n 1165 2522 Probing cycle 426: The measured length exceeds the maximum permissible value. \n 1166 2523 Probing cycle 426: The measured length is below the minimum permissible value. \n 1167 2524 Probing cycle 430: The measured bolt-hole-circle diameter exceeds the maximum permissible value. \n 1168 2525 Probing cycle 430: The measured bolt-hole-circle diameter is below the minimum permissible value. \n 1169 2526 The tilted working plane function is active during execution of a digitizing cycle or definition of a PRESET. \n 1175 2609 You attempted to activate the Tilted Working Plane functions and M128 simultaneously. \n 1176 2610 You attempted to activate M114 and M128 simultaneously. \n 1177 2611 You attempted to activate M128 while radius compensation was active (RL/RR, ISO: G41/G42). \n 1178 2617 You failed to define the measuring axis in one of the measuring cycles 400, 402, 420, 425, 426 or 427. \n 1179 2618 While creating a log you entered an illegal format for the date or time. \n 1181 2621 You attempted to set a new datum while M128 was active. \n 1185 2635 During workpiece inspection using a measuring cycle, the tool breakage tolerance RBREAK given in the tool table was exceeded. \n 1186 2636 You activated M128 while a tool radius compensation RL/RR (DIN/ISO: G41/G42) was still active. The TNC cannot switch from 2-D to 3-D radius compensation. \n 1190 2642 After a "safe stop" the inverter did not return to the ready state. \n 1191 2644 You attempted to cancel radius compensation immediately behind a positioning block with M120. In order to be able to check for potential collisions, however, the TNC requires several radius-compensated positions. \n 1192 2645 In a touch probe cycle you defined a clearance height (Q260)below the measuring height (Q261). Collision risk! \n 1193 2646 Contact of a machine key does not open. \n 1194 2647 In the relay chain, the normally closed contact of all relays is closed. \n 1195 2655 The spindle motor is receiving current although its inverterwas switched off! \n 1196 2657 The axis motor is receiving current although its inverter was switched off! \n 1197 2662 You attempted to mark the BEGIN block (ISO: first block with %) or the END block (ISO: block N 999999). \n 1198 2663 You attempted to insert a copied block behind the END block (ISO: block N 999999). \n 1199 2664 You attempted to insert blocks from intermediate memory, although you haven't copied anything since power has been on. \n 1200 2665 You attempted to fill the intermediate memory using the DELETE BLOCK, COPY BLOCK soft keys, although you have not yet marked a block. \n 1201 2668 The program contains blocks (indicated with ERROR) with incorrect block format. \n 1205 2691 The tool direction given in the LN block (TX, TY, TZ) cannot be realized with the active swivel head configuration. \n 1206 2692 The rotary-axis coordinate resulting from M128 and from the tool direction given in the LN block (TX, TY, TZ) cannot be realized with this swivel head configuration. \n 1207 2695 Error in program run \n 1208 2700 The MC (Main Computer Unit) failed to test the cutoff channels. \n 1214 2711 Checksum was not yet entered, or it is incorrect. \n 1227 2733 While editing the structure of a configurable table, you attempted to enter more than the permissible 30 columns. \n 1228 2734 While editing a pallet table, you pressed the actual- position-capture key and the PRESENT VALUE soft key, although the highlight was not on an axis column. \n 1229 2735 You attempted a mid-program startup in a program that contains the miscellaneous function M128. \n 1230 2736 You attempted to use FN27 to write to a table, or FN28 to read from a table, although no table was open. \n 1231 2737 You entered an excessively long field name in an FN27 or FN28 function. \n 1232 2738 You attempted to use an FN27 or FN28 function to write to or read from a non-numerical field. \n 1233 2739 You entered more than 8 field names in an FN27 or FN28 function. \n 1245 2745 1) Signal of the reference pulse is disturbed (ground shield). 2) Position ascertainment via Z1 track is faulty. 3) Incorrect encoder line count. \n 1246 2746 Input value of the machine parameter MP2180 (PWM frequency) in incorrect. \n 1247 2747 You attempted to edit or erase a write-protected line. \n 1248 2748 You attempted to run a measuring cycle while M114 was active. \n 1249 2749 You attempted to run a measuring cycle while M128 was active. \n 1250 2750 You attempted to run the funtion M138, although one of the functions M114, M128, or tilted working plane was active. \n 1252 2752 You entered a machine parameter that does not match the default value set by your machine tool builder. \n 1253 2757 The CC could not run so many commands from the MC. \n 1254 2758 The command confirmed from the CC as an echo is not the command sent from the MC. \n 1255 2760 One or more S functions within a cycle were not performed. \n 1258 2768 The permissive button of the handwheel was pressed. An incorrect handwheel was selected by MP7640. \n 1259 2769 Informational message that the TNC has erased an incomplete cycle. \n 1260 2770 You attempted to insert a block from an empty intermediate memory. \n 1261 2771 You have selected a write-protected file for editing. \n 1262 2772 During editing you attempted to delete a word that is a required element of a function. \n 1263 2773 You attempted to open another context within a context dialog sequence. \n 1264 2774 You pressed the P key to enter polar coordinates. Polar coordinates are not programmable for the active function. \n 1265 2775 You attempted to change a context initiator to which other elements in the current block belong. \n 1266 2776 You entered a function that cannot initiate a context. \n 1267 2777 You attempted to end a Q-parameter block containing an odd number of parentheses. Parentheses can be programmed only in pairs. \n 1308 2820 The calculated position deviation between speed encoder and position encoder is greater than the value from MP640.x. \n 1309 2824 You attempted to run a cycle for tool measurement while the tilted-plane function was active, although the touch probe was not calibrated in the tilted working plane. \n 1310 2825 You attempted to run a cycle for tool measurement, although the touch probe was last calibrated in a tilted working plane. \n 1311 2826 You attempted to run a cycle for tool measurement although the touch probe is not parallel to the tool axis. \n 1312 2827 The braking process was not started, or it was started after a delay. \n 1313 2828 The time frame for the position controller is too small. It can be increased in MP7600.0. \n 1314 2829 In a measuring cycle you entered in parameter Q247 an angular step of 0. \n 1315 2830 In a measuring cycle, you entered in parameter Q247 an angular step smaller than 5 degrees. \n 1316 2834 The encoder with EnDat interface is defective. The error codes have the following meanings: 001 Light source defective 010 Signal amplitude too low 100 Positions value incorrect \n 1317 2837 Automatic FK conversion at NC start not possible. FK section may be located at the end of the program. \n 1328 2849 The spindle start key was pressed but not the permissive key while the protective door A/S was open. \n 1331 2853 The positions of two synchronized axes differ by a value greater than that defined in machine parameter MP855. \n 1333 2858 The detachable-key switch does not permit axis testing. The "untested" status remains in effect. \n 1343 2868 You tried to start tool measurement although the REF coordinates of one or more rotary axes (or parallel axes) do not agree with the coordinates defined in machine parameters MP6586.x. \n 1344 2945 - You tried to use M91 or M92 to move to a machine-based position while a tilted working plane and tool radius compensation were active. - You tried to use M91 or M92 to move to a machine-based position while a tilted working plane and M112 were active. - You programmed positioning blocks with M91 or M92 within a program while global program settings were active. - You tried to filter a program that contains NC blocks with M91 or M92. \n 1350 2187 