18:01-03
en
Issue 1
1 585 547
Door, door window and
rear view mirrors
18_2407
©
Scania CV AB 1995-08
2
©
Scania CV AB 1995
18:01-03 en
Contents
Removal
Lock ................................................................... 3
Rear view mirror glass ....................................... 3
Door window ..................................................... 4
Door, method 1 .................................................. 6
Rear view mirror ......................................... 8
Door, method 2 ................................................ 10
Fitting
Lock ................................................................. 11
Door window ................................................... 12
Door, method 1 ................................................ 14
Rear view mirror ....................................... 16
Door, method 2 ................................................ 17
Contents
18:01-03 en
©
Scania CV AB 1995
3
Removing lock
1
Remove the door handle 1 by undoing the
two screws on the inside of the door.
2
Remove link 2 in the rear edge of the door
handle, turn 90
°
detach pull rod 3.
Note: Carefully prise off the pull rod and link.
3
Remove the bolts for the lock 4 in the side
of the door.
4
Prise out the lock.
5
Unscrew the central locking motor 5 from
the lock.
In order to change the central locking motor, the
door panel must be removed in order to gain
access to the joint in the electrical cable.
Removing rear view mirror
glass
1
Angle the mirror glass in order to gain
access to the lock spring on the rear.
2
Unplug the electrical connection to the mir-
ror glass.
Fit the parts in reverse order.
Note: Check that the lock spring is engaged.
18_2376
18_2377
Removal
18_2401
2
1
2
3
3
5
5
4
4
4
©
Scania CV AB 1995
18:01-03 en
Removing door window
1
Remove the frame 1 from around the door
window, starting at the upper edge.
2
Remove the screw in the lower edge of
switch panel 2 for the door window winder.
Unplug the electrical connection.
3
Remove door pocket 6.
4
Remove cover 3, armrest 4 and handle 5.
5
Remove fuse (No. 15) for cab lighting.
6
Remove the boarding lamp 8 and pass it
through the hole in the door panel.
7
Remove scraper strip 9.
8
Remove door panel 7, up/out.
Removal
18_2394
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
18:01-03 en
©
Scania CV AB 1995
5
9
Bend a hook to suspend the door window, or
use a strap.
10
Wind the door window almost fully up and
then lower it until it is suspended on the
hook or strap.
11
Disconnect electrical connector 10 for the
door window motor.
12
Detach the arm from the door window
winding mechanism through the hole
behind cover 11.
13
Remove the door opener 15.
14
Remove panel 12 in the door.
15
Drill out the ’pop’ rivets in guide rail 13
for the door window and remove the
screws in the lower edge.
16
Remove the hook or strap holding the door
window.
17
Lift out guide rail 13 and door window 14.
850
18_2403
18_2387
18_2388
18_2389
18_2392
18_2393
Removal
6
©
Scania CV AB 1995
18:01-03 en
18_2394
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Removing door, method 1
1
Remove the frame 1 from around the door
window, starting at the upper edge.
2
Remove the screw in the lower edge of
switch panel 2 for the door window winder.
Unplug the electrical connection.
3
Remove door pocket 6.
4
Remove cover 3, armrest 4 and handle 5.
5
Remove fuse (No. 15) for cab lighting.
6
Remove the boarding lamp 8 and pass it
through the hole in the door panel.
7
Remove scraper strip 9.
8
Remove door panel 7, up/out.
Removal
18:01-03 en
©
Scania CV AB 1995
7
850
18_2403
18_2387
18_2388
18_2389
9
Bend a hook to suspend the door window, or
use a strap.
10
Wind the door window almost fully up and
then lower it until it is suspended on the
hook or strap.
11
Disconnect electrical connector 10 for the
door window motor.
12
Detach the arm from the door window
winding mechanism through the hole
behind cover 11.
13
Remove the door opener 15.
14
Remove panel 12 in the door.
15
Disconnect the electrical cables to the cen-
tral locking system.
Removal
8
©
Scania CV AB 1995
18:01-03 en
Removing rear view mirrors
16
Remove the cover from the lower bracket
on the rear view mirror.
17
Undo the lower bracket and unplug electri-
cal cables.
18
Undo the upper bracket and remove the rear
view mirrors.
19
Remove the entire cable loom from the
door.
20
Remove the guide for the step in the lower
edge of the door.
18_2378
18_2379
18_2380
18_2381
Removal
18:01-03 en
©
Scania CV AB 1995
9
22
Remove the door stop in the door attach-
ment.
18_2383
21
Remove the gas spring from the cab corner
and fold forwards.
23
Use an overhead hoist and attach the door
using a lifting strap.
N.B. Be careful not to damage the aluminium
frame around the window.
18_2384
Removal
100287
10
©
Scania CV AB 1995
18:01-03 en
24
Remove the covers over the door hinge.