Error in the power stage of the displayed axis. \n 1353 2969 You attempted to save an NC block although you have not entered all values required for the elements programmed in the block. \n 1359 2993 When the szervíz support ON/OFF soft key was pressed there was no valid Internet address entered under the code word SERVICE.REQUEST.HOST or SUPPORT.REQUEST.HOST in the OEM.SYS file. \n 1360 2995 During a return to the contour, the PLC commanded an illegal PLC datum shift. \n 1361 2996 During a return to the contour, the PLC commanded an illegal traverse range shift. \n 1362 3002 The code number 561320 is nonfunctional because the servicing mode for the spindle was not enabled by the machine tool manufacturer. \n 1366 3006 You have tried to perform a probing function without an active touch probe. Machine parameter 7411, bit 2 is set so that the calibration data is always taken from the tool table TOOL.T. \n 1369 3012 You used the M120 function during peripheral milling with active radius compensation. \n 1370 3013 Peripheral milling is permitted only for straight line blocks L (ISO: G00, G01) or LP (SO: G10, G11). \n 1371 3025 You attempted to run a locked pallet line. \n 1372 3026 The TNC cannot execute radius compensation on the programmed contour. Possible cause: You programmed two tangentially connecting straight lines in sequence. \n 1373 3055 In a fixed cycle you did not define the cutting direction (climb or up-cut). \n 1374 1149 The permissible input range of a machine parameter was exceeded. \n 1375 958 Error message after power interruption. \n 1376 1182 An incorrect value exists in a machine parameter. \n 1377 3063 An incorrect path or file name of a kinematic description is saved in the assignment table for kinematic descriptions. \n 1378 3065 You attempted to activate a kinematic description, although one of the functions M114, M128 or the tilted-working-plane cycle is active. \n 1383 3081 The programmed thread depth plus 1/3 of the pitch is greater than the drilling or sinking depth. \n 1404 3187 You have called a fixed cycle with CYCL CALL PAT without having activated a point table. \n 1405 3188 You have called a fixed cycle with CYCL CALL PAT, and the coordinate you have entered in the tool axis (clearance height) is too small. \n 1406 3189 You have used Cycle 12 (ISO: G39) to declare a program containing CLCL CALL PAT to be a cycle. \n 1407 3192 You have attempted to perform a measurement with Cycle 440 without first performing a calibration. \n 1408 3193 The limits entered in the tool table TOOL.T in the LTOL or RTOL column were exceeded. \n 1411 3199 - During a mid-program startup, the active gear range did not match the gear range at the restore position. - During a mid-program startup, the active spindle did not match the spindle required at the restore position. \n 1417 3205 You have attempted to activate the autostart function although it was not enabled by the machine tool builder. \n 1418 3206 During a program abort the TNC was not able to run a macro defined by your machine tool builder. \n 1427 2720 The amplitude of the encoder signals is too large, or the signal for contamination is active. \n 1428 44 The amplitude of the encoder signals is too small, or the signal for contamination is active. \n 1429 45 The maximum input frequency was exceeded at an encoder input. \n 1430 2710 The automatic, SRG, SBH, and SH operating statuses are compared cyclically between MC and CC. If they are unequal for a duration greater than 500 ms, it releases a Stopp1 (emergency stop). \n 1431 2688 The 5V power supply of the LE is outside the tolerance range. \n 1432 2687 The temperature inside the LE is outside the tolerance range. \n 1433 2612 The safety-oriented inputs for detachable-key switches, door contacts and emergency stop were not set to 0 during the cyclic test. \n 1434 2376 Feed rate too high for safe operation. Feed rate for BA3 is defined with MP540.x. For special operation, MP552.x applies. \n 1435 2376 Feed rate too high for safe operation. Feed rate for BA3 is defined with MP540.x. For special operation, MP552.x applies. \n 1436 14018 - The position error in the safe controlled stop (SBH) is greater than the value specified in machine parameter MP545.x. - If during an emergency stop the axes and spindle are decelerated, and the axes come to a stop earlier than the spindle, then the axes are standstill-monitored at the value from MP545.x until the spindle comes to a stop. - If the protective door is closed in the automatic mode, axes whose drives are switched off (e.g. locked axes) are standstill monitored at the value from MP545.x. - After the permissive button is released, the tool magazine axis moves farther than the path specified in machine parameter MP550.x. - After the permissive button is released, the tool magazine axis continues to move for more than 3 seconds. \n 1437 57 The calculated tool path exceeds the machine's traverse limits. Negative traverse range is defined with MP670.x. \n 1438 57 The calculated tool path exceeds the machine's traverse limits. Negative traverse range is defined with MP670.x. \n 1439 55 The calculated tool path exceeds the machine's positive traverse limits. Positive traverse range is defined with MP650.x. \n 1440 55 The calculated tool path exceeds the machine's positive traverse limits. Positive traverse range is defined with MP650.x. \n 1441 2336 Safety-oriented input of MC is not equal to input of CC. Example: RRK.x, SRG.AS.x, SRG.T.x, BA3.x \n 1442 3213 Rotational speed too high for safe operation. Rotational speed for BA3 is defined with MP541.x. For special operation, MP551.x applies. \n 1443 3213 Rotational speed too high for safe operation. Rotational speed for BA3 is defined with MP541.x. For special operation, MP551.x applies. \n 1444 3214 During a program run, you changed a value in a datum table or point table while in the Programming and Editing operating mode. The TNC was no longer able to include the new value in its geometry look-ahead calculation. \n 1445 3218 During mid-program startup, the PLC function programmed in the displayed block cannot be properly executed. \n 1446 3219 Safety-oriented function: The axis moved from the test position before you pressed the permissive button. \n 1447 3220 The tolerance value entered in MP6510.0 cannot be attained during radius measurement with the TT. \n 1448 3221 The tool radius that you entered for the calibration tool is too large. \n 1452 3231 The mandatory PAL/PGM column is missing in a pallet table. \n 1453 3232 Setup version does not match the NC software. \n 1455 3234 The pocket change for tool preselection is still in progress. The programmed tool change is not yet possible. \n 1456 3235 You have defined for the feed rate a negative value or negative Q parameter. A negative value resulted from the feed rate calculation by Q parameter. \n 1457 3236 The axis position last saved does not match the present position of the rotary encoder with EnDat interface. \n 1458 3239 The selected software could not be loaded into the flash ROMs. The previous software will be used. \n 1459 3243 - At his point in the program you have not yet defined a tool axis. - M140 requires a tool axis for retraction. \n 1460 3245 The M functions M89 ... M299 cannot be run in the MANUAL OPERATION or ELECTRONIC HANDWHEEL modes. Only M functions that are output to the PLC can be run. \n 1461 3354 You attempted to program one of the functions M114, M116, M128, M144 or Cycle 19, although you have already activated one of them. These functions are mutually exclusive. \n 1462 3356 - Selected line in the assignment table not found. - The table for kinematic description is empty or missing. - A column in the assignment table is missing or has an incorrect entry. \n 1463 3357 The machine parameter subfile entered in the assignment table for kinematic description contains incorrect entries. \n 1464 3441 You attempted to execute the function M138, although the function M144 was active. \n 1465 4957 The values that you entered are contradictory. \n 1467 3532 You have entered an illegal value or number in FUNCT.TAB. \n 1468 3927 The active probe axis was not positioned with M114 parallel to a machine axis before probing. \n 1469 3928 You attempted to activate M112 and M144 at the same time, although tilting axes are in motion. \n 1474 4175 The pallet line under the cursor is marked as a completed part and can therefore no longer be executed. \n 1475 4176 Fixture changer: A fixture change was started, although no NC program is indicated for changing the fixture. \n 1476 4177 During tool-oriented machining, you attempted to resume machining of a damaged or missing part with a saved context. \n 1477 4197 Mid-program startup is not permitted with the programmed function. \n 1503 4276 Spindle cannot be oriented. \n 1548 4491 The file MGROUPS.SYS is faulty or missing. \n 1549 4492 The permissive button of the tool changer was pressed. \n 1550 4571 The cycle can be run only in negative direction (or positive direction in Cycle 204) because in MP7441 bit 2 is set to 1. \n 1551 4572 You attempted to enter a character that is not allowed in the entry box. \n 1552 4573 You attempted to enter a lowercase letter. \n 1553 4574 You attempted to enter a letter. \n 1554 4575 You attempted to enter a numeral. \n 1607 4880 There are too many NC software versions on the control. \n 1608 4881 Missing or incorrect entry in the OEM.SYS file \n 1609 4882 You tried to execute function M140 although the position to be approached is outside the range of traverse. \n 1610 4903 During three-dimensional tool compensation (face milling or peripheral milling), you tried to use a tool with a positiveoversize. On concave contours this can cause gouging. \n 1611 4905 The temperature sensor on processor 1 (processor board) has detected an excessively high temperature. \n 1612 4906 The temperature sensor on processor 2 (processor board RTPC) has detected an excessively high temperature. \n 1640 4935 You attempted to - save the actual position with PLC Module 9146 while the position control loop was closed. - close the position control loop, although the actual position was saved with PLC Module 9146. \n 1691 5073 - DSR signal missing \n 1692 5074 - Character error in the telegram \n 1693 5075 - Checksum error in the received telegram \n 1694 5076 - Checksum error in the transmitted telegram \n 1695 5077 - No reaction from distant terminal (T1) \n 1696 5078 - Distant terminal not ready \n 1697 5079 - Telegram incomplete, ETX missing (T0) \n 1698 5080 - No reaction from distant terminal (T2) \n 1699 5081 - Internal software error \n 1700 5099 Internal software error \n 1701 5225 The software version installed in the control is not the version originally provided by HEIDEHAIN. The control can be used only as a programming station. \n 1702 5228 You programmed a feed rate = 0 \n 1703 5236 The temperature sensor in the control detects an excessive temperature within the control housing. A further increase in temperature may damage the control hardware. \n 1704 5242 - The PLC program was not compiled after switch-on, was compiled incorrectly, or it has been edited since it was last compiled. - You attempted to activate the In Code Tracer or the monitoring list, although the PLC program was not yet compiled since switch-on or was edited since it was last compiled. - For more detailed information on the cause of this error, refer to the PLC main menu. \n 1705 204 The temperature sensor in the LE has detected an excessively high temperature inside the control housing. \n 1706 5286 Error during evaluation of the Profibus configuration. \n 1707 5287 Error during access to the Profibus hardware. \n 1708 5288 Error during initialization of the Profibus hardware. \n 1713 5312 Code number 531210 was entered. \n 1731 5338 - The soft-key project was not yet translated after switch-on, or it was edited after translation. - For more information on the cause of error, refer to the PLC main menu. \n 1743 5366 You attempted to insert a line at the current cursor position. \n 1744 5367 You attempted to define a tool that is already defined in the program. \n 1745 5368 You attempted to define a LBL that is already defined in the program. \n 1746 5369 In the MOD settings of the machining modes, no axes were selected for L-block generation. \n 1755 2612 The safety-oriented inputs for detachable-key switches, door contacts and emergency stop were not set to 0 during the cyclic test. \n 1756 2687 The temperature inside the LE is outside the tolerance range. \n 1757 2688 The 5V power supply of the LE is outside the tolerance range. \n 1776 5434 You attempted to perform a function that is not included in the current NC software. \n 1784 5479 - The magazine rules have not been translated since switch-on, or they were edited since they were last translated. - For more detailed information on the cause of the error, refer to the PLC main menu. \n 1785 5484 - Datum setting with tilted working plane is inactive: The tilting axis position is not equal to 0°. - Datum setting with tilted working plane is active: The positions of the tilting axes do not match the active angular values. \n 1792 5566 You attempted to change the coordinate data in the present block from Cartesian to polar or vice versa. \n 1793 5567 Internal software error \n 1794 5568 You exceeded the maximum permissible number of characters for the active input box. \n 1795 5569 You attempted to enter a numerical value that lies outside the permissible range. \n 1796 5570 You attempted to enter a value that exceeds the permissible number of decimal places. \n 1797 5571 You attempted to enter an algebraic sign with the -/+ key. \n 1798 5572 You attempted to enter a number with decimal places. \n 1799 5573 You attempted to use a Q parameter in the active input box. \n 1800 5574 You attempted to enter an incremental value by pressing the I key. \n 1801 5575 Too many M functions for one NC block. \n 1802 5576 - An NC block has more than the allowed number of simultaneously movable axes. - You tried to use an NC program to make a reverse program in which more than 5 axes are programmed. \n 1803 5577 You programmed the same axis more than once within one NC block. \n 1804 5578 - You used the same syntax element more than once within one NC block.- The current sequence of syntax elements in an NC block do not comply with requirements. \n 1805 5579 Not all required data have been entered in an NC block. \n 1806 5580 An NC block in an ISO program begins without a block number N. \n 1807 5581 Not all required data have been entered in an NC block. \n 1808 5582 An NC block contains a syntax element that requires other syntax elements. \n 1809 5583 No measured value was saved in the counter chip during probing. \n 1843 5617 In an NC block, you attempted to enter a word that the TNC cannot interpret. \n 1844 5618 You attempted to edit a syntax element in an NC block. \n 1845 5619 In a program, you attempted to edit one of the blocks BEGIN PGM (ISO: %... G71), or END PGM (ISO: N99999999%...). \n 1847 5627 Incorrect distance between speed encoder and position encoder in MP1356.x during reference capture via the EnDat interface of the speed encoder (MP1355=1). The displayed value is the difference. \n 1848 5628 In an NC block, you programmed more axes than have been enabled through the SIK (System Identification Key). \n 1849 2652 The power supply of the spindle could not be switched to ready condition. \n 1850 2653 The power supply of an axis could not be switched to ready condition. \n 1851 2654 The spindle power supply is ready for operation although it ought to be switched off. \n 1852 2656 The power module of an axis is ready for operation although it should actually be switched off. \n 1853 2743 Checksum error due to faulty data. \n 1854 2759 Command was not acknowledged by the Computer Control Unit (CC) within 200 ms. \n 1855 2819 Faulty software \n 1856 2821 For a certain time the CC has not sent any position values to the MC. \n 1857 2822 The MC must not send any position values to the CC. \n 1858 2823 Contradictory status of checked position values in the MC and CC. \n 1859 2831 - The version number of one of the called Include files are