25
Remove the cover strip from the corner pil-
lar.
26
Remove the door pins using hammer and
drift.
27
Lift the door with the overhead hoist.
Removing door, method 2
1
Lower the door window about 1 dm.
2
Remove the cover under the instrument
panel.
3
Unplug the electrical connector.
4
Remove the cable clip under the front door
pillar.
5
Prise away the cable lead-in.
6
Pull out the wiring harness.
7
Remove the door stop in the door attach-
ment.
Removal
18_2386
18_2385
18_2383
18:01-03 en
©
Scania CV AB 1995
11
8
Use an overhead hoist and attach the door
using a lifting strap.
N.B. Take care not to damage the frame around
the door window.
9
Remove the covers over the door hinge.
10
Remove the cover strip from the corner pil-
lar.
11
Remove the door pins using hammer and
drift.
12
Lift the door with the overhead hoist.
Fitting lock
1
Fit the central locking motor 5.
2
Fit lock 4 in the door end panel.
3
Fit door handle 1 in pull rod 3 and link 2.
Screw in place.
18_2401
2
1
2
3
3
5
5
4
4
18_2385
Removal/fitting
18_2386
12
©
Scania CV AB 1995
18:01-03 en
Fitting door window
1
Fit door window 14 in guide rail 13.
2
Align the door window in the guide rails in
the door.
3
Fit the hook or strap to the window. Lower
the window into the space.
4
Pop rivet the guide rail to the door, starting
with the upper holes.
5
Raise the window and attach the hook or
straps.
6
Do up the screws in lower edge of guide
rail.
7
Locate panel 12, align arm with window
winder mechanism and fit cover 11.
8
Remove hook or strap.
9
Fit the door opener 15.
10
Fit electrical connector 10 to window
winder motor.
Fitting
18_2393
850
18_2403
18_2389
18_2387
18:01-03 en
©
Scania CV AB 1995
13
18_2394
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
11
Temporarily connect switch panel 2 and
check that the window moves easily in the
guide rail.
12
Thread the boarding lamp 8 through the
hole in the door panel.
13
Fit door panel 7.
14
Bolt on the boarding lamp.
15
Fit handle 5, armrest 4 and cover 3.
16
Fit scraper strip 9.
17
Fit door pocket 6.
18
Connect switch panel 2 to window winder
and screw in place.
19
Fit door moulding 1 around the door win-
dow.
20
Fit fuse (No. 15) for cab lighting.
Fitting
14
©
Scania CV AB 1995
18:01-03 en
Fitting door, method 1
1
Lift the door into position using overhead
hoist.
2
Using a hammer, knock the pins through the
door hinges.
3
Fit the cover strip to the corner pillar.
4
Fit the plastic covers on the upper hinge.
5
Fit the door stop.
6
Fit the cab corner gas spring.
18_2386
18_2385
18_2383
Fitting
100287
18:01-03 en
©
Scania CV AB 1995
15
7
Fit the guide for the step to the lower edge
of the door.
8
Insert the entire cable loom through the door
and connect to the central locking system.
9
Locate panel 12, align arm with window
winder mechanism and fit cover 11.
10
Remove hook or strap.
11
Fit the door opener 15.
12
Fit electrical connector 10 to window
winder motor.
13
Temporarily connect switch panel 2 and
check that the window moves easily in the
guide rail.
14
Thread the boarding lamp 8 through the
hole in the door panel.
15
Fit door panel 7.
16
Bolt on the boarding lamp.
17
Fit handle 5, armrest 4 and cover 3.
18
Fit scraper strip 9.
19
Fit door pocket 6.
20
Connect switch panel 2 to window winder
and screw in place.
21
Fit door moulding 1 around the door win-
dow.
22
Fit fuse (No. 15) for cab lighting.
Fitting
18_2394
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
©
Scania CV AB 1995
18:01-03 en
Fitting rear view mirrors
23
Fit rear view mirrors, connect electrical
cable, screw upper and lower bracket in
place.
24
Fit cover to the lower bracket on the rear
view mirror.
18_2378
18_2379
18_2380
18_2381
Fitting
18:01-03 en
©
Scania CV AB 1995
17
Fitting door, method 2
1
Lift the door into position using overhead
hoist.
2
Using a hammer, knock the pins through the
door hinges.
3
Fit the cover strip to the corner pillar.
4
Fit the plastic covers on the upper hinge.
5
Fit the door stop.
6
Pull the wiring harness through the door pil-
lar using e.g. a piece of steel wire.
7
Fit the cable lead-in.
8
Fit the cable clip under the front door pillar.
9
Connect the electrical connector.
10
Fit the cover under the instrument panel.
Fitting
18_2385
18_2386
18_2383