different in the MC and CC - Internal software error \n 1860 5097 Internal software error \n 1861 5096 - Hardware error - Internal software error \n 1862 2743 Checksum error due to faulty data. \n 1863 5631 Command was not acknowledged by the Main Computing Unit (MC) within 400 ms. \n 1864 5632 Main Computer and Controller Unit mismatch. \n 1865 5635 More than four channels per controller board selected. \n 1866 5641 Safety doors are open. \n 1868 5651 You programmed a positioning block that is to offset a tool length. However, no tool axis has been defined. \n 1869 5655 The axis was not yet tested. \n 1876 5671 Disagreement of position values before power-off and after power-on. \n 1877 5672 You attempted to activate a ref-based datum through Cycle 7. REF-based datum tables are no longer available as of NC software number 340 422-01. \n 1878 5673 In one of the measuring cycles 410 to 418, you did not define the parameter Q303 (measured value transfer)(current value = -1). For reasons of security, however, selection of the measured value transfer is required to write the results of measurement in a table (datum table or preset table). \n 1879 5693 You called probing cycle 419 with an invalid tool axis. \n 1881 5699 In probing cycle 418, the TNC calculated too large a value. You may have defined in an incorrect sequence for the four holes to be probed. \n 1882 5700 - In one of the probing cycles 400, 403 or 420, you defined a contradictory combination of measuring points and measuring axes. - The selection of measuring points in Cycle 430 results in division by 0. \n 1888 5709 Unsuccessful calculation of a circle with function FN23 or FN24. \n 1889 5712 In the network settings, the code word password= is undefined. \n 1890 5713 In the network settings, the code word password= is defined, but it has no associated text. \n 1891 5714 The password defined in the network settings is too long. \n 1892 5715 You tried to encode a password that has already been encoded. \n 1904 5757 An attempt was made to use the Preset table to activate a datum for an axis that has been locked with machine parameter 7294. \n 1906 5759 In Cycle 20 (ISO: G120), you entered a clearance height (Q7) that is lower than the coordinate of the workpiece surface (Q5). \n 1920 5969 Warning before deleting an NC block. \n 1921 5970 An attempt was made to program an axis that is not allowed for the currently active function. \n 1922 5971 You attempted to cancel the Block Skip funktion with the Backspace key. \n 1923 5972 You attempted to enter an NC block in which a syntax element was not concluded with the required apostrophe. \n 1937 6018 During activated double referencing, a probe cycle was started although the reference mark of the position encoder was not yet traversed. \n 1938 6027 You programmed an illegal axis in probing cycle 3. \n 1952 6049 There are too many error messages defined in the PET table. \n 1953 6052 The plunging strategy defined in Cycles 251 to 254 contradicts the defined plunging angle of the active tool. \n 1954 6055 You attempted to run a fixed cycle in connection with Cycle 220 or 221, although they cannot be combined with these cycles. \n 1955 6066 In Cycle 32, a tolerance for rotary axes was programmed although the HSC filter is not active. \n 1956 6069 Internal software error \n 1959 6072 You moved the display position of the current block to the edge of the screen. \n 1961 6079 You programmed M128 although a rotary axis is defined as a noncontrolled axis. \n 1962 6080 You programmed M144 although a rotary axis is defined as a noncontrolled axis. \n 1963 6081 1. Key switch is not on BA1. \n 1964 6082 Wiring error at the SG inputs BA2.x, BA3.x and BA4.x. \n 1967 6086 - Target path or target file *.WLT in OEM.SYS (DEBUGPATH=) is incorrect. - Error during conversion of *.WLB to *.WLT format. - Cannot open *.WLT file (system error). \n 1968 6087 - Source path or source file *.WLT in OEM.SYS (DEBUGPATH=) is incorrect. - Error in the conversion of *.WLT to *.WLB format. - Cannot open *.WLB file (system error). \n 1969 6088 Cannot open TEMP.WLT (system error). \n 1970 6089 - Source path or source file *.WLT in OEM.SYS (DEBUGPATH=) is incorrect. \n 1971 6090 - Source path or source file of the PLC program is incorrect (MAINPGM= in OEM.SYS) - Source path to the debug information is incorrect(DEBUGPATH= in OEM.SYS) - *.WLC file without symbolic operands \n 1972 6091 No symbolic operands are being used in the PLC program. \n 1974 6094 Code number missing or incorrect. \n 1975 6093 No axes or spindles in safe mode. \n 1976 6099 - Invalid operand type (ADDR column) - Invalid operand address - Attempt to change a constant - Out of value range - Invalid characters in value \n 1977 6100 - Invalid operand type (M,B,W...) - Invalid address area - Alignment (invalid word or double-word address) \n 1978 6101 The BA4 operating mode is selected by key switch but has not been released in MP561. \n 1979 6102 The MODULE and SYMBOL columns are filled automatically and must not be overwritten. \n 1980 6103 - You tried to use a preset number that does not exist in the table PRESET.TAB. - PRESET.TAB does not exist. \n 1982 6105 In the BA2 mode of operation, you tried to move more than one axis. \n 1984 498 Error in compensation value calculation: The *.COM file selected in the *.CMA file does not exist. \n 1985 206 The program that you have selected contains a program call into a program that does not exist in TNC memory. \n 1987 6118 In the BA4 mode of operation, the permissive key was not pressed within the time defined in MP529. \n 2029 6182 The profibus configuration file is either not registered in the OEM.SYS file (keyword PROFIBUSCFG=) or it could not be found. \n 2030 6183 Cannot access the Profibus master board. \n 2031 6184 In the Profibus functions there is either a data access error or an error in the memory management. \n 2032 6187 In a Contour Pocket cycle or a Contour Train cycle you called more than 6 programs (PGM CALL, ISO: %..). A program call can also be: - Cycle 12 (PGM CALL, ISO: G39) - Calling an OEM cycle \n 2033 6188 You programmed more than 6 program calls (PGM CALL, ISO: %..). A program call can also be: - Cycle 12 PGM CALL (ISO: G39) - Calling an OEM cycle \n 2034 6189 The 5-V power supply of the control is too high. \n 2035 6190 The 5-V power supply of the control is too low. \n 2036 6193 The starting point of the spline is too far away from the end point of the previous contour element. \n 2039 6212 You attempted to load the actual position into the program while the tilted working plane function was active. \n 2054 6236 The PLC program was stopped because of a system error in the PLC. \n 2055 6264 The TNC is being so heavily utilized to machine the current workpiece that there is no more capacity available for the program-run graphics. \n 2056 6291 You tried to you use touch probe cycle 3 without first referencing the spindle. \n 2057 6294 A safety-oriented machine parameter was changed by the PLC. Such a change is not allowed. \n 2063 6307 The remaining tool life (TIME2 column in the tool table) of the tool indicated in the error text has been exceeded. \n 2064 6308 You called a tool that is not contained in the tool magazine. \n 2065 6309 You attempted to upload a file from the TNC containing special characters that cannot be transferred with the selected interface mode. \n 2068 6312 The given machine parameter subfile does not exist. \n 2069 6408 The given machine parameter subfile contains incorrect entries. \n 2070 6409 The PLC activated a strobe output in an M, S, or T2 function, although this function is configured for uninterrupted traverse on the NC. \n 2071 6410 The PLC activated a strobe output within one of the cycles 1, 2, 17 or 18 or during tool measurement. No PLC strobe outputs are permitted within these cycles. \n 2072 6411 The PLC attempted to change the limit switch during program run. This can be triggered, for example, by a time overlap between the NC start or the acknowledgment of an M/S/T strobe by the PLC and a switch of the traverse range. \n 2073 6412 An attempt was made to change a preset value during program run. This can be triggered, for example, by a time overlap between the NC start or the acknowledgment of an M/S/T strobe by the PLC and a switch of the traverse range. \n 2074 6413 An attempt was made to select another kinematic configuration during program run. This can be triggered, for example, by a time overlap between the NC start or the acknowledgment of an M/S/T strobe by the PLC and a kinematic selection by the PLC. \n 2075 6414 During restoration of the machine status after a block scan (mid-program startup), the conditions on the machine regarding spindle speed (S), traverse range (R) or preset (P) were not the same as calculated in the block scan. \n 2094 7222 - You tried to edit or delete a write-protected line in the preset table. - You tried to write a value in the active line of the preset table. \n 2095 7784 When a table was being written to, one of the following errors occurred: - Target line or column does not exist - The search text for finding the target was not found - No kinematic table is active \n 2096 7798 CC reports an error code for which there is no error message yet. \n 2097 7799 The brake test was started, but no end was received within 2 seconds from the CC. \n 2098 7800 On brake channel 1 MC there is a short curcuit with 24 V. \n 2099 7801 On brake channel 1 MC there is a short circuit with 0 V. \n 2101 7803 After a probing process you tried to set the datum with the ENT key. \n 2103 7798 CC reports an error code for which there is no error message yet. \n 2104 7815 - After the machine traversed the reference points, you tried to select a program run mode although the machine was not yet completely initialized. - You canceled the initialization process. \n 2189 7922 Supply voltage on connector X44 missing. \n 2190 7923 Automatic start of machine tool axis with open safety doors T. \n 2192 7935 You tried to save or open a binary coded file (NC program, table) on an external drive (network drive). \n 2193 7936 You named the same directory as source and target for copying. \n 2194 7937 You named the same file as source and target for copying. \n 2195 7938 When a synchronous motor operates with an encoder without Z1 track, the measured field angle is entered in MP2256.x and a unique control identification is entered in MP2257.x. The control ID entered in MP2257.x does not fit this control. The control ID of this control is given in parentheses. \n 2198 7964 The given tool vectors of two successive points permit no interpolation. \n 2203 7969 Due to insufficient system resources (e.g. memory-consuming high-speed cutting) a part of the system software cannot be loaded. \n 2204 7971 One of the processes required for editing files (e.g. background copying) could not be started. There may be too many of these processes already active. \n 2205 7972 The drive specified in the path is invalid. \n 2206 7973 You tried to rename a file so that the new file name would be identical to the old file name. \n 2207 7974 You tried to convert a binary-type file into another binary-type file. Type conversions are only possible between ASCII-type files, or from binary to ASCII (or vice versa). \n 2208 7975 - No more free space is available on the selected drive. - Too many files are saved in the PLC root directory. \n 2209 7976 The file specified does not exist. \n 2210 7977 An error occurred while accessing a file system device. \n 2211 7978 File access was canceled. - You pressed the "END" soft key while a file operation was being executed. - File access was timed out (e.g. connecting network drives, setting up the directory tree). \n 2212 7979 Too many files were opened at the same time (e.g. by background copying). \n 2213 7980 The TNC found a data block or a line with a length of more than 512 characters in the selected file. The TNC is unable to read or process such files. \n 2214 7981 - The given file does not exist - The given file has been deleted since last used - smarT.NC: You selected an .HU program that uses a point table that does not exist on the TNC hard disk \n 2228 8001 You attempted to use FN17/FN18 to exchange data between the NC program and an OEM real-time application, although the real-time application is not active. \n 2229 8002 You attempted to use FN17/FN18 to exchange data between the NC program and an OEM real-time application, which resulted in an error in the real-time application. \n 2233 8005 You tried to make a major change to the format of an NC block. \n 2255 8032 You have opened too many simultaneously active LSV-2 connections over the Ethernet interface. \n 2256 8043 You tried to compile the PLC program while running a TNC program. \n 2257 8044 The externally compiled PLC binary file was activated, not the associated source file. \n 2258 8049 You have write-protected a dependent file (.DEP). \n 2261 8071 - You tried to switch to the section window by soft key although the section file (*.SEC.DEP) is a read-only file. - An internal error has occurred when you tried to switch to the section window by soft key. \n 2262 8072 You write-protected the section file (*.SEC.DEP) although this is not permitted. \n 2284 8090 In a pocket cycle (rectangular pocket, circular pocket, SL cycle), you defined the plunge type to be either helical or reciprocating. This is not possible due to space. \n 2285 8110 A running NC program was: - aborted by a power failure - canceled by shutting down the software (e.g. Windows crashed) - terminated by a program crash \n 2288 7798 CC reports an error code for which there is no error message yet. \n 2289 8114 \n 2290 8115 \n 2291 8116 \n 2292 8117 \n 2293 8118 \n 2294 8119 \n 2295 8120 \n 2296 8121 \n 2297 8122 \n 2298 8123 \n 2299 8124 \n 2300 8125 \n 2301 8126 \n 2302 8127 \n 2303 8128 \n 2304 8129 \n 2305 8130 \n 2306 8131 \n 2307 8132 \n 2308 8133 \n 2309 8134 \n 2310 8135 \n 2311 8136 \n 2312 8140 \n 2313 8141 \n 2314 8142 \n 2319 8213 The entered value is invalid or lies outside the permissible limit values. \n 2323 499 A file needed by the TNC is not available. \n 2324 8231 You tried to use the FUNCTION TCPM function with the AXIS SPAT option, although - you have not programmed all three spatial angles A, B and C, or- one rotary axis is already at a position other than 0. \n 2326 8284 The name of the motor (or power module) with the electronic ID label was not found in the motor table (or power module table). \n 2328 8290 The calculated path of the tool results in a violation of the defined working envelope of the machine, e.g. by the tilting or swiveling element. \n 2329 8292 Power supply of the PLB 510 basic module missing. \n 2330 8293 A short circuit has occurred at a digital output of a PLC 16-8 input/output module. \n 2348 8401 An unknown PLC module was programmed. \n 2363 8494 The CC does not sending any version numbers within 2 s (STOPP 0). \n 2364 8495 The CC does not find any SG-MP checksums within 2 s (STOPP 0). \n 2367 8591 You tried to run the TURN positioning behavior with the PLANE function during active M128 or active FUNCTION TCPM. \n 2391 8643 You programmed a CYCL CALL POS block without all of the principal axis coordinates X, Y and Z. \n 2392 8644 You programmed an incremental CYCL CALL POS block without first having programmed a CYCL CALL POS block with absolute coordinates. \n 2393 8658 After a change to the kinematics (e.g. head exchange), you did not set a new datum in all three main axes X, Y and Z, and then tried to start a new program. \n 2394 8757 The fan in the MC 422B is defective. \n 2395 8758 \n 2402 8892 The coupling function via Module 9226 cannot be run because the formula cannot be translated. \n 2414 502 You programmed an FK arc without a direction of rotation. \n 2415 503 - Tool radius 0 is active. - A rounding arc does not fit between two contour elements. \n 2416 504 FK programming: You have entered contradictory values. \n 2417 505 FK programming: The contour was not resolved by the end of the program. \n 2418 506 FK programming: You programmed with polar coordinates without first defining an FPOL. \n 2419 507 FK programming: Conventional blocks may follow an FK block only if the FK block led to a complete resolution of the contour. Exceptions: - RND block - CHF block - L block containing only motion in the tool axis or auxiliary axis. \n 2420 508 FK programming: - FSELECT block follows an already resolved contour. - FSELECT block follows an as yet unresolvable FK contour (shown in red). \n 2421 509 FK programming: An FK block in which CLSD (contour end) is programmed contains incremental axis coordinates. \n 2422 510 You programmed a rounding arc or chamfer that does not immediately follow a positioning block. \n 2423 511 You programmed a rounding arc or chamfer between tangential contour transitions. \n 2424 512 A straight line before or after an RND or CHF block has the length 0. \n 2425 513 The CHF block is not located between two line blocks. \n 2426 514 The programmed chamfer length is too large. \n 2427 515 You attempted to begin a tool radius compensation on a circular path. \n 2428 516 You attempted to end a tool radius compensation on a circular path. \n 2429 517 FK programming: The information does not suffice for calculation of an FK contour. \n 2430 518 FK programming: Arithmetical error in the calculation of an FK contour (e.g., division by 0, root of a negative number). \n 2431 519 FK programming: An FK positioning block (FL,FC,FLT,CT) can follow a conventional positioning block only if the end point of the conventional block is unambiguously defined, i.e.: - The conventional positioning block must not contain any Q parameters. - The first FK block must not follow a label. \n 2432 522 FK programming: Relative references are possible only to the last 64 positioning blocks: - A reference was made to a more distant block - A reference was made to a block that, at that point in the program, would lead to more than one FK solution. \n 2433 523 FK programming: You programmed a relative reference to a CC block. \n 2434 525 FK programming: You did not program both coordinates in an auxiliary point. \n 2435 526 FK programming: You attempted to start an FK graphic while the TNC was already running a part program. \n 2436 527 The blank form is so large that the graphic elements cannot be displayed by the graphics processor. \n 2437 528 Programming graphics: During reduction of a programming graphic simulation the window section exceeds the limits of the graphics processor. \n 2438 529 During enlargement of a programming graphic simulation the window section exceeds the limits of the graphics processor. \n 2439 530 In a programming graphic simulation you moved the selection frame to the edge of the window, which calls for a reduction of scale beyond the capability of the graphics controller. \n 2444 9785 - Internal software error \n 2455 10248 The block scan evaluated an NC function that cannot be used with mid-program startup (e.g. M142, M143). \n 2457 10521 For the autostart function, you entered a starting time that lies in the past. \n 2467 10664 The TNC cannot generate the tool usage file now because it is being read by another application. \n 2468 10665 Programming graphics generation had to be terminated due to an internal error. \n 2476 10672 The PLC in-code tracer cannot be started because one of the SPAWN/SUBMIT jobs in the system blocked all context switching for more than 3 seconds. \n 2497 10710 Reaction time of Profibus was exceeded. The PLC program executed a PLC cycle with old PROFIBUS input data after this warning occurred. \n 2498 10711 Reaction time of Profibus was exceeded. The PLC program executed two PLC cycles with old PROFIBUS input data in succession after this warning occurred. \n 2500 10942 \n 2501 10949 The lateral infeed, which is calculated from the active tool radius and the path overlap factor, is too small. \n 2502 10950 The path overlap factor defined in a fixed cycle is too large. \n 2514 11044 You entered 0 for the cylinder radius Q16 for the cylinder surface machining cycle. \n 2515 11045 More than 44 entries via Marker M4753 in queue Q_PLCLOGBOOK. \n 2534 11232 You started the pattern generator or the contour programming while in a machining form and from there tried to switch to another operating mode. \n 2538 11275 You tried to create a new file without first defining the appropriate file type. \n 2539 11391 You pressed a key that is locked at present by the NC software. \n 2540 11410 A program run (test run) showed that a globally effective Q parameter is not defined. \n 2541 11411 A program run (test run) showed that a globally effective Q parameter is defined twice. \n 2542 11412 You tried to test or run a unit program in which one or more global cycle parameters are not defined in the program header. \n 2543 11413 You tried to switch to the smarT.NC mode although a program is being run in the test-run mode. \n 2544 11442 In a pattern or a frame, you tried to define two rotary positions at once. \n 2545 11453 You tried to assign a name to a new file, although that name already exists. \n 2546 11454 You tried to insert the UNIT 700 (program header), although it already exists. \n 2551 11559 You tried within an FK sequence to activate the LOOK AHEAD function with M120 LA. \n 2552 11574 The M function M114 was programmed although no corresponding description of the machine geometry had been saved in a kinematic table. \n 2553 11575 You programmed a Cycle 27, Cylinder Surface (ISO: G127), although the axis configured in the active kinematic table was either not the programmed rotary axis or not a rotary axis at all. \n 2554 11576 Coordinates of rotary axis center are missing in the active kinematic table. \n 2555 11577 You used M128 before the machine geometry was defined in a kinematic table. \n 2556 11578 In the Tilted Working Plane function you have the spatial-angle input mode active although the TNC does not support this mode for your machine configuration. \n 2557 11579 - In OEM.SYS, under the keyword KINEMATIC=, an incorrect path or file name was entered for the allocation table for kinematic descriptions - The allocation table for kinematic descriptions is missing. \n 2558 11580 In the Manual operating mode, the Tilt Working Plane function is inactive. \n 2559 11581 You tried to run a PLANE function although your machine is not configured for it. \n 2560 11582 - Internal software error - Control hardware defective \n 2561 11585 A PLC strobe function (e.g. PLC positioning) was programmed, although the NC program is running and no NC strobe is present. \n 2562 11586 At present, the system is preventing use of the test graphic. \n 2564 11588 You tried to edit a program that is being edited in the smarT.NC mode. \n 2565 11589 You tried to edit form data that are being edited in the Programming and Editing mode. \n 2566 11593 The connected controller unit is not supported by the main computer because the required option is not enabled. \n 2567 11595 You tried to delete a file that is selected in another operating mode. \n 2569 11597 Interference detected at the interface of the PL 510. \n 2570 11598 Not enough free memory on the PLC partition. \n 2573 11601 - Internal software error \n 2577 11750 You tried to use the "Recent Files" function to open a file that was moved or no longer exists. \n 2578 11751 You changed the write-protection property of the file outside of the TNC application while this file was selected for editing on the TNC. \n 2579 11752 You tried to assign the same label name in more than one NC block containing LBL SET. \n 2580 11753 A label name in the active NC program was assigned more than once using the LBL SET function. \n 2581 11754 You tried to use LBL CALL to call a subprogram or program section repeat that does not exist. \n 2582 11755 You tried to assign the same label name in more than one NC block containing LBL SET. \n 2583 12214 A file is still open on the USB device you want to remove. The device can therefore not be removed from the directory tree of the iTNC. If you nevertheless remove the device, data losses or malfunctions may occur. \n 2584 12215 You removed a USB device from the interface without removing it from the iTNC directory tree before. This may result in data losses or malfunctions. \n 2585 12283 In Cycle 240 Centering you defined parameter Q343 such that centering is done with respect to the diameter. However, no point angle is defined for the active tool. \n 2586 12284 The combination of the parameters Depth (Q201) and Diameter (Q344) defined in Cycle 240 Centering under Select depth/diameter (Q343) is not allowed. \n 2587 12358 You have aborted the search process. \n 2591 12759 After selecting a long smarT.NC program, you canceled the buildup of the tree view. The TNC therefore cannot show the complete tree structure of the program within smarT.NC, nor can you test or run the program. \n 2592 12760 Rotational speed of the housing fan is too low. \n 2593 12767 Reentrance into smarT.NC is at present not possible. \n 2594 12768 The program that you selected cannot be processed by the TNC because it has too many units. \n 2595 12770 The 3,3-V power supply of the control is too high. \n 2596 12771 The 3,3-V power supply of the control is too low. \n 2597 181 Error in the conversion of the programmed workpiece blank in the FK graphics: One edge length is negative (min. and max. limits were switched). \n 2598 520 FK programming: A tangential FK block (FLT,FCT) can follow a conventional positioning block only if the approach direction is unambiguously defined. \n 2599 521 FK programming: You programmed a relative angle reference to a part program block whose slope angle is not constant. \n 2600 524 FK programming: In FPOL you did not program both coordinates of the working plane. \n 2601 12822 \n 2602 12823 You defined the cutter radius for the active tool in the tool table as less than or equal to 0. \n 2603 12824 More than 5 axes were defined for PLC positioning in one positioning block, but the TNC can move no more than 5 axes simultaneously. \n 2604 12830 You tried to run Cycle 254 with the slot position 0 (Q367=0) in conjunction with the point pattern Cycle 221. \n 2605 12837 In the first block of a subprogram, you did not defined both coordinates of the working plane. \n 2616 12857 You tried to download a program with over 100 NC blocks into the demo version of the iTNC 530 programming station. \n 2624 6091 No symbolic operands are being used in the PLC program. \n 2646 13066 You tried to change a preset value in an active tool-axis system. \n 2647 13072 You tried to set a datum although the M114 function is active. \n 2648 13147 An attempt was made to activate a function that requires a running PLC program. \n 2649 4 Not all tests were completely run. \n 2650 9 The CRC sum of the compiled PLC program is incorrect. \n 2651 11 General file management error. \n 2652 12 General software error in the main processor task. \n 2653 14 Insufficient memory left free to open a machine parameter file. \n 2654 16 Internal error: incorrect interrupt \n 2655 19 Internal error: A task was given an unknown command or a command with illegal parameters. \n 2656 29 You have attempted to simultaneously move more axes than is possible with the export version of the control. \n 2657 33 The CRC sum of the EPROMs IC-P1 and IC-P2 is incorrect. \n 2658 34 The CRC sums of the EPROMs IC-P3 and IC-P46 is incorrect. \n 2659 40 The axis is moving at least 4 times slower or faster than commanded by the nominal speed command output. \n 2660 43 The motor is moving while the axis slide is not, or vice versa. \n 2661 13741 You did not enter the end-of-block character in the given line of the format description file. \n 2662 13742 You entered more than 32 keywords in the given line of the format description file. \n 2663 13743 You defined an unknown keyword in the given line of the format description file. \n 2664 13744 You used an unknown statement in the given line of the format description file. \n 2665 13745 You used an invalid format statement in the given line of the format description file. \n 2666 13746 You did not close the format description in the given line of the format description file. \n 2667 13747 You defined an excessively long keyword in the given line of the format description file. \n 2668 13748 In the given line of the format description file, you defined a keyword that requires the entry of an index although no index had been defined. \n 2669 13749 In the given line of the format description file you did not define a closing bracket (]) after a keyword with an index. \n 2670 13750 The mask file that you defined could not be opened. \n 2671 13751 The TNC cannot make the output file: - Output file is selected in the Programming and Editing mode. - The destination directory does not exist. \n 2672 13154 Two collision-monitored objects have come below a certain minimum clearance. |<-->| Warning - coarse clearance |<->| Warning - fine clearance \n 2673 13155 The machine was moved into a collision-protected area. Further movement would result in a collision. |<>| Collision protection prevents further movement of the axes. \n 2674 13156 The Profibus firmware on the Profibus master could not be updated. \n 2675 13302 The file entered in OEM.SYS under "MPFRAGMENTFILE =" cannot be opened: \n 2676 13340 You tried to use the FN17 function to write a value that lies outside of the permitted input range. \n 2680 13348 You tried to change the TNC network settings although DHCP is active (Dynamic Host Configuration Protocol, dynamic IP address assignment). \n 2684 13381 You pressed the RESET COLUMN soft key. \n 2685 13387 You defined a fixed cycle with the depth 0. \n 2686 13475 You tried to use a workpiece blank definition from an .hu program, but you did not select the current contour program from an .hu program. \n 2687 13476 You tried to insert a block from the clipboard, but the clipboard is empty. \n 2688 13477 - Inverter defective - Incorrect wiring of the braking control (short circuit to 0 V, short circuit to 24 V) \n 2689 13478 - Inverter defective - Incorrect wiring of the braking control (short circuit to 0 V, short circuit to 24 V) \n 2691 13486 The actual speed of the spindle varies too greatly from the programmed nominal speed. \n 2692 13487 - You connected to the USB bus a device that the TNC does not support. - You have a software version that does not support USB block devices (memory sticks, hard disks, CD-ROM drives). \n 2697 13752 You tried to edit a unit although the marking function is active. \n 2698 13753 You used FEZ to define a feed rate without having defined the number of teeth for the active tool. \n 2699 13758 You tried to activate the M118 function during active collision monitoring. \n 2700 13761 You tried to edit a point table with the .PNT file type. \n 2701 13769 During M128 or TCPM FUNCTION, the tolerance of the standstill monitor (MP1110.x) of an open-loop axis (displayed only) was exceeded. Maybe you tried to position this axis manually. \n 2702 13770 An error occurred during automatic generation of the cycle structure. Working with touch-probe and/or machining cycles is not or not entirely possible. \n 2728 13816 You tried to use a feature that is not enabled on your TNC by the Feature Content Level (FCL) management. \n 2730 13825 You tried to use a software option that is not enabled on your TNC. \n 2731 13827 You tried to open a DXF file that cannot be edited by the TNC. \n 2735 13838 The TNC locks keys during a status change, but the lock was opened because the status change was not completed within 15 seconds. \n 2739 13945 You tried to use a feature that is not available on your machine. \n 2740 13957 You tried to select a file that is editable only in the smarT.NC operating mode. \n 2741 13958 In an inch program you combined the FU functions (feed rate in in./rev) or FZ (feed rate in in./tooth) with the M136 function (feed rate in 0.1 in./rev). \n 2743 13960 You tried to select the smarT.NC operating mode although the cycle structure is not correctly set. \n 2744 13961 In the PATTERN DEF block, you programmed the first position with incremental coordinates. \n 2748 14017 You tried to switch on the touch probe cycle 441 to switch on the angle tracking, although this function is deactivated by machine parameter 6165. \n 2749 14019 During the switch-off test the CC performs a current measurement started by the MC. If there is no reaction after max. 2 s, it results in a Stop0 reaction. \n 2750 14020 Software error \n 2751 14021 Software error \n 2752 14022 One or more machine keys that are connected with "MT" (machine key) are active on the CC side. \n 2753 14023 Machine-key permissive key is depressed on the MC side. \n 2754 14024 Machine-key permissive key is depressed on the CC side. \n 2755 14025 Handwheel permissive key is active on CC side. \n 2756 14026 Tool changer permissive key is active on CC side. \n 2757 14027 One or more protective doors (A/S/T) of the CC are open. \n 2758 14032 Internal calculations in combination with the Scaling Factor or Axis-Specific Scaling Factor cycles resulted in an impermissibly large numerical value. \n 2761 14138 The cycle can only run in negative direction (positive in Cycle 204) because the machine parameter "suppressDepthErr" is set to on. \n 2762 14156 - You tried to move the tool with the "virtual tool axis." The definition for the tool axis does not exist or was canceled. \n 2763 14253 You have hidden or disabled a point for which a pre-positioning height is defined. In some cases this could lead to a collision. \n 2764 14254 Permissive button of machine operating panel or handwheel is depressed. \n 2765 14255 Permissive button of machine operating panel or handwheel is depressed. \n 2766 14299 You tried to convert a program containing an ISO program call. \n 2767 14434 You defined the range definition in Cycle 30 (DIN/ISO: G60) incorrectly. \n 2770 14479 You tried to select a datum number by soft key although no datum table is selected in the program header. \n 2771 14486 The iTNC cannot simulate the M140 MB MAX function because the working space monitoring is inactive. \n 2772 14487 You have connected several string variables and, in doing so, have exceeded the maximum permissible string length. \n 2773 14518 In a TOOL CALL or TOOL DEF block you tried to define a tool number although it is prohibited by machine parameter. \n 2774 14519 In a TOOL CALL or TOOL DEF block you tried to define a tool name although it is prohibited by machine parameter. \n 2775 14520 You tried to divide by 0. \n 2776 14521 You tried to calculate the root of a negative number. \n 2777 14522 You tried to calculate the logarithm of a negative number. \n 2778 14523 You tried to form the tangent of a 90° angle (or its integral multiple). \n 2779 14525 In Cycle 22 (ISO: G122), you tried to define the feed-rate factor Q401 to be less than 1. This upgrade feature is locked on your TNC by the FCL management. \n 2780 14550 In a formula calculation the absolute value of the argument is greater than 1. \n 2781 14551 In a formula calculation the absolute value of the argument is greater than 1. \n 2784 15439 You tried to edit the active preset although M128 or the TCPM FUNCTION is active. \n 2785 15465 - No cutting data tables available in the TNC:\ directory - No workpiece material defined by WMAT block - No tool material defined in TOOL.T - No cutting data table defined in TOOL.T - Combination of workpiece and tool material not available in the active cutting data table \n 2786 15466 A service/support file listed in OEM.SYS is faulty or missing. \n 2791 15491 Someone tried to set a breakpoint through the data interface. \n 2796 15614 You did not define a probing direction in probe cycle 4. \n 2799 15658 You entered a spindle speed S greater than the maximum speed defined for this tool in the tool table TOOL.T. \n 2800 15672 You tried to rename an entire drive. \n 2801 15673 You tried to copy an entire drive. \n 2802 15674 You tried to delete an entire drive. \n 2803 15675 You tried to open a file that cannot be processed by the TNC. \n 2804 15687 - Defective hardware - Spindle cannot be controlled \n 2805 15688 Axes cannot be controlled \n 2806 15691 During an active FUNCTION TCPM, AXIS SPAT function, you tried to resume a program by using the GOTO block number key. \n 2808 15766 In the TOOL CALL block(DIN/ISO: T block) you programmed a tool axis that was locked for the currently active kinematics by your machine tool builder. \n 2809 15767 Traverse in safe mode through TNCopt exceeded the permissible range. \n 2810 15923 Settings for the PLC memory layout have changed. \n 2811 15967 Your hardware does not have enough main memory to start the help system. \n 2812 15973 You used function M141 (suppress touch-probe monitor) while the collision monitor was active. \n 2814 16007 A reference run was started in one axis by PLC module, then the M function was acknowledged before the reference run could finish. As a result the NC program cannot continue. \n 2815 16010 - Controller unit with operator safety module is not supported with the installed software \n 2820 16198 Hardware is defective \n 2821 16362 Although SH1B.x=1, RDY.x=0 \n 2822 16363 Although SH1B.x=0, RDY.x=1 \n 2827 16407 The entered values could not be transferred due to an internal error. \n 2828 16408 You tried to swap a linear axis for a rotary axis. \n 2829 16409 When swapping axes, you tried to assign two different axes to the same axis. \n 2830 16410 When swapping axes, you tried to swap an axis for an axis that does not exist. \n 2831 16411 In the global program settings you defined a value that lies outside of the permitted input range. \n 2832 16412 You tried to change the global program settings while the program was running. \n 2833 16413 There has been an indefinable error. \n 2856 16561 There was a spindle overload during adaptive feed rate control. \n 2857 16563 The amplitude of the position encoder signal is too high or the signal for contamination is active. \n 2859 16564 The amplitude of the position encoder signal is too low or the signal for contamination is active. \n 2860 16565 The maximum input frequency was exceeded at a position encoder input. \n 2861 46 Contradiction apparent from comparison of the absolute and incremental positions. \n 2867 16586 In the PLANE AXIAL function you defined a rotary axis that is not described in the active kinematics. \n 2869 16593 MC did not command a braking test although MP2230.x !=0 (i.e., run brake test in this axis). \n 2870 16623 There is an error in the column definition in a freely definable table: - Column name missing - Field width not allowed - Number of decimal places not allowed - Unknown column type \n 2871 16718 - The actual speed of the spindle is too much higher than the programmed nominal speed. \n 2872 16798 In the smarT.NC operating mode you selected the Program Run submode although global program settings were active. \n 2873 16800 You tried in the smarT.NC operating mode to open a file that it cannot depict. \n 2874 16830 - You tried to edit a program that is now being run. - You tried to edit a table that is accessed from within the program that is now being run. \n 2875 17063 An attempt was made to run an NC macro while the machine status was being restored. \n 2877 17161 - Poor resolution of the absolute value from the ENDAT encoder. The resolution cannot be improved with the aid of the incremental track. - Encoder or axis is not stationary or defective during evaluation. \n 2878 17162 - Cannot read an electronic ID label from DSP. - Hardware defective \n 2879 17163 - TRC compensation file could not be transmitted to DSP. - Hardware defective \n 2880 17167 Adaptive feed rate control (AFC): After an overload reaction there was an attempted to call an NC macro, although the AFC entry is missing in the NCMACRO.SYS file. \n 2881 17207 Software error \n 2882 17384 You tried to call the TNCguide help system or set to an Asian conversational language, although your control hardware does not have enough main memory. \n 2884 17386 You tried to conduct a pallet operation although the global parameter setting function is active. \n 2885 17387 During an active M128, you used the global parameter settings to lock axes. \n 2887 17390 In the PLANE AXIS function, you programmed 3 rotary axes with the MOVE option. In this case the TNC would have to move 6 axes at the same time, but it cannot interpolate more than 5 axes. \n